AGT INDUSTRIAL AGT-SSEFGC175 User manual

PRODUCT MANUAL
AGT INDUSTRIAL
Skid Steer Flail Mower
Ver.1.1.3
Model:AGT-SSEFGC175

P2
TABLE OF CONTENTS 2/12
TO THE OWNERS 3/12
TABLE OF CONTENTS
SAFETY PRECAUTIONS 4/12
FLAIL MOWER ASSEMBLES 7/12
NOTES 12/12

P3
TO THE OWNERS
GENERAL COMMENTS
Congratulations for having this Flail Mower! Your Flail Mower was carefully
designed and manufactured to give you years of dependable service. Your
Flail Mower will require some minor maintenance to keep it in top working
condition.
Please observe all safety precautions and maintenance procedures as
described in this manual.
BEFORE OPERATION
Thoroughly read and understand the instructions given in this manual before
operation. Refer to the "Safety Label" section, read all instructions noted on
them.
Do not allow anyone to operate his equipment who has not fully read and
comprehended this manual and who has not been properly trained in the
safe operation of the equipment.
SERVICE
Please remember to use only manufacturer replacement parts. Substitute
parts may not meet the standards required for safe, dependable operation.

P4
SAFETY PRECAUTIONS
BEFORE OPERATION
1. The operator must read the operation manual carefully before
installation, operation or maintenance. Improper operation will cause the
machine damage or the operator death.
2. Read all the safe signs and safe declarations. Follow all the professional
safe terms, local laws or the professional directions.
3. Familiar with the Flail Mower about functions, specs and operation.
Replace the to-be-damaged parts in time. Make sure all the hydraulic
installations and couplings connect firmly, and all the safe signs stick on the
suitable positions clearly.
1. Operator should be familiar with all functions of the unit.
2. Make sure all guards and shields are in place and secured before operating
implement.
3. Keep all persons away from equipment and work area.
4. Dismounting from a moving unit can cause serious injury or death.
5. Keep hands, feet, and clothing away from power-driven parts.
6. Detach and store implement in an area where children normally do not play.
Secure implement by using blocks and supports.
IMPORTANT
Always wear proper safety glasses, goggles, or a face shield when
driving pins in or out, or when any operation causes dust, flying
debris, or any other hazardous material.

P5
SAFETY PRECAUTIONS
Operator Safety
►Wear protective clothing and equipment appropriate for the job. Clothing
should be snug fitting without fringes and pull strings to avoid entanglement
with moving parts.
►Prolonged exposure to loud noise can cause hearing impairment or
hearing loss. Wear suitable hearing protection such as earmuffs or earplugs.
►Operating equipment safely requires the operators all attention, Avoid
wearing radio headphones while operating machinery.
Tool Safety
►Inspect entire machine before each use. Replace damaged or worn parts.
►Check for fuel leaks and make sure all fasteners are in place and securely
fastened.

P6
SAFETY PRECAUTIONS
Wear Protective Equipment
►Escaping fluid under pressure can penetrate the skin causing serious injury.
►Avoid the hazard by relieving pressure before disconnecting hydraulic lines
or performing work on the system.
►Make sure all hydraulic fluid connections are tight and all hydraulic hoses
and lines are in good condition before applying pressure to the system.
►Use a piece of paper or cardboard, NOT BODY PARTS to check for
suspected leaks.
►Wear protective gloves and safety glasses or goggles when working with
hydraulic systems.
►DO NOT DELAY. If an accident occurs, see a doctor familiar with this type of
injury immediately. Any fluid injected into the skin or eyes must be treated
within a few hours or gangrene may result.
Transportation and Storing
►Store machine and fuel where fuel vapors cannot reach sour combustion
like, water heaters, electric motors, switches, furnaces, etc.
►Always secure the machine with tie downs or similar restraints when
transporting.
►The machine be stored in a manner that prevents it from falling, rolling or
tipping.

P7
FLAIL MOWER ASSEMBLES
P8P9P7
S/N PART NO. PART DESCRIPTION QTYS NOTE
1 GB/T 5782 Bolt M16*120 2
2 GB/T 97.1 Washer 16 3
3 LM180.27 Bushing 4
4 LM180.25 Bushing for wheel 2
5 LM180.10 Wheel Φ220*75 2
6 GB/T 6182 LOCK NUT M16 2
7 WLF130.4 Axle adjusting sleeve 02 2
8 WLF130.3 Axle adjusting sleeve 01 2
9 JB／T 7940.1-1995 Greaser M8 4
10 WLF130.2 Wheel arm weldment 2
11 DIN 11023 LOCK PIN 6
12 WLF130.1 Wheel fork weldment 2

P8
FLAIL MOWER ASSEMBLES
S/N PART NO. PART DESCRIPTION QTYS NOTE
13 GB/T 5783 Bolt M12*35 14
14 GB/T 93 SPRING WASHER 12 42
15 GB/T 97.1 Washer 12 57
16 GB/T 91 Pin 3.2*22 2
17 GB/T 97.1 Washer 10 22
18 EFGC175.24B Wide fender 1
19 WLF130.6 Shaft bar 1
20 EFGC175.24B Wide fender 15
21 EFGC175.24B Wide fender 1
22 GB/T 5783 Bolt M12*35 14
23 GB/T 6182 LOCK NUT M12 10
24 WLF130.8 Skid shoes weldment ( R ) 1
25 GB/T 5783 Left cover 1
26 GB/T 97.2 Blade axle weldment 1
27 LM180.27 LOCK NUT M12*1.5 28
28 LM180.25 Hammer 28
29 LM180.10 Bolt M12*1.5*50 28
30 GB/T 6183 Skid shoes weldment ( R ) 1
31 WLF130.2 Right cover 1
32 WLF130.1 Bolt M8*16 3
33 JB／T 7940.1-1996 SPRING WASHER 8 11
34 WLF130.3 Washer 8 13
35 DIN 11024 Belt cover 1
36 WLF130.2 Sleeve REACH 04 2
37 GB/T 5597 Small pulley 1
38 EFGC155.31 Big pulley 1
39 GB/T 11544 Belt SPB1016 3
40 GB/T 5783 Bolt M12*50 8
41 GB/T 5783 Bolt M8*25 8
42 WLF130.9 Protection Plate 01 1
43 WLF130.26 Bushing 1
44 M6X1-6X4 Lock nut connector 2

P9
FLAIL MOWER ASSEMBLES
S/N PART NO. PART DESCRIPTION QTYS NOTE
45 WLF130.25 Pipe for grease Φ6*Φ4 1
46 WLF130.24 Tension rollers assemble 1
46-1 WLF130.24.1 Tension plate weldment 1
46-2 WLF130.24-2 Tension Roller 1
46-3 GB/T 276 Bearing 6005-Z 2
46-4 WLF130.24-3 Washer 1
46-5 GB/T 5783 Bolt M12*30 1
47 GB/T 6170 NUT M12 3
48 WLF170.5 FRAME WELDMENT 1
49 JB/T 7940.1 Grease nipple M6 2
50 GB/T 5783 Bolt M12*35 8
51 WLF130.29 Low linkage weldment 2
52 WLF130.22 A Up linkage pin 2
53 GB/T 97.1 Washer 16 4
54 WLF130.18 Up linkage weldment 1
55 WLF130.21A Low linkage pin 1
56 GB/T 7810 Bearing UCFU207 2
57 WLF130.10 Protection Plate 02 1
58 WLF130.30 Coupling 1
59 GB/T 6170 NUT M12 8
60 GB/T 70.1 Hex Bolt M12*45 4
61 GB/T 70.1 Hex Bolt M12*50 4
62 GB/T 6170 NUT M8 2
63 CMGh2025-BFΦSGearbox motor 1
64 GB/T 5783 Bolt M8*55 2
65 WLF130.27 Hydraulic components 1

FLAIL MOWER ASSEMBLES
P10
S/N PART NO. PART DESCRIPTION QTYS NOTE
65-1 LM180.26-1 Connector 01 2
65-2 AS 568 O RING Φ32.92*3.53 2
65-3 GB/T 5862 FLAT FACED COUPLERS G1/2 MALE 1
65-4 GE15LRED Connector 02 6
65-5 WLF130.27-1 Hydraulic hose: Length:2000mm 1
65-6 GE10SRED Connector 03 2
65-7 GB/T 5862 FLAT FACED COUPLERS G3/8 FEMALE 1
65-8 WLF130.27-2 Hydraulic hose: Length:2200mm 1
65-9 GB/T 70.1 BOLT HEX M10*30 8
65-10 GB/T 97.1 Washer 10 8
65-11 WLF130.27-3 Hydraulic hose: Length:2000mm 1
65-12 WLF130.27-4 Hydraulic hose: Length:1200mm 1
65-13 WLF130.27-5 Hydraulic hose: Length:500mm 1
65-14 GB/T 5862 FLAT FACED COUPLERS G1/2 FEMALE 1
65-1 LM180.26-1 Connector 01 2
65-2 AS 568 O RING Φ32.92*3.53 2