Arena Luci PROMO 5 LED Elite User manual

PROMO5LEDElite
User'sManual
LEDgoboprojectorwithrotationfeature
PRF0150W

2/8
PROMO5LED
This instruction manual contains important
information about the installation and use of the
projector. Please read and follow these
instructionscarefully.
The security of this device is guaranteed only
with the proper use of the following instructions,
thereforetheymustbekeptcarefully.
Never install the device in locations easily
accessiblebypeoplewhoignoretheexistenceof
thisuser'smanualandsafetyinstructions.
Disconnecttheunitfromanypowersupplybefore
attempting any operation in contact or inside the
unit,andwhennotinuse.
It is essential that each device is correctly
earthedandthatelectricalinstallationconformsto
all relevant standards. Never supply the unit
withouttheearthlink.
Prior to connect the unit to the mains supply,
check the output voltage fits the technical
requirementsonthelabel.
Never let the power cord come into contact with
othercables.
Nevertouchtheelectricalcontacts,eitherdirectly
withyour fingers,orindirectly bymeansofsharp
ormetalobjects.
Makesurethatcablescannotcausetriphazard.
Donotattempttodismantleandmodifytheunit.
Due to the high technological level of this unit,
anyservicemaintenanceshouldbeperformedby
specialisedoperators.PleasecontactyourArena
Lucidealerforanyoperation.
Alwaysensurethatthestructuretowhichyouare
attachingtheunitissecureandisabletosupport
theweightofeachunit.
Always make sure you are using a safety chain
connectedtotheunit.
Do not allow contact with water or any other
fluids,ormetallicobjects(IP40).
Do not install the projector in areas of high
humidity.
Avoidinstallingtheunitclosetoheatsources.
Neverleanthepowercordonhotunitsurfaces.
Allowed to be mounted directly on inflammable
surfaces.
Keep a minimum distance of 3m between the
deviceandtheilluminatedsurfaces.
Avoid direct exposure to the light from the lamp.
Thelightluminanceisharmfultotheeye.
Installtheunitwhereitcanbeeasilyaerated.
Avoidobstructionofin/outvents.
Do not install the luminaire on deformed or
damagedceilings.
Thelightingapparatusmustbeusedonlywithits
protectiveshield.
Contact your Arena Luci dealer if the protective
shieldisvisiblydamagedtothepointatwhichits
effectiveness is diminished, for example by
becomingcrackedordeeplyscratched.
To ensure the reliability of the projector it should
bekeptclean.Thelensandfiltersshouldalsobe
regularly cleaned (at least once every six
months)tomaintainanoptimumlightoutput.
Do not use any solvent based cleaning agents.
Useonlyasoft,dryantistaticcloth.
Theinstallation ofLEDmodules(includingpower
supplies) should be done according to current
technical rules and regulations. The installation
shouldbeperformedonlybyaqualifiedoperator.
Avoid contact with either corrosive agents or
humidity and moisture on delicate elements:
damages from corrosion are not refunded as
componentdefects.
WARNINGS
Please note that as part of Arena Luci's ongoing commitment to continuous product development,
specifications are subject to change in the course of product improvement without notice.Arena Luci is not
responsiblefordamagesresultingfromimproperordifferentusethanexpected.

3/8
USER'SMANUAL
BEFORESTARTING
Remove the product from the shipping carton,
checking that all the components supplied are
presentinthe box. Refer to the following packing
list to check which components must be present
in the packaging. If any component is missing or
damaged, contact your Arena Luci dealer
immediately.
n°1projectorPROMO5LEDElite
Before starting the installation of your product
make sure that there are no evident damages
caused by transportation. In the event that the
projectorisdamaged,donotplugitinanddonot
attempt to use it until you contacted your Arena
Lucidealerforassistance.
INSTALLINGTHEPROJECTOR
Attachtheprojector by means of the central hole
diameter 12mm on the fork; for suspended
applications,youmustalsofixtheprojectorwitha
safety chain securing it to the support structure
and the ring arranged on the side panel of the
projector. It is also possible toremoveand rotate
the fork on the bottom side of the projector for a
mounting on tripod, for example, when it is
necessary to install the rain cover, accessory
availableonrequest.
Loosen the side knob to adjust the tilt of the
projector (+55° / 55°); once positioned, tighten
theknobfirmly.
Theprojectormustbefixedonasuitablesupport
which remains stable during operation. Always
makesurethestandorstructuretowhichyouare
settingtheprojector issecureandisable tobear
theweightof10kgofeachunit,plus3.3kgforthe
raincover.
POWERSUPPLYMAINS
Disconnectthemainsvoltagefromthesystem.
Connect the power cord to the mains supply,
paying attention to the voltage and frequency
indicatedonthelabel.
Respect the LNE polarity indicated on the
terminals (color brown = L, blue = N, yellow /
green=E).
It is essential that each projector is correctly
earthedandthatelectricalinstallationconformsto
all the standards of good practice and safety
regulations.
The projector does not have builtin on/off switch
andturnsonimmediatelywhenpowerissupplied.

4/8
PROMO5LED
Itisrecommendedthattheprojectorisconnected
tothemainsviaaproperswitch,sothatitcanbe
turnedonandoffindividually.
Caution
Itisimportantthattheground connection of each
projector is run according to the rules in force.
Thepowerabsorptionoftheprojectoris160W.
GOBOHOLDER
Disconnectthemainsvoltagefromthesystem.
The gobo holder can be accessed by removing
the top cover, after unscrewing the Allen screw
fromtherearpanel.
Oncethecover has been removed, you will have
access to the internal compartment. To insert a
gobo in the motorized assembly, unscrew the
Allen screw and remove the assembly from the
supportframe.
In the front side of the gobo holder you can see
the 12V ac motor, in the rear side there are the
gears. Two housings are available for gobos of
different diameters: the larger one can mount a
70mmdiametergobo,thesmalleronecanmount
a51mmdiametergobo.Inbothcases,theimage
canhaveamaximumdiameterof48mm.

5/8
USER'SMANUAL
Remove the retaining spring ring and insert the
gobo, taking care to keep the dichroic coating
towards the rear sideof the gobo holder: this will
avoid scratching the image when the spring is
removedtoreplacethegobo.
Insert the retaining spring ring all the way down
intothehousing,inordertofirmlylockthegobo.
Mountthegoboholderinsidetheprojector,onthe
supportframe,matchingtheholderhookswiththe
frameopenings.
Finally slide in the top cover and fix the Allen
screwtotherearpanel.
OPERATION
By supplying voltage to the projector, the LED
source turns on by projecting the image of the
gobo; you can turn the gobo rotation on and off
usingthebuttonswitchlocatedontherightsideof
the rear panel of the projector: each time you
presstheswitchtherotationisalternatelyenabled
anddisabled.

6/8
PROMO5LED
ZOOM/FOCUSADJUSTMENT
Zoom of the light beam and focus of the image
are obtained using the 2 knobs located on the
rightsideoftheprojector.
The beam spread can be adjusted from a
minimum of 20° (handles apart, see fig. A) to a
maximumof40°(handlestogether,seefig.B).
RAINCOVER
The optional rain cover kit for outdoor installation
(code COVER150) consists of two forks and a
cover which, once fixed, almost completely
encloses the projector, to protect it reasonably
fromanormalprecipitation.
However,itisadvisabletoevaluatetheintensityof
the atmospheric phenomenon, also in relation to
air currents that could bring water into the
ventilation slots, so as to decide to switch off the
applianceandavoidshortcircuits.
To be able to install the rain kit, the projector's
yokemustbeinthebottomside.
Mount the two forks at the two ends of the
projector,onthetop.Thetwoforkshavetwoholes
oneachside,withdifferentdiameterssoastobe
fixedonlyintheexactorientation.
On the left and right sides of the projector there
arethreadedinsertsusedtofixtheforks.Usethe
M4x10andM6x12Allenscrewsprovidedtofixthe
forkstotheprojector.
Position the rain cover over the forks, matching
thefixingholes of the cover with the holesinthe
forks. The side with the opening must be in
correspondence with the lens of the projector.
ScrewthecoverbymeanofthetwoM6x16Allen
screwsprovided.

7/8
USER'SMANUAL
Assemblingtheraincover

8/8
PROMO5LED
WARRANTYCONDITIONS
The unit is guaranteed for 24 months from the
date of purchase against defects in workmanship
ormaterialsthatcomposeit.
This warranty does faults due to incorrect or
improperuseofthedevice.
The warranty is immediately void if the unit has
been tampered with or opened by unauthorized
personnel.
The warranty provides, at the discretion ofArena
Luci,repairorreplacementoffaultyequipment.
The serial number and model of the device are
required to obtain information or assistance from
the dealer. We invite you to transcribe them in
time: for any request of information or services,
thiswillresultinaquickandeffectiveoperation.
CERULES
The device meets the essential requirements of
the Directives LVD 2014/35/UE, EMC
2014/30/UE, RAEE 2012/19/UE, RoHS
2011/65/UE, Ecodesign 2009/125/CE reg. (UE)
1194/2012, Energy label 2010/30/UE reg. (UE)
874/2012 reg. (UE) 518/2014, GPSD
2001/95/CE.
Warnings
DisposalofOldElectrical&Electronic Equipment
(applicable in the European Union and other
European countries with separate collection
systems).
The product shall not be treated as
householdwastebutmustbehandedoverto
the applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is correctly
disposed, you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling. The recycling of
materialswillhelptoconservenaturalresources.For
more detailed information about recycling of this
product, please contact your city office, your
householdwastedisposalserviceoryoursupplier.
ArenaLucisrlviaSvizzera12/1446042CastelGoffredo(MN),Italy
Tel.+390376782411Fax+390376780973
www.arenaluci.com[email protected]
Powersupply
Powerconsumption
Source
ColourTemperature
Luminousflux
Beamaperture
Connection
Material
Colour
Insulationclass
Weight
Dimensions
Protection
AmbientTemperature
Suitabletobefittedonnormallyinflammablesurfaces
Appliedstandards
230VAC50Hz
160Wmax
COBLEDmodule,interchangeable
5500K.CRI>80
11200lm
Manualzoom20°÷40°
2P+Tpowersupplycable
Aluminiumandsteelplate
Epoxypowderpaintfinish,black
I
10kgprojector3.3kgraincover
423x215x227mm(body)674x333x237mm(raincover)
IP40
From20°Cto+45°C
TECHNICALSPECIFICATION
PRF0150WENR0|12/2017
Table of contents