COOLZY COOLZY-PRO PC9RL Operating and maintenance manual

COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1 1
USER GUIDE AND WARRANTY
This product contains a small amount of
R290 refrigerant with negligible global
warming impact. The refrigerant is amma-
ble. Read the safety precauons rst!
Avoid using this product in a wet environ-
ment. Ensure that anyone using this prod-
uct is aware of normal safety precauons
for household electric appliances. Caution
Risk of re
Coolzy products are distributed in the European Union and UK by Close Comfort Internaonal
Pte Ltd, Singapore, UEN 201527973E.

2 COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1
PARTS

COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1 3
Microclimate temperature
setting
The temperature of the cool air at the
outlet is dependent on the environment
temperature and humidity, usually 8 to
14 degrees less than the ambient tem-
perature. The thermostat turns o the
compressor if the temperature of the air
returning to the air condioner is below
the set temperature. Press ▲to increase
or ▼to reduce the set temperature.
SLEEP
1) Press “SLEEP” to set sleep funcon.
The fan changes to low speed for sleep-
ing. Press again to cancel sleep funcon.
2) The temperature seng will increase
by 0.5 °C aer half an hour and 2 °C aer
2 hours.
3) When you turn o the unit, the sleep
funcon will be cancelled automacally.
TIMER
The mer is used to turn o the unit au-
tomacally aer the seng me is over.
1) Press the “TIMER” key to set the num-
ber of hours of desired operang me.
2) Once the set me has come to an end,
the unit will turn o automacally.
3) Press the “POWER” key to turn o the
machine and cancel the mer.
AUTO
The fan speed changes automacally.
When the ambient temperature is 2 or
more degrees higher than the set room
temperature, the machine will run with
high fan speed. It will automacally
switch to medium and low fan speed
when the ambient temperature gets
closer to the set temperature.
Cooling
Fan
Sleeping
Timer ON/OFF
Temperature
Automatic air
flow speed
High speed
Medium speed
Low speed
AUTO
HI
MED
LO
C
AUTO
FUNC SLEEP
TIMER
AUTO
HIGH
LOW
MED
POWER








REMOTE

4 COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1
GETTING STARTED
1) Aer removing Coolzy from the box, place it in
an upright posion.
2) Remove the cable from the drawer at the back
of the unit and insert the plug into a wall outlet.
Make sure you push the drawer fully back in so it
aligns with the back panel.
3) Open the warm air deector fully. This will
turn on the unit and the compressor will start.
4) Open the cold air deector and allow 2 min-
utes for the air coming out to feel cold. Use the
remote control to adjust fan speed. Keep the
temperature seng at 17 °C unless the air ow
feels too cold.
5) Keep a door or window open so fresh air circu-
lates unless it is extremely hot or windy outside.
6) Avoid using a fan nearby as it can disrupt
Coolzy’s gentle air ow.
7) The adjustable nozzle (“focus enhancer”)
extends the range of cooling and, aer ng the
separate transparent deector
ap, enables a higher angle of air
ow.
Posion Coolzy close enough
for comfort. The ideal range of
distance is 1.5 - 3 metres. Arrange
the angle of the cold air deector
so cool air ows around face and
shoulders.
For sleeping, arrange your unit
about 15cm from the end of the
Drape a curtain as shown to exclude
light when sleeping. Make sure that
the room air intake is at least 15 cm
from the wall!
For a small room, place the unit near
an open window or doorway.
IMPORTANT
Always keep Coolzy upright. It may have been
stored or transported on it’s side or laid at by
mistake, so please stand it upright for at least 12
hours before plugging it into power and turning it
on. Failing to do so may damage the unit.

COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1 5
bed. Adjust the cold air deector and
adjustable nozzle to the desired angle
so the cool air ows over your face
and upper body. It also works with
larger beds for two people.
Use the oponal Igloo tent for a more
intense cooling eect and insect
protecon. We recommend using
the Igloo tent for sleeping if indoor
temperature is over 27 °C.
DEHUMIDIFICATION
Coolzy condenses water from the room air in humid weather condions. Normally
this water evaporates into the air emerging from the warm air outlet, improving the
cooling power.
To collect the condensed water instead, open the cable drawer and remove the
stopper just above it. This will allow some of the condensed water to collect in the
drawer. When the cable drawer is full, the white water drop indicator comes on and
Coolzy will pause. Carefully remove the cable drawer and empty the water. The cable
drawer can store about two litres of condensed water.
Remember to replace the stopper for normal, high eciency cooling.

6 COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1
ADJUSTABLE NOZZLE
Coolzy has an adjustable nozzle that adjusts the cool air throw (Focus Enhancer).
Push the blue nozzle down for a more focused air ow that cools at a greater dis-
tance. Li the nozzle for a gentler ow.
Make sure the nozzle is pushed down before closing the cool air deector.
For a higher angle of air ow, aach the transparent ap to the end of the cool air
deector. Make sure the straight edge is facing you and the two notches slide under
the cool air deector.
To remove, simply pull the ap o.
Tips
• Adjust the angle of the cool air deector to ensure that cool air ows past face
and neck. Adjust nozzle to about 45° for best cooling eect.
• Turn o fans when using Coolzy. Dras from nearby windows and fans may dis-
rupt the air jet.
• Pull the nozzle upright for use with the bed tent. If the nozzle is in the down posi-
on, the cool air at the boom of the tent will mix with the warm air at the top.
• In humid weather, it is normal for moisture to condense on parts of the nozzle.

COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1 7
USER MAINTENANCE
We recommend inspecng at least the return air inlet lter once every two weeks.
Once there is a noceable amount of dust, clean all three lters by rinsing them
under running water.
Remove the adjustable nozzle to access the foam lter beneath it. Replace the nozzle
aer cleaning the foam lter.
In dusty locaons, consider arranging for an air condioning technician to clean the
inside before the summer season.
The refrigerant circuit is permanently welded: there is no need to recharge the gas.
INDICATOR LIGHTS
Power (green light)
This shows that the electrical power is on. When the green light ashes, Coolzy is
waing 1 – 2 minutes for the compressor to start cooling.
Water drop (white light)
In normal condions, all the water condensed inside the cooler will evaporate into
the air emerging from the warm air outlet. This evaporaon increases the cooling
performance in humid condions.
If you remove the stopper, following the dehumidicaon instrucons, condensed
water ows into the cable drawer instead. The water drop light comes on when the
cable drawer is full of water.
The water drop light also comes on if the cable drawer is not fully inserted and ush
with the back panel.
When it is extremely humid, greater than 95% lasng for several hours, water can
overow from the cooler into the cable drawer.
If the water drop light is on, carefully remove the cable drawer and empty any water.
Make sure you push the drawer fully back in so it aligns with the back panel.

8 COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1
Snowflake (blue light)
The cooler temperature so low that there is a risk that ice may form, damaging the
tubes in Coolzy. Some combinaons of low temperature, humidity and atmospheric
pressure can lead to frosng. Allow the fan to operate for a few minutes to warm up
Coolzy.
Also, check the air inlet lters for excessive dust build-up. Ensure that there is nothing
blocking the either of the air inlets such as a curtain, cushion or bedding.
Thermometer (red light)
The compressor has overheated. Coolzy can be used in ambient temperatures up to
40 °C. Above that temperature, the compressor may overheat. Wait for 10 – 20 min-
utes and try again. Avoid using Coolzy in direct sunlight.
Check the air inlet lters for excessive dust build-up. Ensure that there is nothing
blocking the either of the air inlets such as a curtain, cushion or bedding.
TROUBLESHOOTING
Symptom 1 – Green light is not on when trying to turn on
Coolzy
Make sure the warm air deector is fully open. Check to see if the power supply is
properly connected and on. If the power cord seems properly connected, try a dier-
ent power supply. Make sure you push the cable drawer fully back in so it aligns with
the back panel.
Symptom 2 – Green light is on with no cooling
The green light ashes, the fan runs and the compressor waits to start cooling for
about 90 seconds. This delay protects the compressor from damage.
If the green light is on and the fan is running, and there is no apparent cooling aer 2
minutes, check that Coolzy is in cooling mode. Press the ‘FUNC’ buon on the remote
unl the snowake icon appears to acvate cooling mode. Reduce the temperature
seng because the thermostat may be prevenng the compressor from starng.
Symptom 3 – Water sloshing noise
In extremely high humidity, the producon of condensed water may exceed the ca-
pacity to evaporate water at the condenser heat exchanger. As more water accumu-
lates than in normal condions, there may be a percepble sound of water cascading
o the condenser at the back of the machine. This is normal behaviour. If the sound
is annoying, consider removing the rubber bung temporarily. The water will drain into
the cable drawer. However the machine will stop cooling when the cable drawer is
full of water.
Symptom 4 – Room seems to warm up
As you become accustomed to the cool microclimate that Coolzy provides for you,
the other parts of the room may seem to be warmer. There may be a slight increase
in air temperature in the space above the warm air deector, but this is normally not
enough to heat up the lower part of the room.
Keep a door or window open. This is a healthy opon. Posion Coolzy’s warm air
outlet to face the open window or door so warm air can ow out more easily. Unlike
normal room air condioners, Coolzy works just best with open doors or windows

COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1 9
and fresh air circulang.
A slight temperature increase can occur in a small room, especially if the windows are
closed. The setup instrucons show how to minimize this eect. Visit www.coolzy.
com for more suggesons to improve venlaon.
Symptom 5 – Gradual loss of cooling
Dust accumulang on the air lters will reduce the cooling. Clean all three air lters
following the instrucons in this guide.
SUPPORT
www.coolzy.com provides FAQs and helpful informaon, updated frequently, along
with your local retailer and service agent informaon and your local customer sup-
port phone number.
Ask any general, support, warranty or technical quesons by emailing us at
[e-mail].

10 COOLZY-PRO Model PC9RL User Guide EN2022 Rev1.1
SPECIFICATIONS
COOLZY
Model number PC9RL
Power source 220 - 240 V AC, 50 Hz
Minimum operang voltage 185 V
Rated power input 430 W (40 °C, 35% RH)
Typical power input 340 W (33 °C, 80% RH)
Compressor type Rotary
Cooling capacity * 800 W - 1100 W (3300 - 4500 BTU/hr)
Cool air ow rate 80 - 115 m3/hr variable
Cool side temperature reducon 8 - 16 °C
Refrigerant R290, 109 g
Power cord, storage drawer † 4 m, 2.5 litres
Operang environment (indoors) 20 °C - 40 °C
Width 273 mm (packed 310)
Depth 385 mm (packed 410)
Height 550 mm (packed 610)
Weight 15.4 kg (packed 17 kg)
Noise ‡ 46 - 54 dBA
Wheels 4 caster wheels
Remote control infrared - temperature, fan speed adjust
Plumbing and pipes needed None
Consumables needed None
Filter cleaning Check every 2 weeks
* Cooling power ranges up to 1100 Wa with automac evaporaon of condensed
water, depending on local temperature and humidity. Electricity consumpon varies
depending on temperature and humidity.
† Drawer can oponally be used to collect condensed water.
‡ Apparent noise level in bedroom, depends on fan speed and furnishings.
Fuse parameters of the machine
Type: 5ET or SMT Voltage: 250V Current: 3.15 A