Cool Fin LED Hybrid Series User manual

Cool Fin LED Hybrid series LED Street /Roadway /Area Light-347 V
Main specifications:
Model No.
Nominal
Wattage
Dimensions (L x W x H) Weight
EPA*
Working
Environment
IP
CFSLPMHBC80 80w 523 mm ( 20.6" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 7.1 kg ( 15.6
lbs.
) 0.5
-40℃―+50℃IP67
CFSLPMHBC120 120w 583 mm ( 22.9" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 8.2 kg ( 18.1
lbs.
) 0.54
-40℃―+50℃IP67
CFSLPMHBC160 160w 643 mm ( 25.3" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 8.9 kg ( 19.5
lbs.
) 0.59
-40℃―+50℃IP67
CFSLPMHBC200 200w 703 mm ( 27.7" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 10 kg ( 22.1
lbs.
) 0.63
-40℃―+50℃IP67
CFSLPMHBC240 240w 763 mm ( 30.1" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 11 kg ( 23.8
lbs.
) 0.67
-40℃―+50℃IP67
CFSLPMHBC280 280w 823 mm ( 32.4" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 11 kg ( 25.2
lbs.
) 0.72
-40℃―+50℃IP67
CFSLPMHBC320 320w 883 mm ( 34.8" ) x 345 mm ( 13.6" ) x 116 mm ( 4.6" ) 12 kg ( 27.5
lbs.
) 0.76
-40℃―+50℃IP67
Input Voltage: 347 to 480V~ 50/60Hz
IMPORTANT INSTALLATION INFORMATION
347 V - Cool Fin LED Hybrid series LED Street /Roadway /Area Light
INSTALLATION INSTRUCTION
• Ensure there is adequate free air circulation of at least 50cm around the luminaire. All luminaires run hot. It is the installer's responsibility to consider fire
risk and take appropriate precautions.
• The luminaire must not, under any circumstances, be installed directly to flammable materials, and luminaires must not be covered with any flammable
materials.
The ingress protection of the fixture is IP67 if the mains supply cable's specification is H07RN-F 3*1.5m㎡.
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
LEAVE A COPY FOR THE USER / MAINTENANCE ENGINEER FOR FUTURE REFERENCE
• Before commencing installation or maintenance, ensure electricity is switched off at the mains. Installation or maintenance should be carried out by a
qualified electrician.
Drawings herein for
CFSLPMHBC 200 w are used as
examples for all the below
listed models
STEP 1: Loosen nuts from pole locking bolts, then slide fixture
on to pole through opening (tenon) on the rear of housing. See
Figure 1.
STEP 2: Ensure to slide fixture to the inner end of tenon, then
tighten locking bolts with 5mm hex wrench or its equivalent to
ensure the fixture is fixed to pole firmly. See Figure 1.
CFSLPMHBC200
The installation instruction is subject to change without prior notice.
For more about the product info, please visit www.arrlux.com or consult factory.
Page 1 of 2

STEP 3: Loosen hinged hatch locking bolts with 5mm hex
wrench or its equivalent, and open the hatch for led driver
compartment access. See Figure 2.
STEP 4: Get mains power supply cord into led driver
compartment via cable gland, and use open spanner or similar
tool to lock the gland to mains power supply cord tightly. See
Figure 3.
STEP 5: To adjust tilting angles from front to back, firstly
loosen the screws on both sides of the rotatable tenon using
6mm hex wrench or its equivalent, see Figure 4. Secondly
locate the tilt and fix it by tightening the mentioned screws at
45 N.m.torque. To adjust the fixture from side to side, loosen
the pole locking bolts, see Figure 1, when ready, tighten the
pole locking bolts at 45 N.m, then tighten the pole locking nuts
at 10 N.m torque so as to ensure the lighting fixture is installed
to the pole firmly.
IMPORTANT - DO NOT exceed the torque level on the mount
bolts. Exceeding recommended torque value resulting in
excessive deformation of pole mounting bracket will cause
stripping of mount hardware which could lead to an unsafe
mounting condition.
STEP 6: Reference “Electrical Connections” section for
completing electrical connections. See Figure 6.
PHOTOELECTRIC CONTROLLER INSTALLATION (OPTIONAL)
STEP A: Make sure a NEMA receptacle on top of fixture is
available.
STEP B: Find out the size difference of three pins on P.E.C.U., the
size difference of three slots on NEMA receptacle.
STEP C: Insert P.E.C.U. in receptacle, and twist it clockwise firmly.
STEP D: Firmly rotate photo-control with its photo-eye
approximately in the ‘N’ north direction.Some photo-controls
operate best somewhere between NW and NE. See Figure 5.
WIRING INSTRUCTION
STEP I: Connect the LINE wire in the mains power supply cord to
the L marked hole In the terminal block from the external
junction box, and tighten the connection properly.
STEP II: Connect the NEUTRAL wire in the mains power supply
cord to the N marked hole in the terminal block from the
external junction box, and tighten the connection properly.
STEP III: Connect the YELLOW/GREEN GROUNDING wire in the
mains power supply cord to the G marked hole in the terminal
block from the external junction box, and tighten the connection
The installation instruction is subject to change without prior notice.
For more about the product info, please visit www.arrlux.com or consult factory.
Page 2 of 2