Aleko BSW04 User manual

35
8
910
4
5
7
4
5
5
5
5
7
15
15
8
9
10
4
3
3
Swing and Glider Set- BSW04
www.aleko.com

4
3
Figure 1
BEFORE ASSEMBLING: Please read and abide by all Safety Guidelines, and confirm all
necessary parts are included by referencing parts list on page 1.
Step 1. Place together the short curved ends of the Left-Hand Top Leg and Right-Hand
Top Leg and insert as one into the Swing side (closest to the 2 sets of vertical holes) of the
Top Bar (Figure 1).
**Always Make sure to place included washers between fastener head or nut and
adjoining swing set components**
Step 2. Place 1 F1 bolt through the BOTTOM side of Top Bar and use included Allen Key
to hold bolt stationary while tightening nut using Spanner.
Repeat the process by inserting the remaining Top Legs into the Glider side (closest to 2
horizontal holes)
Fig. 2
Step 3. Completely disassemble S1 U-Bolts then place u-shaped bolt through the hole
in the bearing assembly found at the end of the Swing Seat ropes (Fig. 2).
Step 4. Tighten open-ended S1 nut down onto u-shaped bolt, place 1 S1 washer on
each end of the bolt and insert into Top Bar through 2 sets of vertical holes on Swing
side. Ensure washer placement between nuts and Top Bar.
Step 5. Attach F1 closed-end nut to u-shaped bolt and tighten down. Repeat for both
sides of Swing Seat.
4
4
5
5
5
7
7
7
Fig. 3

9
10
15
Step 6. Insert 1 Plain Bottom Leg into both Left and Right-Hand Top Legs, and place
an F2 bolt through the leg junction (See Fig. 3).
Step 7. Attach flat side of Side Stay Bar to the protruding thread side of the F2 bolt,
and apply washer and round-ended cap nut to secure Leg and Side bar assembly.
Step 8. Repeat process for both Swing and Glider sides of swing set.
8
Fig. 4 Fig. 5
Step 1. Slide Glider bracket over glider side of Top Bar and align to the 2 horizontal
holes
(Fig. 4).
Step 2. Attach Glider Bracket to Top Bar using 2 G1 fasteners.
Step 3. Insert 1 G8 Plastic Spacer into the holes on either side of the Glider Handle
Tubes.
Step 4. Attach curved upper bar portion of Glider Handle Tubes to holes on bottom
corner of the Glider Bracket using 1 G2 fastener for each side (Fig. 5).
1
8
8
9
9
Fig. 6
Step 5. Insert tapered segment of Glider Legs into exposed open side of Glider
Handle Tubes, use 1 G6 bolt on either side to attach (Fig. 6).
8
Fig. 7

(See Fig. 7)
Step 6. Insert 1 G9 Plastic Spacer into either side of the holes near the center of the
Glider Legs.
Step 7. Attach the Glider Seat Tubes to either side of the Glider Legs using a G4 fastener
through the set of holes that the G9 Spacer has been installed in.
Step 8. Fasten Glider Seat to Glider Seat Tubes using 4 G6 Fasteners through both sets
of holes on both Seat Tubes. Repeat to assemble both Seats.
Step 9. Use G5 fasteners to secure Glider Footrest to lower holes in Glider Legs
Step 1. Attach Ground Pegs to all 4 Swing set Bottom Legs using P1 fasteners.
Step 2. Place assembled Swing Set in desired location and dig a footing hole,
measuring 12" (30cm) Long x 12" (30cm) Wide x 20" (50cm) Deep, at the base of each
support leg (Fig. 8).
Step 3. Prepare and pour concrete into the footing holes following concrete
manufacturer's instructions. Fully fill footing holes to be level with ground surface.
Step 4. While Concrete is still wet, Angle Ground Pegs toward swingset Top Bar at
roughly 120-degrees, then insert Ground Pegs into concrete footing, making sure
Swingset Bottom Legs do not sink below ground surface (utilize concrete set time
information). Use temporary support made from wood or other material if necessary to
prevent sinkage.
Step 5. Swing Set will be ready for use once concrete is fully set and cured (consult
concrete manufacturer's instructions).
5
5
35 35
Fig. 8