Active Intent S001S User manual

4-IN-1 SWING SET
Owner’s Manual
Model: S001S
Un
IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future
reference.
The specification of this product may vary from this photo, subject to change without notice.

1
Table of Contents
SAFETY INSTRUCTIONS ----------------------------------------------------------------------------------------- 2
CARE & MAINTENANCE INSTRUCTION-------------------------------------------------------------- 4
PARTS LIST ----------------------------------------------------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS-------------------------------------------------------------------------------------- 10
Customer service number: 0800 422 274
MON –FRI: 8AM –5PM
SAT –SUN: 9AM –4PM
Marketed By: The Warehouse LTD
26 The Warehouse Way, Northcote,Auckland

2
Safety Instructions
Warning:
- This swing set is for family domestic use only.
- This swing set is designed for use by children 3-8 years of age weighing no more than 45kgs.
- This swing set has a maximum weight limit of 500lbs.
- This swing set is for outdoor use only.
- Children of all ages must be supervised by an adult at all times when using this swing set.
- Adult assembly of this swing set is required. Two adults are recommended for assembly.
Fully read and understand these instructions prior to assembling and using this
swing set.
This Product is for Family Domestic Use Only.
YOUR CHILD’S SAFETY DEPENDS ON YOU.
OBSERVING THE FOLLOWING SAFETY PRECAUTIONS AND WARNINGS
REDUCES THE LIKELIHOOD OF SERIOUS OR FATAL INJURY.
Read this manual and follow all instructions before using and assembling your playground equipment.
This playground equipment must be assembled and disassembled by an adult. It is recommended to have
two adults assemble this playground equipment.
Always provide on-site adult supervision for children of all ages at all times.
This playground equipment is designed to be used by no more than 5 children between the ages of 3 to 8
years at any one time. Children should not weigh more than 100 lbs (45.45 Kg.) each.
WARNING: Lawn swings (if applicable) are designed for use by children over two years of age. Use by
children under the age of two can result in entrapment between the seat and back areas. NEVER place
children in rear facing position or with legs between the seat and backrest because the child’s body may
pass through the opening causing entrapment of the child’s head.
Always ensure the playground equipment sits on level ground!
To prevent serious injury to children, the playground equipment must not be used until properly assembled
and anchored.
Do anchor all playground equipment. Do not install over concrete, asphalt, gravel on any hard surface. A
fall onto a hard surface can result in serious injury to the user.
It is recommended that the playground equipment be placed in concrete. Be certain that all anchoring
devices (including concrete) are placed below the level of the playing surface or below ground level to
prevent tripping.
Do not assemble or place playground equipment near any obstruction or sharp objects! Place playground
equipment on level ground, not less than 6ft (1.8m) from any structures or obstacles such as fence, garage,
shed house, overhanging branches, laundry line, electrical wires.
Do not let children use the playground equipment until it is properly assembled and anchored.
Provide proper surface material cover for this equipment prior to using this equipment. See page 4 of this
manual for more information.
If any bolts & nuts are missing, do not use this playground equipment!
If the child has any physical condition that may affect his/her ability to use this equipment, one shall consult
a physician, before allowing the child to use this equipment.
Do not allow reckless playing, such as jumping off swing, slide, or glide ride.
Do not allow more than one child to play on the swing, trapeze bar or slide at any one time. Children must
take turns using the slide.
Do not allow children over the weight limit to use this equipment. Adults should never ride on any of the
swing seats, trapeze or slide.
Dress children appropriately while on and around this equipment. (Do not allow children to wear ponchos,
scarves, jewelry or any other loose fitting clothing that is potentially hazardous while using playground

3
equipment).
Instruct children not to use the equipment in any manner other than intended.
Teach children to sit in the centre of the swing play items, with their full weight in the centre of the seats.
Do not allow children to stand on the seats. One child per seat only! Do not allow children to lean to the
side when riding on other rides, structural members or collide with other playmates.
Instruct children not to walk too closely in front of, behind, or between moving items.
Instruct children to keep a safe distance away to avoid being struck by items in play.
Instruct children not to twist swing chains or ropes or loop them over the top support bar since this may
reduce the strength of the chain or rope and may result in failure.
Instruct children to avoid swinging empty play items. These may strike other children or come back and
strike you.
Instruct children not to get off equipment while it is in motion. Do not allow children to jump from moving
play items.
Do not allow children to swing play items more than 60 degrees.
Do not allow children to climb or play on equipment when equipment is wet. Slip or falls may occur.
Check the openings between rollers and sliding surfaces of roller slides for foreign materials that could be
potentially hazardous to users.
Verify that suspended climbing ropes, chain, or cable are secured at both ends, and verify that suspended
climbing ropes, chain, or cable cannot be looped back on itself.
Instruct children not to attach items to the playground equipment that are not specifically designed for use
with the equipment such as but not limited to jump ropes, clothesline, pet leashes, cables and chain as they
may cause a strangulation hazard.
Instruct children not to go down slide head first.
Check slide bed for extreme heat before letting children use slide ( When exposed to direct sunlight )
Do not allow children to climb on swing from structural members (Legs, top bar and chin bar). These are
structural components only and NOT play features.
Do ensure that all nuts and bolts are completely tightened after assembling the playground equipment.
Dispose of all packaging properly after unit has been assembled.
Please retain the instruction manual for future reference and review each season.
WARNING
Please read this instruction manual before you start with the assembly or use this swing set.
You must follow all safety instructions while using this equipment; Be absolutely sure that the
surface, on which this swing set is set up on, is properly surfaced with fine sand, wood chips
or double shredded bark mulch.
Do not use this swing set on hard pack soil, concrete or any kind of hard surface. Read all
cautionary statement before using this equipment.

4
CARE & MAINTENANCE INSTRUCTION
It is important to perform the following maintenance inspections at the beginning of each season and twice monthly
thereafter.
*Inspect all nuts and bolts for tightness and tighten as required. It is particularly important that this procedure
be followed at the beginning of each season.
*Remove plastic swing seats slide and take indoors or do not use when temperature drops below 32˚F (0ºC).
*Inspect swing seats, ropes, cables and chains for evidence of deterioration. Replace as needed.
*Inspect all coverings for bolts and sharp edges to be certain they are in place. Replace when necessary.
*Oil all metallic moving parts monthly during the usage period.
*Inspect metal tubing and slide bed for damage and sharp edges. Replace when necessary.
*Sand rusted areas on metal tubing and repaint using a nonlead-based paint meeting the requirements of Title
16 CFR Part 1303.
*If slide bed is exposed to direct sunlight, always check bed to ensure it is not too hot for children use. Pour
cold water onto the slide bed until it cools. Inspect slide bed periodically during use. Replace when
necessary.
*Plastic components should be replaced every three years.
DISPOSALINSTRUCTIONS
*When it is time to dispose of the playground equipment, please use care when disassembling the playground
equipment. Dispose in a safe place and manner so as not to present any hazards to any individual. Wear
heavy duty working gloves!
*Be sure to completely disassemble the whole swing and slide sets, before disposal.
*Do not leave partially disassembled equipment in area where accessible by children.
*Consumer may wish to recycle the steel tubing, please take the frame to your local recycling centre.
*All plastic part could be recycled, take it to your local recycling centre.
*Do not let children play with any disassembled parts destined for disposal, such as chain, slide, tubings, bolts,
nuts, screws!
CAUTION
Do not allow children to use the swing set until the maintenance has been carried out.
The use of the swing set not in first class condition exposes the child to the risk of injury. As a parent,
supervisor, owner or guardian, it is your responsibility to ensure that the swing set is properly maintained.
Spare parts are available through The Warehouse Customer Service centre –0800422 274
Marketed by:
The Warehouse
26 The Warehouse Way
Northcote

5
IMPORTANT CONSUMER INFORMATION SHEET
The Consumer Product Safety Commission estimates that about 200,000 injuries occurred from falls from
playground equipment; which requires hospital emergency treatment. Injuries from falling tend to be the most
serious of all playground injury, and it may be potentially fatal; especially when it is a head injury. The ground
surface under the playground equipment can be an important factor in determining the injury causing potential of a
fall. A fall onto a shock absorbing surface is less likely to cause serious injury in comparison to a fall onto a non
shock absorbing hard surface. Never place playground equipment on hard surface such as concrete, asphalt, rocks,
grass may appear to be acceptable, but in heavy traffic area, it may quickly turn into hard packed earth. Fine sand,
wood chips, shredded bark are acceptable shock absorbing surface, when installed at a sufficient depth under the
playground equipment, it must be maintained properly under and around the perimeter of playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a
life-threatening injury to the head, when falling onto the loose fill surface materials, provided that
these materials are installed and maintained at 6, 9 and 12 inches deep. However, consumers should
recognize that no matter what type of surface material is used, it can not prevent all injuries due to
falls.
FALL HEIGHT IN FEET FROM WHICH
A LIFE THREATENING HEAD INJURY WOULD NOT BE EXPECTED
MATERIAL
6INCH DEPTH
9INCH DEPTH
12INCH DEPTH
Double shredded bark mulch
6
10
11
Wood Chips
6
7
12
Fine Sand
5
5
9
We recommend that surfacing material as per table above should extend a minimum of 6ft in all direction from the
perimeter of the playground equipment. In certain cases, a child may deliberately jump from a moving swing.
Therefore, any shock absorbing material should extend in the front and rear of swing a minimum of 2 times the
height of the pivot point; this height is determined by measuring from a point directly beneath the pivot on the
supporting structure.
Please note this information is intended to assist in comparing the relative shock-absorbing properties of various
materials. No particular material is recommended over another. Every material is only effective when properly
maintained. Material should be maintained and replenished periodically after inspection by user, to maintain the
correct depth necessary for your equipment.
Note: The maximum fall height for this product is 6 feet. The minimum ground clearance between the bottom
of the suspended plays and the playing or ground service must be 8 inches.

6
PARTS LIST
Please prepare the following tools prior to assembling this equipment:
Hammer Tape Measure
(If you intend to install Not included
Anchor, this is needed.)
Flat Head and Philips Wrench
Head Screwdriver (included)
Not included
Allen Wrench
(included)
Parts list for main frame assembly
A1
LEF TOP BAR
1 PC
A2
LONG TOP BAR
1 PC
A4
TOP SECTION LEG
4 PCS
A5
BOTTOM SECTION LEG
4 PCS
A6
CROSS BAR
1 PC

7
A7
CROSS BAR
1 PC
Hardware used for main frame assembly
B1
BOLT 5/16”*63
14 PCS
B2
BOLT 5/16”*63
4 PCS
B3
NYLON NUT 5/16”
18 PCS
B4
PLASTIC CAP
18 PCS
B5
ARC WASHER
32PCS
B6
SPRING WASHER
4 PCS
Parts list for swing seat
J1
PVC COVERED
CHAIN(PREASSEMBLED)
4 PCS
J3
EYE BOLT WITH ATTACHMENT
BOLT(PREASSEMBLED)
4 PCS
J4
EYE BOLT (PREASSEMBLED)
4 PCS
K1
SWING SEAT
2 PCS
Hardware used for swing seat assembly
J6
NYLON NUT 5/16”
8 PCS
J8
ARC WASHER
8 PCS
J9
PLASTIC CAP
8 PCS
Parts list for glide ride
L1
SECTION HANGER
2 PCS
L2
GLIDE SEAT SUPPORT
2PCS

8
M1
TUBE CAP (PREASSEMBLED)
2PCS
M2
SMALL NYLON BEARING
(PREASSEMBLED)
2PCS
M3
LARGE NYLON BEARING
(PREASSEMBLED)
4PCS
M4
GLIDE SEAT
2PCS
M5
FOOTREST
2PCS
Bracket used for glide ride assembly
L4
BRACKET
1 PC
L5
BRACKET CLAMP
1 PC
L6
WASHER
4 PCS
N2
BOLT 5/16”*25
2 PCS
N8
NYLON NUT 5/16”
2 PCS
N14
PLASTIC CAP
2 PCS
Hardware used for glide ride assembly
N1
BOLT 1/4”*35
4 PCS
N2
BOLT 1/4”*45
2 PCS
N5
SCREW Ø5*15
4 PCS
N6
J-BOLT
2 PCS
N7
SPRING WASHER
4 PCS
N9
WASHER
8 PCS
N11
NUT 1/4”
8 PCS
Parts used for slide assembly
X1
SLIDE SUPPORT (WITH 2 HOLES)
1 PC

9
X2
SLIDE SUPPORT
1 PC
X3
SLIDE LEG TUBE
2 PCS
X4
SLIDE TOP SUPPORT BAR
1 PC
X5
SLIDE FRONT SUPPORT
1 PC
X6
SLIDE LADDER STEPS
2 PCS
Y2
SLIDE
1 PC
Hardware used for slide assembly
Y1
PLASTIC CONNECTOR
2 PCS
Z1
BOLT1/4”*35
6 PCS
Z2
BOLT1/4”*60
2 PCS
Z3
BOLT1/4”*100
2 PCS
Z4
WASHER
28 PCS
Z5
NYLON NUT 1/4”
12 PCS
Z8
BOLT 1/4”*90
2 PCS
Z9
BOLT 1/4”*40
4 PCS

10
Assembly instruction
Place the playground equipment on level ground, not less than 6 ft (1.8 m)
from any structure or obstruction such as a fence, garage, house, overhanging
branches, laundry lines, or electrical wires.
Do not install the playground equipment over concrete, asphalt, packed earth,
or any other hard surface. A fall onto a hard surface can result in serious injury
to the user.
TIGHTENING NUTS & BOLTS
*Do not over-tighten the nuts and bolts when you are assembling your playground
equipment. This will allow for some possible adjustments and ease of installation.
*Once you have finished the assembly of the playground assembly, go back over
all of the nuts and bolts and properly tighten all of them before using the
playground equipment.

11
Step 1
Insert A1 into the other end of A2, secure with B1, B5, B4 and B3.
HINT: Please make sure that concave hole faces down.

12
Step 2
Insert small end of A4 into the socket at the end of A1.align holes on them.
Secure with B1, B5, B4 and B3.
Then attach the other two pieces of A4 on the other side to A2 the same.

13
Step 3
Secure with B1, B5, B4, and B3.
Secure with B2, B6, B4, and B3.
Insert A5, into A4, align holes on them.
Attach A6 to A5.
Repeat above to assemble the other A7 to A5 that is attached to the end of A2.

14
Step 4
Insert J3 into holes on A1, A2.
Secure it with J8, J9, and J6
Step 5
J4 and K1 are PRE-ASSEMBLED, if you find it loosely, please follow below step
Attach K1 to J4.
Secure with J7, J9 and J6.

15
Step 6
Attach L5, L4 and L6 to A2 as Shown.
Use special socket wrench and screw- driver to tighten the N3 and N8.
Step 7
Attach M5 to L1.
Secure N5, N13.
M1, M2 and L1 are PRE-ASSEMBLED, if you find it loosely, please follow below step.
Attach M1 to the top of L1, and then align holes on M1 and L1, then insert M2 as shown.
Hold M2 after inserting it into holes of M1.

16
Step 8
Attach L1 to L5, secure with N2, and N11.
Step 9
Insert 2xM3 into L2, then attach L3 to L2 with N6, lightly secure N6 with N9. Do not tighten
completely.
Attach the other L1, L2 and L3 by the as way as described above, once this is done, go back and
securely tighten all N9.

17
Step10
Attach M4 to L2
Secure using N1 ,N9, N7 and N11
Step 11
Attach X5 to Y2
Secure using Z7 and Z1
Attach X4 to Y2
NOTE: Make sure that the bolt holes face up

18
Step 12
Attach X6 to X1 and X2
Secure each side using Z1, Z4 and Z5
Attach X3 to X1 and X2
Align holes and hold in position
Step 13
Insert the end of X4 into X1; secure using Z2, Z4 and Z5.
In the same way, fix the other end of x4 with X2
Insert Z1 into Z4 and insert into X1, X2 and X3 as shown.
Insert Z8 into Z4 and insert into X1, X2 and Y2 as shown.
Z3 and Z5 to X1 Do not secure at this step, to allow adjustment in next step.

19
Step 14
Attach Y1 to X1 and A7, secure using Z3, Z7 and Z4, Z5.
Step 15
Go back to secure Z3 and Z5 to X1, now. Tighten all screws.