Artec Mini tracker 506 User manual

Mini Tracker 506 User Manual

Care and Maintenance

(a) Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that

will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to

dry completely before replacing it.

(b) Do not use or store the device in dusty, dirty areas. Its moving parts and lectronic components can be

damaged.

damage batteries, and warp or melt certain plastics.

(d) Do not store the device in cold areas. When the device returns to its normal temperature, moisture can

form inside the device and damage electronic circuit boards.

(e) Do not put Master and Slave at same place in case of this set is unable playing functions to guard your

valued goods.

(f) This product only assists to provide the warning alarm for reminding the user. It does not guarantee to

prevent steal or rob by personal safety and property if any urgent need. This product does not guarantee

any damage of personal safety, property, material or the information loss, or other related loss.

(g) We reserve the right in changing the specification of the hardware and software designs to manuals at

any time and without prior notice. Informationin this document is subject to change without notice.

(h) This product operational temperature is between 0 °C ~ +55 °C. Storage temperature is between -10 °C~

+60 °C.

Warning: Do not put the battery into the fire or heat resource. It will be cause dangerous or even explosion.

(a) Do not attempt to open the device other than instructed in this guide.

(b) Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine

mechanics.

(d) Do not paint the device. Paint can clog the moving parts and prevent proper operation.

Warning

Caution

Care and Maintenance

Recycle: The Battery provided in this product should be recycled to protect the local environment.

Please contact with local recycle department for detail.

FCC Certifications

Federal Communication Commission Interference Statement

This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy, if installed and used not in accordance with the instructions, may cause harmful interference to radio

communications. However,there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2)this device must accept an interference received,

including interference that may cause undesired operation.

FCC Caution: Any changes or modifications are not expressly approved by the party responsible for

compliance which could void the user's authority to operate this equipment.

FCC ID Master: WMPM06A01

Slave: WMPS05A01

EU Declaration Conformity

This product is carrying the CE-Mark in accordance with the related European Directives.

(e) The working range, alarm range, searching and detection are depends the terrain environment because

of radio wave efficiency.

(f) If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder

alarm sound.

(g) If you want to apply this product during the flight trip, please comply with the flight safety law according to

each country.

Master

Front Back

Left direction

Distance indication

Signal indication

Search button

LED light button (Mute distance

melody button at search mode)

Power on

(Standby)

Power off

(Sleeping)

Battery cover

Hanging hole for

strap

Overview

Signal indication

Slave

Front Back

Hanging hole for strap

0 m 100 m

8~16 m

LR 1

2.4GHz ISM2.4GHz ISM

130 × 2

19x28x7.5 mm

8~16m

Alarm

Trident

Direction

Sleeping

Mode

23x46x8 mm

LR 1130 × 2

Alarm

Master

Slave Slave

Alarm

Master Slave

Frequency

Battery

Switch

Size

Button 2 buttons

ON / OFF

Working Method

Specification

Master

The Battery Installment

1. Open from the fillister on the

bottom of housing or curve side

by your nail, like open shell.

2. Put 2pcs batteries into.

*** Make sure the installment direction of

positive (+) & negative (-) of battery are

followed up the drawing showed on the

inside of back battery cover.

3. Set back the battery cover.

Slave

1. Press the clip on battery cover then push

backwardly.

2. Put 2pcs batteries into.

*** Make sure the installment direction of

positive (+) & negative (-) of battery are

followed up the drawing showed on battery

cover.

3. Set the battery cover back.

Beep

Getting Started

For the first time use, please set the battery into Master according to above

battery installment .

Switch to power on

Pull out

Plastic isolation Place two devices no

more than 10 cm apart.

Signal indication

Signal LED ON for re-linking.

Distance

indication

Re-link successful!

Master shows the

distance with Slave via

LED and melody (beep).

Beep

If Master can't link with

Slave, it will beep once

every few seconds.

Caution

1 2

Press Search button

2~3 seconds

Start to detect the location

of Slave.

Near Far

1.) LED light: more

closer, more lights.

2.) Search melody: more

closer, more rapid.

North

South

East

West

2 Distance LEDs

3 Distance LEDs.

The strongest

signal direction !

Turn to different directions

for signal comparison

One Distance

LED only

2 Distance LEDs

Go the way of the

strongest signal

direction to find out

Slave.

321

Beep

Mute searching melody from Master. Listen beep sound

from Slave to assist short range searching.

Press & hold the LED

light button

Stop the melody

and light up the

torch LED

Listen to the beep

sound from Slave

Stop

searching

Back to Standby mode

Signal LED flashes every

second for re-linking

Signal

indication

Press Search button

2~3 seconds

Error indication - whole direction LED goes off but

signal LED lights up 3 seconds then displays new

searched distance.

1.) Search from correct direction to wrong direction

2.) Over pass

0～100 m

East

North

East

Signal indication

Distance LED goes out all

lights suddenly and only flash

Signal LED with beep sound

LED displays new

searched distance

Go back to original search

direction or location

Location:

North

Go to the

wrong direction

Original searching

(Right direction)

3 seconds

later

Searching Example

Suggestion

1 2

Alarm

Beep

Over 8~16 meter.

Come with beep!

Stop alarm (beep) if both devices

comes within 8 meter again.

Signal

indication

When Slave and Master are over 100

meter or lose signal

Caution

Slave flashes half minute to

wait for re-linking

No linking then into sleeping

modeand stop flash

Switch to sleeping mode

Sleeping

Under Standby mode Stop signal to Slave

No linking then into sleeping mode and stop flash

Slave flashes half minute to wait for re-linking

Switch the button to

section 0 (OFF)

1 2

Switch the button to

section 1 (ON)

Signal LED ON for re-linking

Available for distance within

100 meter

Re-link successful!

Master shows the distance

between Slave via LED

and melody (beep)

Distance

indication

Beep

Can't get signal from Slave.

Signal LED flashes each second & comes with beep.

(Slave maybe out of working range 100 meter, or no power.)

Beep

Re-link / Wake up

Low Battery

If this kit is under low battery stage, it may cause

abnormal display to alarm, beeps or non-working to

confuse actual working stage.

Please change new battery as soon as possible.

1 beep sound every 20 seconds continuously.

スターター

Suggested setting place

Wrong

holding

Correct

holding

*** Do not cover the top side of Master.

Master Slave

Suggested setting place

91E-02B2-U50G10

Table of contents

Artec Mini Tracker 506 User manual