Cellink BIO X HD Camera Toolhead User manual

BIO X HD Camera Toolhead
User Manual

Contents
1.Package contents 1
2.Technical specicaons 3
3.Safety informaon 7
3.1 BIO X system warnings 8
3.2 HD Camera Toolhead warnings 8
4.Geng started 9
4.1 Unpacking and installaon 10
5. Inial calibraon, focusing and manual
image capture 13
5.1 Your rst image 14
5.2 Automated imaging during print 19
5.3 Removing the HD Camera Toolhead 21
6.Relevant G-code commands 23
7.Frequently asked quesons 27
8.Maintenance 31
Support informaon 33

1
Package contents
01

2
01 Package contents
Item Part number Quanty
HD Camera Toolhead D16110020853 1
Lens cap D16110020652 1
Observaon pad D16110022041 1

3
Technical specicaons
02

4
02 Technical specicaons
• Resoluon: 1600 x 1200 pixels for captured pictures.
• Maximum eld of view: 37 x 28 mm.
• Minimum eld of view: 7.4 x 5.5 mm.
• Dimensions (height x width x depth): 35.4 x 127.5 x 46.6 mm.
• Connecon: BIO X toolhead mount and mini-USB.
• Weight: 235 g.
• Material composion:
◎External surfaces: Powder-coated steel on front, top, boom and back.
◎Internal surfaces: PA plasc.
• Recommended operang temperature: 20-23 degrees Celsius.

5
02 Technical specicaons
Figure 1: Theorecal maximum movement range shown from the top and side view when using HD Camera Toolhead.
Movement range might be lower when combining the HD Camera Toolhead with a printhead that restricts printbox
movement. Please consult manuals for the specic printheads used to determine potenal restricons.

6

7
Safety informaon
03

8
03 Safety informaon
3.1 BIO X system warnings
• Please consult the BIO X manual for BIO X-specic and general warnings and safety procedures
3.2 HD Camera Toolhead warnings
• Do not submerge the toolhead in liquid or use excessive spraying to clean it. Liquid inside the toolhead risks damaging the circuitry and
motor.
• Do not manually move the mount. Moving the mount manually will damage the motor. If the mount needs to be moved, place the toolhead in
the loading posion described in the Geng Started secon.
• Use the proper method to load and unload the HD Camera Toolhead onto the BIO X mounts. Instrucons are outlined in the Geng Started
secon. While loaded on the BIO X, do not pull or push the toolhead with excessive force, especially when the BIO X system is turned on. This
can damage the motor and its guides.
• Do not use a jerking moon to remove the toolhead. Using a jerking moon risks hing and damaging the HEPA lter.

9
Geng started
04

10
04 Geng started
4.1 Unpacking and installaon
Figure 2: Components of the HD Camera Toolhead.
1. Focusing knob
2. Body
3. Lens cap
• Open the package. Remove the HD Camera Toolhead.
• Remove the lens cap from the HD Camera Toolhead.
•To insert the toolhead, align the toolhead above a mount
(Figure 3A, B) and push downward (Figure 3C, D). Secure the
toolhead mount with your other hand to prevent the motors from
moving during attachment.

11
04 Geng started
Figure 3: Inserng the HD Camera Toolhead into a BIO X mount.
ABC D

12
04 Geng started
Figure 4: Aaching the micro-USB to the BIO
X printbox.
• Make sure the camera light turns on aer the toolhead clicks onto the mount (Figure 3D).
• Connect the mini-USB cord to the mini-USB port on the printbox to enable the camera to
save images (Figure 4).

13
Inial calibraon, focusing and
manual image capture
05

14
05 Inial calibraon, focusing and
manual image capture
5.1 Your rst image
1. Ensure the HD Camera Toolhead is properly installed (Secon 4).
2. Insert a USB ash drive in the BIO X.
3. Go to the Move and Calibrate tab on the right side of the screen and home the system (Figure 5).
Figure 5: Homing the system.

15
05 Inial calibraon, focusing and
manual image capture
4. Wait unl the system has homed. Ensure the HD Camera Toolhead is in the acve posion. You
can place the toolhead in the acve posion using the Tools tab on the Ulies menu (Figure 6).
Figure 6: Pung the toolhead in the acve
posion.

16
05 Inial calibraon, focusing and
manual image capture
5. Place a calibraon target on the printbed. You can use a piece of paper with printed text.
6. Go to the Camera tab on the right side of the screen.
7. Press the movement commands icon on the top-right side of the video feed to display the movement arrows (Figure 7).
Figure 7: (A) Camera display overview on the Ulies menu. (B) Movement commands overlaid with the
camera display.
AB
Camera View HD Camera Movement