AnyBeam HD301M1-H2 User manual

Function normal. Standby and Power Saving Mode
LED Indicator
LED Indicator 1 remains on
LED Indicator 2 remains on
LED Indicator 1 flashes rapidly
Device Status
Function normal. Power is ON
Function normal. HDMI cable is connected
Function abnormal. Please see the Troubleshooting
Dimensions (W x H x D)
Weight
Approx. 103 x 60 x 19 mm
Approx. 140±10% gram
Operating Temperature 0°C ~ 35°C (32°F ~ 95°F) @50% white chart
Rated Voltage/ Current DC 5V / 1.5A
Speaker:1.0W (Max.)
Imaging Technology
Resolution
Brightness
Contrast Ratio
MEMS Laser Scanning
720P / 60fps (Input)
ANSI 30 lumens ±10% ( equivalent to 150 lumens)
80,000：1
Color Gamut
Throw Ratio
Focus
>150%
1.37
Focus-Free
Input / Output
Audio Output: 3.5mm Audio Jack
Interface: HDMI
Model HD301M1-H2
Note 01: AnyBeam suggests 720p resolution input. Some otherresolutionmight not be projected.
Specifications and Features
Note:
Relationship between the distance from the projector to screen (D) and the width of
projection screen size (W) :D/W=1.37 (Throw Ratio)
MemsLaser Scanning Projector
User Manual
IMPORTANT SAFETY INSTRUCTION
• Do not apply any strong force or shocks to the projector, otherwise damage may
occur.
• Do not use the projector outside the required temperature range (0-35°C/ 32-95°F).
This may cause an unstable display and could lead to damage.
• Do not expose the projector to water or sources of heat.
• Avoid looking directly at the projector laser beam when turned on. The laser beam
might cause damage to the eyesight.
For the figure shown below, determine the image size that can be projected under different
lighting conditions.
User's Instruction
1. The unit has no built-in battery. Please connect the Micro USB interface for power supply.
2. Do not press the jog lever and slide or at the same time while using the projector.
It may result in functional failure or damage to the portable device.
3. There are two major factors WHICH must be considered while using the AnyBeam
•Ambient Lighting
To achieve better projection effect, please draw the curtain and turn off the light.
•Projection Distance
The distance between projector and the screen affects the projection brightness. The
shorter distance, the brighter screen.
Rev. A01 202
Audio Jack
[3.5mm headphone/ speaker jack]
NUT (SCREW)
[UNC 1/4”-20]
Speaker
LED Indicator 2
[HDMI Connection Status]
70”~100”
~2-3m 24”~36”
~1m <12”
~0.3m
Semi Dark [Dimmed Lighting]
Semi-Lit [Home / Office]
Complete Darkness
HDMI Jack
[Note 01]Micro USB Jack
[Power Input 5V/1.5A]
LED Indicator 1
[Power Status]
Lens
Laser radiates from this aperture
Jog Lever
( / / )
LED Indicator 2 flashes every 3 seconds

The color does not look appropriate
( e.g. color bias too red, yellow or green
etc.)
Image jitter ( MEMS work abnormal
due to unknown factors)
1. Check whether the native projected image is output
abnormal.
2. Unplug and plug again the cable from the device to restart.
1. Unplug and plug again the cable from the device to restart.
2. Replace other power adapter (DC 5V/ 1.5A or greater
output), and reconnect the device to restart.
3. Remove any metal or magnetic material from the device,
then unplug and plug it again to restart.
4. Check whether there‘s any source of vibration (e.g.
speaker, vibration will cause abnormal function of
MEMS).
Problem Inspection/ Solution
Loose Micro USB Cable or no
Connection
(LED
Indicator 1: OFF)
Check whether the cable is connected correctly to the power
adaptor (DC 5V/ 1.5A or greater output).
Internal Protected Mode is activated due
to unknown factors
(LED
Indicator 1: blink rapidly)
Unplug and plug the cable to restart the device. If same case
happened, please replace other power adapter (DC 5V/ 1.5A
or greater output), then connect it again.
Standby and Power Saving Mode
(LED
Indicator 1: OFF
LED
Indicator
2: flashes every 3 seconds)
The projector enters standby status
at the specified time
, when
no signal output from the video source device. Please awake
the projector by resuming signal or press the jog lever.
Problem Inspection/ Solution
Loose HDMI Cable (AV I/O)
(LED Indicator 1: remains on
LED Indicator 2: OFF)
Check whether the HDMI cable is connected correctly or
loose in both input/ output terminal.
No Signal output from the video sources
(LED
Indicator 1: remains on
LED
Indicator 2: OFF)
Check whether the video source (Output) is sending the
content to the projected device (Input) correctly.
Support：
•User Manual
Product Instruction and Troubleshooting are included.
•Technical Support
If there is any question, please refer to the user’s manual first. If the issue still exits after
conducting default settings, please inquire and contact the service center for help from
below link.
Official Website: www. Anybeamstore.com
Email: [e-mail]
Tel: [phone]
Warranty：
•Limited Warranty Period: 1 year
AnyBeam warrants its Product(s) under normal use during the warranty period. (Self- assembly/
disassembly/ missuses are not included)
•For return your item, if the device is damaged, worn, scratched, stained or so due to mistaken usage
of assembly/ disassembly, you will be responsible for paying for your own shipping costs and
maintenance charges for returning your item.
Problem
Troubleshooting 1
No images are projected
Troubleshooting 2
The image is not projected properly
(NO SIGNAL sign shown only)
Troubleshooting 3
Image Display Error
Troubleshooting 4
Built-in Speaker / Audio Problems
Problem Inspection/ Solution
The image is flickering or blurred Hold down the jog lever for 3 seconds to enter the OSD
mode. Select [Sharpness] to adjust.
Unexpected frame color (green, red or
blue etc.) shown in the Margin of left/
right side of the display or word
Hold down the jog lever for 3 seconds to enter the OSD
mode. Select [Green/ Blue Alignment] to adjust.
Partial area blurred or color fringing
appeared in the display Make sure the lens is clean with no dust and check again.
Image distortion appeared and could not
project correctly AnyBeam suggests 720p resolution input. Some other
resolution may not be projected
Other abnormal Status of projected
image Unplug and plug again the cable from the device to restart,
and check whether the problem is solved.
Inspection/ Solution
There is no Sound Check video source to make sure the volume is turned up
and the audio content is not mute.
Slide the jog lever to ← or → to check the volume level of
the projector.
Unplug and plug again the cable from the device to restart,
and check the problem is solved.
Other abnormal Status of Sound
Silent Mode is selected
Troubleshooting 5
Connected Speaker / Audio Problems
Problem
Specific speakers may not output audio
properly
Hold down the jog lever for 3 seconds to enter the OSD mode.
Select
[AUDIO SOURCE SETTING/ LINE OUT] to force
the audio to outputfrom the connected speakers.
Inspection/ Solution

Keystone, Flip, Brightness, Sharpness, Green Alignment And
Blue Alignment
On-Screen Display (OSD)
Operation Instruction
1. Jog Lever ( /ENTER/ ) Function Instruction
2.Main Menu
3.Display Adjustment
4. Color Alignment
5. Audio Source Setting
6. Language Setting
Note：
1. The effect of the volume adjustment varies from the connected device.
2. Hold down the jog lever for 3 seconds while at the position to make
switching between OSD and general display mode.
Language Setting
Slide the jog lever to or to select and press the jog lever while at the
position to confirm the language. Then slide the jog lever to the
option “ RETURN” and then press the jog lever while at the position
to back to the MAIN MENU.
Sub-Menu of Factory Reset
KEYSTONE
FLIP
BRIGHTNESS
SHARPNESS
GREEN ALIGNMENT
BLUE ALIGNMENT
AUDIO
SOURCE SETTING
LANGUAGE [
語言設定]
FACTORY RESET
繁體中文
简体中文
ENGLISH
日本語
返回
[RETURN]
Rev. A01 202
Jog Lever ( /ENTER/ ) Function Instruction
Mode Operation
Adjusting the volume
Slide the jog lever to or directly to adjust the
volume.
：Volume up ／ ：Volume down
OSD Menu
[Main Menu, Sub
-menu]
Hold down the jog lever for 3 seconds while at the
position to display the menu of the projector.
1.
Slide the jog lever to or to move to the
next or previous item.
2.
Press the jog lever while at the
position with the desired item highlighted to
enter the sub-menu.
3.
Hold down the jog lever for 3 seconds while
at the position to return to the
display mode.
Image Description
Slide the jog lever to or to select
and then press the jog lever while at
the position to confirm.
Image Description
Click
the jog lever while at position to adjust
Remark:
There is a bar on the bottom right corner
which shows the status
Click
the jog lever while at position to adjust
Remark: There are bars on the bottom right corner which
show the status
Press the jog lever while at the position to
SAVE
Press the jog lever while at the position to back to the
MAIN MENU
Audio Source Setting
(It is only required to be adjusted when the audio output does not work properly)
Image Description
AUTO
DETECT (AnyBeam’s default setting)
Choose
this when using the built-in speaker
LINE
OUT
Specific
speakers may not output audio properly.
If you encounter this issue, please choose
[LINE
OUT
]to force the audio to output from the
connected speakers.
Note：
1. When adjusting [Sharpness], please mind the change of the image’s sharpness.
After the adjustment is completed, please save the settings.
2. When adjusting [Green/Blue Alignment], please mind the color change of the
checkerboard image’s edge. When there is no obvious color difference, please
save the setting.
Main Menu