Comtrol ROCKETLINX ES7206-XT User manual

QUICK INSTALLATION GUIDE
2000584 Rev E | Release Date- March 2014
ROCKETLINX ES7206-XT
Industrial PoE Plus Switch

INTRODUCTION
The RocketLinx ES7206-XT is an industrial 6-port Gigabit 802.3af/at PoE
Voltage Boost Switch.
SeetheComtrolwebsiteforproductspecicaons.
INSTALLATION OVERVIEW
YoucanusethefollowinginformaontoinstalltheES7206-XT.TheES7206-XT
istobeconnectedtoPoEnetworkswithoutroungtooutsidetheplant.
Wiring the Power Inputs
TheES7206-XTprovidesredundantpower,reversepolarityprotecon,over-
currentproteconandacceptsaposiveornegavepowersourcebutPWR1
andPWR2mustbeappliedwithpowersourcesofthesamepolarity.
Theterminalblockaccepts12-24AWGwire.UseaULlistedpowersupply
withtherequiredoutputvoltageof12-36VDCtodeliverIEEE802.3atPoEPlus
onallPoEports(Ports1-4).Thepowersupplymustberatedasfollows:
• 802.3af-96Was(Minimum)
• 802.3at-168Was(Minimum)
1
Power Supply AC Power Input
12-36VDC/7A
(UL Listed)
V+
V-
Wiring Posive Power Supplies
Power Supply AC Power Input
12-24AWG
12-24AWG
V+
V-
DC Power Input
12-36VDC
12-36VDC
DC Power Input 12-36VDC/7A
(UL Listed)
Relay
PWR1PWR2
+
-+
-

Powershouldbedisconnectedfromthepowersupplybeforeconnecngitto
the switch. Otherwise, your screwdriver blade can inadvertently short your
terminalconneconstothegroundedenclosure.
1. InserttheposiveandnegavewiresintoPWR+andPWR-contacts
(PWR1andPWR2).Youcanconnectasinglepowersupplyortwopower
supplies depending on your requirements.
Ifbothpowerinputsareconnected,theES7206-XTwillbepowered
fromthehighestconnectedvoltage.Theunitcanbeconguredto
signalanalarmforlossofpowerineitherPWR1orPWR2.
2. Tighten the wire-clamp screws to prevent the wires from being
loosened.
Note: When the ES7206-XT is in operaon, cauon must be taken to not touch the hot
surface of the product enclosure.
Electrical Specicaons Value
PowerInput 12-36VDC
PowerConsumpon
(withoutPDloading) • 840mA@12VDC • 420mA@24VDC
• 280mA@36VDC
PowerConsumpon
(withPDloading) • IEEE802.3af:6.25@12VDC
• IEEE802.3af:4A@24VDC
• IEEE802.3at:7A@24VDC
• IEEE802.3af:2.67A@36VDC
• IEEE802.3at:4.67A@36VDC
MaximumOutput/PowerPoEPort • 15W(IEEE802.3af)
• 30W(IEEE802.3at)
(table connued on next page)
2

3
Electrical Specicaons Value
Total PoE Power
Budget VIN=12VDC • 60W@-40°to70°C • 55W@70°to75°C
VIN=24VDC • 110W@-40°to65°C
• 100W@65°to75°C
VIN=36VDC • 110W@-40°to65°C
• 100W@65°to75°C
Operang Temperature -40°to75°C
Storage Temperature -40°to85°C
Note: Exceeding the recommended power and operang temperatures may
result in failures or damage.
Wiring the Alarm Relay Output
Thealarmrelayoutputordigitaloutput(DO)contactsareontheterminal
block connector. The alarm relay output contacts are normally open. The
alarmrelayoutputcontactsclosewhenthealarmisenabledwiththeDIP
switches and there is a port link failure or PoE failure on a port.
Therelaycontactsupportsupto0.5Aat24VDC.Donotapplyvoltageand
currenthigherthanthespecicaons.
Thealarmrelayoutputiscontrolledbythepre-denedrules.Toacvatethe
alarmrelayoutputfuncon,refertothefollowingdrawing.
Earth Ground
+
Alarm Relay Output
DIP Switch
Alarm Control
Alarm
Relay
PWR2 PWR1
Power
Source
Buzzer/
PLC
Input
12 - 24
AWG Wire
24VDC/0.5A (Max)

Seng the DIP Switch
TheES7206-XThasan8-pinDIPswitchlocatedontheboompanelto
congurethePortLinkAlarmfortheEthernetports.Thefollowingtable
showstheDIPswitchnumbermappingtothecorrespondingopons.
Port
1
Port
2
Port
3
Port
4
Port
5
Port
6
PWR
Alm
SFP
100
DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8
ThistableshowstherelaonshipbetweentheDIPswitchnumber,posion,
andfuncon.
Switch Posion Funcon
1-6 ON Enables port failure alarm for corresponding port
OFF(Default) Disablesportfailurealarmforcorrespondingport
7ON Enables power event alarm
OFF(Default) Disablespowereventalarm
8ON EnablesSFPportfor100BASE-FX
OFF(Default) Supports Gigabit SFP in SFP port
Note: Aer connecng the SFP or changing the speed through DIP 8, cycle the
power to acvate the SFP.
Grounding the ES7206-XT
Wiretheearthgroundtoensurethesystemisnotdamagedbynoiseorany
electricalshock,werecommendthatyoumakeadirectconneconbetween
the ES7206-XT and earth ground.
Usingascrewdriver,loosentheearthgroundscrewontheboomof
theES7206-XTandthenghtenthescrewaertheearthgroundwireis
connected.
4

5
Mounng the ES7206-XT
TheDINrailclipisaachedtotheES7206-XT.
1. InserttheupperendofDINrailclipintothebackofDINrailtrackfrom
its upper side.
2. LightlypushtheboomofDINrailclipintothetrack.
3. VerifythattheDINrailclipisghtlyaachedonthetrack.
Note: When the ES7206-XT is in operaon, cauon must be taken to not
touch the hot surface of the product enclosure.
Connecng the RJ45 Ethernet Ports
Connect one end of an Ethernet cable into the Ethernet port of the
ES7206-XTandtheotherendtotheaachednetworkingdevice:
• Ports1-4areGigabitPoEportsthatsupportIEEE802.3af/802.3at(PoE+)
• Port5isaGigabit(10/100/1000BASE-TX)port
• Port6isaGigabitSFPport,whichisdiscussedinthenextsecon
TheportssupportGigabithalf/full-duplex.AllRJ45portsauto-detectthe
signalfromconnecteddevicestonegoatethelinkspeedandduplexmode.
AutoMDI/MDIXallowsuserstoconnectanotherswitch,hub,orworkstaon
without changing straight-through or crossover cables.
Link/ActLEDsarelittoindicatetracandlinkstatus,seetheLEDssubsecon
formoreinformaon.
1000BASE-TX

Alwaysmakesurethatthecablesbetweentheswitchesandaacheddevices
(forexample,switch,hub,orworkstaon)arelessthan100meters(328
feet).YoushoulduseCategory5cableorhigher.
Connecng the SFP Port
You can connect an SFP transceiver to Port 6. Comtrol recommends using
Comtrol-approved SFP transceivers. Cross-connect the transmit channel at
each end to the receive channel at the opposite end as illustrated in the
gure.
MakesurethatyouuseanSFPbertransceivercompliantwithUL
cercaonandEN60825Class1.
LED INDICATORS
LED Status Descripon
PWR1/2 Green The terminal block is receiving power
O The terminal block is not receiving power
(table connued on next page)
6
A B
TX
RX
TX
RX

LED Status Descripon
Alm Red Oneofthefollowinghasoccurred:
• Port link failure has occurred
• PowerhasbeenremovedfromPWR1orPWR2
• Port6SFPis100BASE-FXandhaslost
connecon/link
O Nofailurehasbeenfound
PoE 1-4 Yellow TheportisprovidingPoEpowertothePD
O NoPDisaached
P 1-5
LNK/ACT
Green Anetworkdeviceisaached
Blinks ThereisavalidEthernettransmit/receiveacvity
to/from the connected network device
O Theportlinkisnotacve
P6
LNK
Green Anetworkdeviceisaached
Blinks ThereisavalidEthernettransmit/receiveacvity
to/from the connected network device.
O Theportlinkisnotacve
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method Web Address or Phone Number
Support hp://www.comtrol.com/support
Downloads p://p.comtrol.com/html/default.htm
Website hp://www.comtrol.com
Phone +1763.957.6000
7