CHIEF PSMH2482 User manual

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Large Flat Panel Static Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PSMH2482

PSMH2482 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support a minimum of 2,000lbs (907.185kg). Reinforce
the structure as required before installing the component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the PSMH-2482 mount does not
exceed 300 lbs (136.08 kg).
DIMENSIONS
1.89
47.9
35.27
895.8
29.50
749.3
62.00
1574.8
55.12
1400
31.50
800
4.00
OFFSET FROM WALL
101.5

Installation Instructions PSMH2482
3
LEGEND
TOOLS FOR INSTALLATION/PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Hex-Head Wrench
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
C(2)
G(4)
5/16-18 x 5/8" M8 x 45mm
F(18)
5/16-18"
E(4)
M8
A(2) B(2)
1/4" 9/16" M5 (included)
D(4)
[Vertical Bracket] [Horizontal Bracket]
[Locking Flag] H(8)
3/8" J(2) 5/16" K(1)
M5 L(1) 3/16"
3/16"(included)

PSMH2482 Installation Instructions
4
ASSEMBLY AND INSTALLATION
Mount Assembly
1. Attach locking flags (G) to vertical brackets (A) by installing
two 5/16-18 x 5/8" button head cap screws though lower
hole on locking flags, upper hole on vertical brackets, 5/16"
washers (J) and into two 5/16-18" lug nuts (F). (See Figure
1)
Figure 1
2. Attach two vertical brackets (A) to two horizontal brackets
(B) using remaining sixteen 5/16-18 nylon lock nuts (F).
(See Figure 2)
Figure 2
Mount Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! The mount weighs
in excess of 75 lbs (34.02 kg). ALWAYS use appropriate
lifting device and follow all safety practices when moving and
installing this mount.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s
responsibility to make sure the structure to which this mount
is being attached can support a minimum of 2,000 lbs
(907.18kg). Reinforce the structure as required before
installing this mount.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the PSMH-2482 mount does not
exceed 300 lbs (136.08 kg).
1. Using appropriate lifting device, raise assembled mount
and place mount against wall in desired installation
location. (See Figure 3)
2. Level and adjust horizontal position making certain slots in
upper and lower horizontal brackets on mount are properly
positioned over studs.
3. Using a pencil, or similar marking tool, mark the location of
mounting holes in base onto surface. (See Figure 3)
4. Drill eight 1/4" pilot holes at marked locations. (See Figure
3)
(A) x 2
(G) x 2
(C) x 2
(J) x 2
(F) x 2
1
2
(F) x 16
(B)
(A)
(A)

Installation Instructions PSMH2482
5
Figure 3
3
1
2
4
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT overtighten
hardware!
5. Secure mount to studs using appropriate hardware for
mountingsurfaceandeight3/8" washers(H). (SeeFigure 4)
Figure 4
Display Installation
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware.
1. Move locking flags (G) on mount to the OPEN position. (See
Figure 5)
Figure 5
5
(H) x 8
OPEN
1
(G) X 2

PSMH2482 Installation Instructions
6
Figure 6
(E) x 4
(D) x 4
2
2. Install four mounting buttons (E) onto display using four M8
x 45 button head cap screws (D). (See Figure 6)
3. Lift display following lifting instructions provided by display
manufacturer.
4. Align mounting buttons on display with teardrop mounting
holes in mount. (See Figure 7)
Figure 7
5. Move display forward until recessed area of mounting
buttons is positioned over lower area of teardrop mounting
holes. (See Figure 7)
6. Lower display until recess area of mounting buttons is
seated in lower area of teardrop mounting holes. (See
Figure 7)
7. Move locking flags (G) to CLOSED position and lock if
desired. (See Figure 8)
Figure 8
8. Route wires and cables to display.
4
3
6
padlock here
CLOSE
(G) X 2

Installation Instructions PSMH2482
7

PSMH2482 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8831-002000 Rev00
©2009 Milestone Technologies, a
Duchossois Group Company
www.chiefmfg.com
03/09
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P+86-755-8996 9226
F+86-755-8996 9217