Cooper Menvier Scantronic 9651 Installation guide

INSTALLATION AND
PROGRAMMING GUIDE
9651
HARDWIRED CONTROL
PANEL

9651 Hardwired Control Panel Installation and Programming Guide
© Cooper Security Ltd. 2004
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security
Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book
are subject to change without notice.
Printed and published in the U.K.
Part number 496929 Issue 2

496929 Page 1
Contents
1. INTRODUCTION..........................................................................................3
Operator Controls and Displays - 9930..........................................................................................................4
System Features.............................................................................................................................................5
Detectors......................................................................................................................................................5
User Control .................................................................................................................................................5
2. Technical Description................................................................................6
Specification ...................................................................................................................................................6
Power Supply ...............................................................................................................................................6
Outputs.........................................................................................................................................................6
Inputs............................................................................................................................................................6
Fuses............................................................................................................................................................6
Control Unit PCB ............................................................................................................................................7
3. INSTALLATION...........................................................................................8
Overview.........................................................................................................................................................8
Cabling Keypads ............................................................................................................................................8
Fitting the System...........................................................................................................................................9
Fitting the Control unit Case.........................................................................................................................9
Fitting a 9930 Keypad ..................................................................................................................................9
Wiring the Control Unit .................................................................................................................................11
Cable Entries..............................................................................................................................................11
Mains Connection.......................................................................................................................................11
Remote Keypads........................................................................................................................................12
Connecting Keypads, ExitTerminate Buttons, LockSwitches and Sounders..............................................................12
Detector Circuit Connections......................................................................................................................13
Using Programmable Outputs....................................................................................................................14
Wiring Keyswitches ....................................................................................................................................15
Fitting a Plug-by Communicator.................................................................................................................16
Fitting a Battery ............................................................................................................................................18
Initial Start Up...............................................................................................................................................18
4. Programming............................................................................................20
Entering Programming Mode........................................................................................................................20
Programming Commands.............................................................................................................................20
Leaving Programming Mode......................................................................................................................24
Engineer Reset...........................................................................................................................................24
Re-entering Programming Mode................................................................................................................25
Restoring the Access Codes (1st stage reset)...........................................................................................25
Restoring All Factory Default Programming...............................................................................................25
Programming Command Reference.............................................................................................................26
0: Country Defaults.....................................................................................................................................26
01 - 08 : Zone Programming ......................................................................................................................26
20: Change Engineer Code........................................................................................................................30
21: Zone Configuration...............................................................................................................................31
22: Loudspeaker Chime.............................................................................................................................31
23: RedCare Reset.....................................................................................................................................31
25: Continuous Sounder.............................................................................................................................31
27: Exit Fault External Sounders................................................................................................................31
28: Status Display.......................................................................................................................................32
29: Entry Alarm Delay Time .......................................................................................................................32
30: Silent or Audible PA .............................................................................................................................32
31: Zone Tamper Reset .............................................................................................................................32
33: System Reset.......................................................................................................................................33
34: PA Reset ..............................................................................................................................................33
35: First Circuit Response..........................................................................................................................33
36: Alarm Abort...........................................................................................................................................33
37: Daytime Tamper Communication.........................................................................................................33
38: System Tamper Reset..........................................................................................................................34

Contents
Page 2 496929
39: Level A Exit Mode.................................................................................................................................34
40: System Auto Re-Arm............................................................................................................................35
41: Bell Delay .............................................................................................................................................35
42: Bell Duration.........................................................................................................................................35
43: Level A Entry Time...............................................................................................................................35
44: Level A Exit Time..................................................................................................................................35
45: Entry/Exit Tone Volume........................................................................................................................35
46: Tamper Alarm Annunciation.................................................................................................................36
50: CSID Code ...........................................................................................................................................36
51: Setting Time and Date..........................................................................................................................36
52: Omit Tamper Allowed...........................................................................................................................37
53: Abort Reset...........................................................................................................................................37
59: Sounder Tamper.................................................................................... Error! Bookmark not defined.
60: Level B Final Exit Operation.................................................................................................................37
61: Level B Entry Route Response............................................................................................................37
62: Level B Exit Mode.................................................................................................................................38
63: Level B Alarm Response......................................................................................................................38
64: Level B Entry Time...............................................................................................................................38
65: Level B Exit Time..................................................................................................................................38
70: Level C Final Exit Operation.................................................................................................................38
71: Level C Entry Route Operation ............................................................................................................39
72: Level C Exit Mode ................................................................................................................................39
73: Level C Alarm Response......................................................................................................................39
74: Level C Entry Time...............................................................................................................................39
75: Level C Exit Time .................................................................................................................................39
76: Level D Exit Mode ................................................................................................................................39
77: Level D Alarm Response......................................................................................................................40
78: Level D Entry Time...............................................................................................................................40
79: Level D Exit Time .................................................................................................................................40
81, 82, 83, : Output Programming..............................................................................................................40
85: Burglar Communications Re-arm.........................................................................................................42
86: Dual Ply Entry Warning ........................................................................................................................43
87: Keypad Dual Key Alarms .....................................................................................................................43
90 - 97: See “5.Testing”..............................................................................................................................44
98: Load Full Defaults.................................................................................................................................44
99: Leave Programming Mode...................................................................................................................44
126: Select Language.................................................................................................................................45
151 - 158: Plug by Communicator Outputs................................................................................................45
5. Testing.......................................................................................................48
Reading the Log (Command 90)..................................................................................................................48
Keypad and Event Log Displays ................................................................................................................48
Testing Outputs (Commands 91-96)............................................................................................................50
Engineer Walk Test (Command 97).............................................................................................................50
Index..............................................................................................................51

496929 Page 3
1. INTRODUCTION
The 9651 control unit is designed to be fully programmable to suit individual
site requirements and user needs. Note that in the UK the product does not
comply with the ACPO 2000 alarm policy and DD243: 2002.
The system comprises a control unit in a metal shielded case and up to four
separate keypads (see Figure 1 on the next page). You should always fit at
least one keypad.
The control unit provides:
° A four-wire bus connection for keypads.
° Connections for eight Fully Supervised Loop (FSL) zones or eight Closed
Circuit Loop (CCL) with a common tamper.
° Connections for three fully programmable outputs.
° Internal sounder loudspeaker output with electronically generated Chime,
Alarm, Fire and Entry/Exit tones. (The volume of the Entry/Exit and Chime
tones can be adjusted).
° Pins and wired harness for a plug-by communication device.
The control unit provides connectors for eight Closed Circuit (CC) zones or
eight Fully Supervised Loop (FSL) zones on its own printed circuit board.
The control unit supports the 9930 sixteen character Liquid Crystal Display
(LCD) keypad. The keypad(s) can accommodate the 934EUR-00 “Prox”
reader module to allow the end users to set and unset the system using a
“Prox” token in place of a four digit access code.
As an Installer you can program the system from the keypads. When
programming from the keypads the programming interface is arranged as a
set of three-digit numbered commands similar to those used by the 9800
family of products.
The system can provide for up to 16 separate users. User facilities include:
° Four different security levels (full and three part sets) on the 9651. The
levels can be programmed by the Installer.
° User programmable Duress code.
° Keyswitch setting/unsetting.
° Dual key PA alarm from the keypads.
Setting, unsetting & resetting using a “Prox” token
Before attempting to program the system, make sure you are completely
familiar with the functions of the system and its programmable options.

3. Introduction
Page 4 496929
1 - Control unit 4 - Door contacts
2 - Keypads 5 - fused mains spur
3 - PIRs
Figure 1. 9651 System Layout
Operator Controls and Displays - 9930
Figure 2. 9930 Remote Keypad.
The 9930 keypad has a 32 character LCD display that shows "first to alarm"
information, level status, and programming commands. In addition there are
three LEDs with the following functions:

3. Introduction
496929 Page 5
aGlows steadily when mains power is present. Flashes when the
system is working from battery backup.
fGlows steadily if a telephone line fault is present.
sGlows steadily if:
a) A fault or tamper circuit is active while the system is unset.
b) The system needs an engineer or remote reset.
c) A telephone line fault is present.
The 9930 keypad provides the following keys:
9 Used to start a test of the detectors.
8 Used to start a test of the sounders and strobe.
7 Used to enable or disable the Chime facility.
6 Used to set the internal clock calendar, which provides a time stamp
on printed log entries.
5 Used to display the log (250 events).
4 Used to change the user access codes.
YUsed to enter programming and setting/unsetting commands.
XUsed to set the system with individual zones (including 24 hour
zones) temporarily omitted.
ABCD Level setting keys. Level A sets the whole system.
System Features
Detectors
The control unit provides connections for up to eight separate detector
zones. Each zone can be connected as a two wire FSL or a four wire CC with
global tamper. See "4. Programming - Programming Commands" for the
factory default settings and instructions on how to change the zone types and
attributes.
User Control
The control unit provides 16 independent user access codes and or
Scantronic “Prox” tags . The user can change these codes or add or delete
“Prox” tags at any time, but cannot program the system with these codes. The
user can set the system in the following modes:
Full Set All the zones function as programmed during installation.
Part Set B, C & D Selected zones are omitted. You must program the
zones to be omitted during installation.
Set with Omit One or more zones temporarily omitted. The user selects
the zones to be omitted before setting.

Page 6 496929
2. Technical Description
Specification
Environmental -10° to +40 °C.
EN50131 “Class II” 75 % RH.
Dimensions Junior combi box: 243mm W, 234mm H,
87mm D
Weight Junior combi box: 2.45 kg (without standby
battery)
Internal Clock ±10 minutes over one year (depending on the
accuracy of the mains supply frequency).
Conforms to BS4737 1986 Part 1. for Audible or Remote signalled systems.
Designed to fulfil the requirements of a EN 50131-1 Grade 2 Intruder Alarm
System.
Power Supply
All currents accurate to ±5%.
System power supply 230VAC +/- 10% (ambient Temp. 20°. C)
1.0A total.
Control unit power 115mA nominal quiescent, 150mA active.
9930 Remote Keypad 20mA quiescent, 35mA with keypad backlight
on.
Standby Battery 12 Volt, 7.0AH rechargeable lead-acid, Gel
Type battery (not supplied).
Power Supply Type A power supply designed to fulfil the
requirements of EN 50131-1 Grade 2.
Outputs
O/P 1, 2, 3 3 open collector transistor outputs, 500mA,
12VDC, negative applied.
LS Can support two parallel connected externally
mounted 16 Ohm loudspeakers for internal
sounder or EE tones.
AUX 500mA maximum, 12VDC.
Coms OP1-8 12V logic outputs, -ve applied in alarm (+ve
removed).
Inputs
TR = Tamper return for bell.
Tellback/RedCare reset* = +12V applied to operate reset.
Line Fault input = +12V applied to indicate line failure.
Fuses
F1 - 12V AUX 1A Fast.
F2 - Battery 2A Fast.
Caution: When replacing fuses use the ratings quoted above.

2. Technical Description
496929 Page 7
Control Unit PCB
Figures 3 show the layout of the 9651control unit PCB.
BATT F-2A
12V AUX
F-1A
1
2
3
4
5
12
11
10
9
8
7
6
1. Outputs. 7. NVM Reset pins.
2. Aux power. 8. Battery connector.
3. Tamper switch. 9. Battery fuse.
4. Zone connectors. 10. Kick start pins.
5. Keypad bus. 11. 21VAC from transformer.
6. Communications Outputs. 12. 12V AUX fuse.
Figure 3. 9651 Control Unit PCB Layout

Page 8 496929
3. INSTALLATION
Overview
A typical installation comprises the following main steps:
1. Carry out a Risk Assessment of the premises and agree a security grade
for the proposed alarm installation. Decide on positions for wired
detectors, control unit, keypads, external and internal sounders. As part
of the site survey ask the user what facilities they require .
3. Ensure that there is a suitable mains supply present at the site of the
control unit.
4. If you are going to use a communication device (for example a Speech
Dialler) arrange for a PTT (Public Telephone and Telegraph) connection
point near to the control unit.
5. Install the wired detectors and run cables to the control unit. Connect
each detector to its cable.
7. Run cables from the keypads, external and internal sounders to the
control unit.
8. Install keypads and connect them to their cabling. Ensure that each one
has the correct address setting.
9. Install internal and external sounders and connect them to their cabling.
10. Install the control unit and connect it to the mains supply cabling. Do not
apply power at this point.
11. At the control unit, complete all connections to keypads, and sounders.
12. Apply power and program the control unit.
13. Test that the alarm system functions as required.
14. If required, install a communication device (for example a Speech
Dialler), connect it to the PTT network, and check that it functions
correctly.
15. Hand the system over to the user and instruct them in its use.
Cabling Keypads
Cooper Security recommend that you use a minimum 4-core 7/0.2 alarm
cable for wiring keypads.
You can connect the keypads in either a star or bus configuration. If you are
intending to use long cable runs then Cooper Security recommend that you
use star wiring with no more than 300m of cable total for the keypad wiring.
The maximum length of any one run from control unit to the most remote
keypad depends on the number of items connected to the cable. You can
double the maximum length by using two cores each for the 0V and 12V
terminals or by using 16/0.2 cable. The table below shows the maximum