Champ Craft Play Sets Childhood Treasure 4250 User manual
Assembly Instructions
#4250 Childhood Treasure
Tools Required for Installaon
Installaon Tips
Parts Idencaon
#1-
#2-
#3-
#4-
#5-
#6-
#7-
#8-
#10-
#11-
#12-
#13-
#14-
#15-
#16-
Parts Idencaon
#17
#18
#19
#20-
#23-
#22-
2¼” Screw - 1½” Screw-
Swing Hanger -
1⅛” Screw-
#24-
1 ” Pan Head Screw-
#21-
#25—
Metal Bracket -
¼” Lock Nut-
Washer-
1½” Bolt -
Parts Idencaon
Identify two part #3’s, measure from the bottom and mark 47¼” and 77” on each
post using a pencil & speed square.
Identify one Part #1, fasten at 47” with 4 - 2” screws. Two per end.
-
Identify one part #2, fasten at the bottom of the posts with 4 - 2” screws (two per
end). Square the post with part #2 as pictured
-
Identify one part #1, fasten at 77” with 4 - 2” screws. Two per end.
-
Make sure to square all the pieces with the speed square.
Repeat steps #1 through #4
This will create a second section exactly like the one pictured above.
Identify one part #6, center on Part #1 boards and fasten with 4 - 1” Screws (two
per end) (You Must pre - drill the part #6s with a 5/32” drill bit)
-
Secon #1
Identify four part #6’s, fasten the first board 2
-
(You must pre - drill all the part #6s with a 5/32” drill bit)
-
Secon #2
Stand up section #1 place part #2 at the bottom securely fasten with 2 - 2”
screws
-
Section #1
Fasten part #13 to opposite bottom side of section #1 with 2 - 2” screws.
-
Part #13 must extend 19” beyond the
outside edge of the post of section #1.
Stand up section #2 and fasten part #13 and part #2 using 2 - 2” screws per
board.
-
Fasten board #1 to section #1 and section #2 with 4 - 2” screws,
as pictured
-
Fasten board #1 to center of section #1 and section #2 with 4 - 2” screws, as
pictured
-
-
Fasten board #1 to the side of section #1 and section #2, 47 “ from the floor with
4 - 2” screws, as pictured.
-
Lay floor boards (two part #12’s and seven part #2’s). Space them evenly as
pictured.
Fasten board #1 to the side of section #1 and section #2, 47” from the bottom of
the posts with 4 - 2” screws, as pictured.
Now fasten each floor board with 6 - 1” screws per board. Pre - drill Part #12’s
with a 5/32” drill bit before fastening.
-
-
-
Fasten one part #1 to section #1 and section #2. Make it even with the top of the
part #1 2x4 as shown. Fasten with 4 - 2” screws per board (two per end).
Repeat step #16 on the opposite side.
Identify part #7 and part #8. Fasten the #8 to the #7 3” down from the end of
part #7 with 3 - 2” screws. The screws will go through #7 and into #8. You will
need a left and a right as pictured.
This creates the Swing
Beam Attachment Block.
Fasten the Swing Beam Attachment Block, that was assembled in step 17, to the
center of the part #1 2x4s as pictured with 4 - 2” screws per board.
-
Part #13
Fasten four part #5’s (two on each side of the Attachment Block). Space them as
pictured below starting in the center. Fasten them with 4 - 1” screws per board.
Pre - drill with 5/32” drill bit before fastening.
-
Table of contents
Popular Play Set & Playground Equipment manuals by other brands
SportsPlay
SportsPlay JR GEO-DOME quick start guide
HONEY JOY
HONEY JOY NP10765 user manual
Step 2
Step 2 Hot Wheels Extreme Thrill Coaster manual
Swing King
Swing King Irma Small 7850050 Assembly instructions
Step 2
Step 2 Extreme Roller Coaster manual
Step 2
Step 2 Climber & Slide Pirate's Paradise 4925 manual
MD SPORTS
MD SPORTS AH084Y19030 Assembly instructions
Step 2
Step 2 Playhouse Climber 7543 manual
NI Climbing Frames
NI Climbing Frames Karlas Kingdom instruction manual
Step 2
Step 2 ADVENTURE CAMPER 4205 Assembly instructions
Step 2
Step 2 My Clubhouse Assembly
Playnation
Playnation Riviera Playhouse 1536 manual