AFX MOTORSPORTS CAN006-F User manual

INSTALLATION MANUAL
CAN AM X3
ROOF RACK
CAN006-F
THIS PRODUCT IS FOR OFF ROAD USE ONLY
11 Tighten all the hardware

Rear Leg
Front Leg Center Leg
AFX
Motorsports
products
are
designed
to
best
fit
user’s
ATV/UTV
under
stock
conditions.
Adding,
modifying,
or
fabricating
any
factory
or
aftermarket
parts
will
void
any
warranty
provided
by
AFX
Motorsports
and
is
not
recommended.
AFX
Motorsports
products
could
interfere
with
other
aftermarket
accessories.
If
user
has
aftermarket
products
on
machine,
contact
AFX
Motorsports
to
verify
that
they
will
work
together.
Although
AFX
Motorsports
has
thousands
of
satisfied
customers,
user
should
be
aware
that
installing
bumpers,
rock
sliders,
spare
tire
carriers,
etc.
will
change
the
ride
of
machine
and
may
increase
maintenance
and
part
wear.
Operating
any
off-road
machine
while,
or
after,
consuming
alcohol
and/or
drugs
increases
risk
of
bodily
harm
or
death.
No
warranty
or
representation
is
made
as
to
this
product’s
ability
to
protect
user
from
severe
injury
or
death.
AFX
Motorsports
urges
operators
and
occupants
to
wear
a
helmet
and
appropriate
riding
gear
at
all
times.
By
purchasing
and
installing
AFX
Motorsports
products,
user
agrees
that
should
damages
occur,
AFX
Motorsports
will
not
be
held
responsible
for
loss
of
time,
use,
labor
fees,
replacement
parts,
or
freight
charges.
AFX
Motorsports,
nor
any
3rd
party,
will
not
be
held
responsible
for
any
direct,
indirect,
incidental,
special,
or
consequential
damages
that
result
from
any
product
purchased
from
AFX
Motorsports.
The
total
liability
of
seller
to
user
for
all
damages,
losses,
and
causes
of
action,
if
any,
shall
not
exceed
the
total
purchase
price
paid
for
the
product
that
gave
rise
to
the
claim.
AFX
Motorsports
will
warranty
only
parts
provided
by
AFX
Motorsports.
Any
damage
or
problems
with
OEM
housings,
bearings,
seals,
or
other
manufacturers’
products
will
not
be
covered
by
AFX
Motorsports.
AFX
Motorsports
parts
and
products
are
not
warrantied
if
item
was
not
installed
properly, misused, or modified.
Liability Statement
5/32” Allen Key.
7/16” Combination Wrench.
HOW TO INSTALL
FOR PURCHASING AT AFX MOTORSPORTS
Hardware:
(12x) 1/4” x 1” Bolts
(28x) 1/4” x 3/4” Bolts
(20x) 1/4” x 1/2” Bolts
(12x) 1/4” Plain washer
(60x) 1/4” Lock nut
10 Settle the legs of the roof rack over the OEM roof (the OEM roof
has 3 gaps on each side)
Align the perforations on the roof´s gaps to the perforations on
each Leg of the Roof Rack.
Secure the roof rack to the vehicle using 1/4” x 1” bolts with a
washer and lock nut on each leg
(1x)Front of Roof Rack
(7x) Central
Rails
(2x) Bracket (1x) Rear of Roof Rack
(2x) Center
Legs
(2x) Front Side
(2x) Rear Side
(2x) Rear
Legs
(2x) Front Leg
Front Leg

Install rear frame assembly onto rear side rails (as it is shown in
the image). Use four 1/4x 1/2” screws with nut.
(Do not tighten yet)
Rear Roof Rack
1/4 x 1/2” Screw
Nuts
Align 3 central rails with the perforations (as it is shown in the
image). Use twelve 1/4” x 3/4” screws with nut, inserting them
bottom-up.(Do not tighten yet)
Central rail
8
Join the roof Rack to the Rear legs. Align the perforations and
use 1/4”x 1/2” bolts with lock nuts.
3
Install Front frame Assembly onto front side rails (as it is
shown in the image). Use four 1/4 x 1/2” screws with lock nut
(Do not tighten yet)
Laterals
1/4x 1/2 “ screw
Make sure the perforations of the
rear legs align to the perforations
on the rear side.
Make sure the perforation of the
center legs align to the perforation
on the rear side.
9
Join the roof Rack to the center legs. Align the perforations and
use 1/4”x 1/2” bolts with lock nuts.

7
Join the roof Rack to the front legs. Align the perforations and
use 1/4”x 1/2” bolts with lock nuts.
Align the last central rail wih the perforations of the Bracket
#3 (As itis shown in the image). Use four 3/16 x 3/4” screws
with nut, inserting them bottom-up.
4
6
Align 3 central rails with the perforations (as it is shown in the
image). Use sixteen 1/4” x 3/4” screws with nut, inserting them
bottom-up
rear rack assembly with the front rack assembly,
the Bracket #1 align the perforations place the bracket
on the inside of the roof rack, using eight 1/4” x 1/2” screws
with lock nuts (Do not tighten yet)
5
Rear Roof Rack Assembly
Central Rail
3/16 x 1/2 “ screw
Frontal Roof Rack Assembly
Align
Bracket #3
1/4 x 1/2” screw
3/16 x 3/4” screw
Bracket Direction
(Do not tighten yet)
Join the
using