BLOCKids Outdoor 6 Instruction Manual

Instructions for installing the BLOCKids children's climbing wall onto
interior walls
(more information at https://youtu.be/ MF2M_9c5Pw )
List of individual components *):
1. BLOCKids Climbing boards, si e 118 * 78 cm
2. BLOCKies Climbing holds manufactured by VirginGrip s.r.o.
3. M10 screws with cylindrical heads for installation of climbing holds, hexagon socket
4. Uni screws ZH Torx 40, 120 * 80 mm
5. Fischer DuoPower dowels 10 * 80 mm
*) The number of individual components varies according to the type of BLOCKids set ordered - see
the packing list enclosed ith the order
Installation of the BLOCKids climbing wall
1. Installation of BLOCKids boards
Install each BLOCKids board in the order shown in the figure below. The order depends on
the number of boards ordered in the BLOCKids set:
Art.Nr. 3165401
3165414
3165427
3165430

 Positioning:
One by one, place the individual boards against the wall at the required height
from the ground (maximum 20 cm above the ground). The lower edge of the
board can also be placed directly on the floor or on the ground. Mark the location
of all 6 holes on each board on the wall. When positioning, use a water level to
make sure that the top edge of the board is level. Also
make sure that the adjacent boards fit together well.
 Drilling holes in the all and placing the do els:
Drill the holes with a minimum depth of 100 mm into the
marked points on the wall. Use a wall drill bit with a
diameter of 10 mm, and always drill perpendicularly to the
wall. Use a hammer to place dowels into the holes drilled
in the wall. The Fischer DuoPower dowel can be installed
in the following wall types:
 Concrete
 Full brick
 Solid sand-lime bricks
 Lightweight concrete
 Vertically perforated bricks
 Perforated sand-lime bricks
 Lightweight concrete hollow core panels
 Hollow brick and concrete ceilings, etc.
 Natural stone
 Solid blocks made of lightweight concrete
More information at https://youtu.be/VydpYspoY8A
 Attaching the boards to the all
Now place the boards against the wall and start installing them in the order
shown above, using Torx 40 countersunk screws. Use a Torx L-key or a TX40 Torx
bit to install the screws.
2. Installation of climbing holds on BLOCKids boards
The climbing holds supplied by VirginGrip come in a variety of si es. We recommend placing
smaller climbing holds in the lower part of the climbing wall as footholds and placing the
other holds randomly at your discretion. Additional climbing holds can be ordered at
www.virgingrip.com.

 Use the supplied M10 socket head cap screws to
install the climbing holds. Each screw should protrude
at least 5 mm on the other side when inserted into
the hole of the climbing hold. Continue to install the
holds using a hex key or an 8 mm hex key bit in the
threaded anchors of the BLOCKids boards. Tighten
each hold carefully so that it does not rotate. The
setting torque for fixing the central screw when using
a torque wrench should be 20-25 Nm.
3. Installation of accessories
 Installation of BLOCKids ladder rungs
Use the supplied M10 countersunk screws to install the ladder rungs. Perform the
installation using a hex key or a 6 mm hex key bit. Install the ladder rungs
hori ontally in the pre-threaded BLOCKids boards.
 Installation of BLOCKids impact mattresses
Place the impact mattresses on the stop with the BLOCKids climbing wall. Place
the mattresses on the floor with the patterned bottom sides rubberi ed with anti-
slip treatment so that the velcros are facing upwards. Securely connect the
individual mattresses with velcro so that the velcro prevents climbers’ limbs from
slipping between the individual mattresses, thus preventing possible injuries.
4. Recommended protective equipment
 Protection glasses
 Thin work gloves
 Safety shoes