Autel Smart Controller SE User manual

Quick Start Guide


1. Disclaimer
To ensure safe and successful operation of your Autel Smart Controller
SE (hereinafter referred to as the "controller"), please strictly follow the
operating instructions and steps in thisguide.
If the user does not abide by the instructions, Autel Robotics will not be
responsibleforany product damage orloss in use, whether direct or indirect,
legal, special, accident or economic loss (including but not limited to loss of
profit) and does not provide warranty service. Do not use incompatible parts
or use any method that does not comply withthe official instructions of Autel
Robotics to modify the product.
The safety guidelines in this document will be updated from time to
time. To ensure you get the latest version, please visit the official
website: https://www.autelrobotics.com/
2. Battery Safety
The controller is powered by a smart lithium-ion battery. Improper
use of lithium-ion batteries can be dangerous. Please ensure that the
following battery usage, charging and storage guidelines are strictly
followed.
Note
• Only use the battery and charger provided by Autel Robotics. It
is forbidden to modify the battery assembly and its charger or
use third-party equipment to replace it.
• The electrolyte in the battery is extremely corrosive. If the
electrolyte spills into your eyes or skin accidentally, please rinse
the affected area with clean water and seek medical attention
immediately.
3. Precaution
1

2
4. Item List
NO DIAGRAM ITEM NAME QTY
If used improperly, the aircraft may cause injury and damage to
people and property. Please be cautious while using it. For details,
please refer to the aircraft’s disclaimer and safety guidelines.
• Before each flight, make sure that the controller is fully
charged.
• Ensure the controller antennas are unfolded and adjusted to
the appropriate position to ensure the best possible flight
results.
• If the controller antennas are damaged, it will affect the
performance. Please contact the after-sales technical support
immediately.
• If the aircraft is changed due to damage, it needs to be relinked
before use.
• Make sure to turn off the aircraft power before turning off the
controller each time.
• When not in use, make sure to fully charge the controller every
three months.
• Once the power of the controller is less than 10%, please
charge it to prevent an over-discharge error. This is caused by
long-term storage with a low battery charge. When the
controller will not be in use for an extended time, discharge the
battery between 40%-60% before storage.
• Do not block the vent of the controller to prevent overheating
and diminished performance.
• Do not disassemble the controller. If any parts of the controller
are damaged, contact Autel Robotics After-Sale Support.

3
5. Overview
Documentation
(Quick Start Guide)
󾙘1pc
Chest Strap
Spare Control Sticks
󾙓
󾙔
󾙕
󾙖
󾙗
1pc
1pc
1pc
2pcs
1pc
Controller
Power Adapter
USB-C Cable
The Autel Smart Controller SE is integrated with a 6.4-inch touch
screen which boasts a 2340x1080 pixel resolution. The controller f
can transmit a liveHD view from the aircraft[1] at a distance of up
to 15km[1] (9.32 miles). The controller uses the Android operating
system and supports Wi-Fi internet connection,Bluetooth and
GNSS. Users can download third-party APPs.
The built-in battery has a capacity of 1900mAh, providing a

6. Diagram
1.Left Control Stick
2.Gimbal Pitch Dial
3.Customizable Button
4.Chest Strap Hook
5.Air Outlet
6.USB-A Port
7.USB-C Port
8.Micro-SD Card Slot
9.HDMI Port
10.Record/Shutter Button
11.Zoom Control Wheel
12.Right Control Stick
4
4 5 6 9
8
11
310
2
4
112
maximum operating time of about3 hours[2].
[1] In an actual flight environment, the maximum transmission
range may be less than this nominal distance and will vary with
the interference strength.
[2] The above-mentioned operating time is measured in a lab
environment at room temperature. The battery life will vary in
different usage scenarios.
7

5
20.Speaker Hole
21.Tripod Mount Hole
22.Air Inlet
13.Power Button
14.Antenna
15.Microphone
16.Touch Screen
15
14
19
17
18
16
17.Auto-takeoff/RTH Button
18.Pause Button
19.Battery Level Indicator
25
21
20
24
23
22
13
23.Handle
24.Sticks Storage Slot
25.Battery Case

7. Charge the Battery
7.1 Check the Battery Level
Press the power button to check the battery level.
7.3 Charge
Connect one end of the USB-C cable to the USB-C interface at the
top of the controller, and the other end to power adapter. Plug the
power adapter into AC power outlet (100-240V).
7.2 Power On / Off
Press and hold the power button for 2 secs to turn on and off the controller.
6
1 light solid on: Battery≥25%
Battery Level Indicator (non-charging state)
2 lights solid on: Battery≥50%
3 lights solid on: Battery≥75% 4 lights solid on: Battery=100%
1 light solid on: Battery≥25%
Battery Level Indicator (while charging)
2 lights solid on: Battery≥50%
3 lights solid on: Battery≥75% 4 lights solid on:Battery=100%

8. Set Up the Controller
8.1 Install the Sticks
The sticks storage slots are located on the back of the controller.
Please take out the sticks and screw them into the corresponding
bases.
7
Note
LED indication light will blink while charging.
Only use the battery and charger provided by Autel Robotics.
Recharge the battery at least every 3 months to prevent over
discharging. The battery depletes when stored for an extended
period.

8.2 Adjust the Antennas
Unfold the controller antennas and adjust them to the optimal
angle. The signal strength varies when the antenna angle is
different. When the antenna and the back of the controller are at
an angle of 180° or 270°, and the antenna surface is facing the
aircraft, the signal quality between aircraft and controller will
reach the optimal condition.
9. Pair the Frequency
8
󾙓󾙚󾙒
󾙔󾙙󾙒
Note
To avoid controller signal interference, please do not use other
communication equipment with the same frequency band at the
same time.
During operation, the App will prompt the user when the image
transmission signal is poor. Adjust the antenna angles according
to the prompts to ensure the controller and aircraft have the
best communication range.
1. Press (short press) the linking button next to the USB port on the
right side of the aircraft body to put the aircraft into the linking
mode.
2. Power on the Smart Controller and run the Autel Explorer app,
enter the mission flight interface, click the gear icon in the upper
right corner, enter the settings menu, click "remote control -> data
transmission and image transmission linking> start linking", wait a
few seconds until the data transmission is set correctly and the
linking is a success.