Blinder M27 X-TREME User manual
USER MANUAL
M27 & M47 X-TREME
TICKETS
NO
MORE
SPEEDING
USER MANUAL CONTENTS
First start-up of the system 3
Installing Guide 4-5
•Mounting the transponders
•CPU –Electrical guide
How to operate the Blinder 6-7
•Parking Mode
•Multifunction Mode
•Use the parking assist with caution
Free Software Updates 7
Speeding Ticket program 8
Product Warranty 8
Warranty Services 8
Product registration 9-10
Products 11
Contact Blinder 12
CONTENT
ONLINE PRODUCT SUPPORT
Please check for the latest new help les
and additional product information on
www.blinder.dk.
3
BLINDER M27/M47 USER MANUAL
BLINDER M27/M47 USER MANUAL
Thank you for purchasing the advanced Blinder M27/M47 Multi Purpose System which contains func-
tions, such as, Parking-Assist, Garage Door Opener, Gate & Driveway Light Activator and Laser-Protection.
FIRST STARTUP OF THE SYSTEM
As a top performing product the Blinder 7-Series will at rst start-up, automatically initialize all con-
nected transponders and in cases where the CPU contains a dierent or newer software revision, auto-
matically update all connected transponders.
The following steps will occur during an automatic software update
•Once installation of the system is complete, activate the mode switch to position II for at least 1 min-
ute.
•The Buzzer & LED will indicate the updating process by beeping / ashing with fast intervals.
•Between updating of each single transponder there will be a short break in beeping / ashing.
•This process will be repeated until all transponders are fully updated, witch means two times for M27
and four times for M47. Once all transponders are successfully updated, the system will ash RED and
beep two times.
•To start-up the system correctly after updating, switch to position OFF and then back to the mode you
wish to use. The system is now ready to perform its function.
Interrupted during the automatically software update
If the system is interrupted during the updating process, you may end up with a non-working system. In
this case, it’s possible to download Blinder’s repair software to reset the system. For further information
please visit our website at www.blinder.dk.
IMPORTANT!
Do not turn o the power for at least 1 minute during the rst start-up process.
INSTALLATION GUIDE
Level to the road ✕
The detector is placed in this
end of the transponder and
should be placed furthest from
the center of the vehicle.
The wire
Wire
USEFUL TIP FOR OPTIMAL PERFORMANCE
To obtain optimal performance, it is important to install all
transponders with the build in detectors oriented outwards!
Detector
1. MOUNTING OF TRANSPONDERS (Professional installation is recommended)
It’s very important to mount all transponders carefully since the transmitting and receiving infra red laser
beam will not pass through any objects, it’s essential that all transponders have an unobstructed view of
the road, pointing straight ahead, mounted horizontal and parallel to the road surface and driving direc-
tion. Please see illustration below.
1.1 BEST LOCATION
Before installation, determine carefully the best location for the transponders. On both the M27 and M47
system mount one transponder on each side of the front or rear license plate with a distance between the
two transponders of 50 to 60 cm / 20 to 24 Inch. For the M47 which is designed for bigger SUV’s, mount
the two additional transponders in the upper grill close to the headlights. For further info please visit www.
blinder.dk.
1.2 MOUNTING BRACKETS
Fit the mounting brackets and transponders together by using the short version of enclosed tting screws.
WARNING! DO NOT use the enclosed longer drilling screws to t the bracket and transponder together, as
it will damage the inside electronic and will NOT be covered under the warranty. The longer screws are to
be used to fasten the brackets to the car ONLY.
1.3 HORIZONTAL LEVEL ANGLE
Mount the transponders making sure that each transponder is horizontally level to the road and parallel
to the driving direction. To ensure a perfect horizontal level angle, t the enclosed spirit level in one of the
cylindrical holes in the front of the lens. After carefully adjusting the angle, tighten the screws on each side
of the transponders. Check the level angle and replace the spirit level. Mount the enclosed plugs with the
small curved edge on each plugs facing outward.
5
INSTALLATION GUIDE
2. CPU
Locate a suitable place for the CPU inside
the cars’ interior. The CPU may not be
located in the engine compartment be-
cause of heat risk and moisture. Connect
all transponders to the CPU indicated by
the numbers 1 to 4.
3. BUZZER AND LED
Locate a suitable place for the Buzzer
& LED, connect the cable to the CPU
marked “Alert”.
4. THE THREEPOSITION SWITCH
Locate a suitable place for the 3-position
mode switch, drill a hole of 20mm, draw
the cable through the hole and connect
it to the CPU.
5. CONNECTION TO AUDIO MUTE
The blue wire from the CPU can be con-
nected to the Car Stereo audio mute and
will automatically mute the Car Stereo
when the Blinder alerts in multifunction
mode (See the Car-Stereo Manual).
6. CONNECTION TO GROUND
Connect the black wire from the 3-posi-
tion switch to a solid ground (-).
7. CONNECTION TO POWER SUPPLY
Connect the red wire (+) from the 3-posi-
tion mode switch to a solid switched
12-volt.
3
7
65
4
(Black) Ground
(Red) 12 Volt
1234
CPU
(Blue) Audio Mute
Alert
3-position switch
1. Parking Mode
0. Power O
2. Multifunction Mode
USB port
(to PC)
1
2
1
HOW TO OPERATE THE BLINDER
HOW TO OPERATE THE BLINDER M27 / M47
Use the 3-position switch to select the operating mode you wish to use.
The system can switch between position # I, # 0 and # II. After a mode switch, the system will respond
with sound / light as explained below. Sound / Light features are adjustable in the Blinder Update Soft-
ware.
SWITCH POSITION # 0 SYSTEM OFF
LED OFF
Sound OFF
Always use the position OFF if you want to disconnect any part of the system, during software updating,
or for other reasons.
SWITCH POSITION # I PARKING ASSIST MODE / FLASHING GREEN
(At start-up or mode switch)
LED 1 Red ash
Sound 1 Beep
This mode turns your Blinder into a Parking Assist System and the two color LED changes to ashing
GREEN. In Parking Assist mode the system will respond by increasing sound volume of 3 levels when the
car is approaching an object. We strongly recommend that you get yourself accustomed to the systems
behaviour before using on a public road.
USE THE PARKING ASSIST WITH CAUTION!
The Blinder system will detect dierent objects with uneven eectiveness depending on the color of
the object. Bright objects reect much better compared to dark, and will therefore allow earlier detec-
tion and warning. The Blinder system will not detect and alert on glass or other transparent materials.
Be especially cautious when parking close to shop windows and similar transparent objects. Always be
aware and watch for hidden objects near the car such as children and animals that may not be detected
by the system. Please use common sense and visually survey in all parking situations and do NOT rely
100% on the Park Assist feature.
IMPORTANT TO KNOW!
While the system is in parking mode, the system will NOT respond to any incoming laser pulses!
7
SOFTWARE UPDATE
SWITCH POSITION # II MULTIFUNCTION MODE / CONSTANT GREEN
(At start-up or mode switch)
LED 2 Red ashes
Sound 2 Beeps
This mode turns your Blinder system into a Multifunction system and the two color LED changes to
constant GREEN. In this mode the system will detect and respond to all selected incoming 905nm laser
pulses. At laser alert, the LED changes from constant GREEN to RED and the Buzzer alerts simultaneously
as long as selected laser pulses receives. To prevent interfering with 905nm laser based systems, such as
police speed equipment, the Blinder system will automatic stop transmitting after 7 Sec. and go into a
60 Sec. timeout/sleeping mode. After the 60 Sec. timeout/sleeping mode, the system goes automati-
cally back to active mode, indicated by a short single beep / RED ash. The limited transmitting time
feature is adjustable in Blinder Update Software. For further info please visit: www.blinder.dk
SOFTWARE UPDATE
1. Download the Blinder Update Software to your laptop or desktop PC at www.blinder.dk
2. Turn OFF the power on the Blinder system.
3. Connect a USB cable between the Blinder CPU and a laptop or PC. When updating the CPU
using a PC, remove the CPU from the car and connect it to the PC.
4. Select the le in the Blinder Update Software you wish to upload to the Blinder CPU. Click on the CPU
Firmware button and the CPU will be updated within 1 minute. DO NOT disconnect the CPU during
the updating.
5. Disconnect the USB connection between the CPU and laptop/PC. Reinstall the CPU in the car, if updat-
ing has been made on a PC.
6. Activate the mode switch to position II for at least 1 minute and the CPU will start to update all tran-
sponders one by one. The Buzzer / LED will indicate the updating process by beeping / ashing with
fast intervals. Between updating of each single transponder there will be a short break in beeping /
ashing and the process will be repeated until all transponders are fully updated. (M27 two times, M47
four times) Once all transponders are successfully updated, the system will ash RED and beep two
times.
7. To start-up the system correctly after updating, switch to position OFF and then back to the mode you
wish to use. The system is now ready to perform its function.
To ensure keeping the Blinder system fully updated, please visit our website at www.blinder.dk fre-
quently to look for new software revisions and stay protected against new laser speed equipment in
the future. The Blinder Update Software furthermore allows personal customized settings as limited
jamming time and access to new product features.
SPEEDING TICKET PROGRAM
SPEEDING TICKET PROGRAM (USA ONLY)
Blinder USA oers a Speeding Ticket Program. Please sign up at www.blinder.dk
BLINDER PRODUCT WARRANTY
The warranty covers all defects in materials and workmanship. The warranty does not apply if the unit has
been subject to physical abuse, improper installation, modication, or if the housing or serial/type number
labels on units have been removed.
Blinder International manufactures its products using parts and components, which are new or equivalent
to new in accordance with industry standard practices. The enforceability of this warranty is limited to the
original consumer purchaser. It is not transferable to, or enforceable by, any subsequent owner.
In the event of a defect, malfunction or other failure to conform to this warranty, Blinder International will,
at its sole discretion, repair or replace the unit at no charge. The customer is responsible for all shipping
costs in connection with warranty service pursuant to this warranty.
The warranty commences on the date of the retail purchase and shall be eective for the minimum period
set by each country’s laws. This period can be extended to 2 year by registering the product as instructed
below within 30 days from purchasing. There are no express warranties covering the unit other than those
set forth in this warranty. All implied warranties are limited to the period of the warranty and no warranties,
expressed or implied, extend beyond this period.
Blinder International will in no event be liable for any consequential, incidental, indirect or special damages
(including, but not limited to, lost prots) arising out of or in connection with the use, misuse or malfunc-
tion of the unit. Some states do not allow the exclusion of limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you.
WARNING!
Do not look directly into the Blinder M27 / M47 with the naked eye at close range. You won’t see
anything, but you might cause eye damage after prolonged exposure as the Blinder M27 / M47
emits high-power infra red (IR) light, which is not visible to the human eye.
WARNING!
Blinder International does not advocate exceeding the legal speed limits, and shall not be held
responsible for any injuries that could occur due to improper installation or usage of the product.
9
Name
Address
City
Country
E-mail
Retailer / web shop
Date of purchase
Product name
Serial number
(Find the serial number on the CPU)
PRODUCT REGISTRATION
PRODUCT REGISTRATION
Important: This registration entitles you as the owner to 2 years warranty and free software updates
at www.blinder.dk!
PRODUCTREGISTRATION
BLINDER INTERNATIONAL
INDUSTRIVEJ 51 F, TV.
DK4000 ROSKILDE
DENMARK
11
PRODUCTS
BLINDER M27 COINTAINS:
• 2 Transponders
• 1 CPU
• 1 CPU Wiring Kit
• 1 Mounting Kit
BLINDER M47 CONTAINS:
• 4 Transponders
• 1 CPU
• 1 CPU Wiring Kit
• 1 Mounting Kit
WARRANTY SERVICE
To obtain service during the warranty period, please contact your distributor for instructions.
REGISTER YOUR PRODUCT
Register your product and extend your warranty period to 2 years. You can register by sending the registra-
tion card (enclosed in this manual) or register at www.blinder.dk.
BLINDER INTERNATIONAL
Industrivej 51 F
DK-4000 Roskilde
Denmark
Phone +45 3296 3200
Fax +45 3296 3231
E-mail sales@blinder.dk
Web www.blinder.dk
GET THE MOST OUT OF YOUR BLINDER
Stay protected with software updates at www.blinder.dk
This product is covered by U.S. Patent No. 6,833,910,
European Patent No. 1549969 and other patents.
Blinder is registered trademark of Blinder International, Denmark
REGISTER YOUR PRODUCT
Register your product and extend your warranty period to 2 years.
You can register by sending the registration card, (enclosed in this
manual) or register at www.blinder.dk
www.radarwarner.de
+49(0) 641 - 9 72 86 45
This manual suits for next models
1
Table of contents
