Cornea Systems CT1810 User manual

TABLE OF CONTENTS
ADJUSTING YOUR LCD MONITOR --------------
2
• General safety precautions ………………….…………… 2
• Unpacking your monitor ………………………………… 5
• Viewing angle ……………………………………………… 6
• How to open the back cover ……………………………… 6
• Connecting your monitor ………………………………… 7
• User controls ……………………………………………… 8
• OSD (On-screen display settings) …………….…..……… 9
• Menu adjustments …………………………….…..……… 10
• Refining the picture ………………………….…..……… 12
APPENDIX -----------------------------------
- 13
• Power management function …………….…..……..…… 13
• Video input terminal ……………………………..……..… 13
• Display modes ………………………………….………… 15
• Troubleshooting …………………………………………… 16
• Specifications ……………………………………………… 18

Adjusting your lcd monitor
2
General safety precautions
This Monitor has been engineered and manufactured to assure your safety. Please
read this manual and comply with the warnings and the procedures to avoid any
serious electrical shock and other serious damage.
1.
2.
3.
4.
Do not place anything heavy, wet or
magnetic on the monitor or power cord.
Do not cover the ventilation openings
nor touch them with metallic or
flammable material.
High temperature can cause troubles.
Avoid operating the monitor in extreme
heat, humidity or dusty areas. Extreme
temperature may cause discoloration or
damages.
Ambient Temperature : 0°C ~ 40°C
Do not use a solvent, such as benzene, to
clean the monitor to prevent any
damages to the LCD surface.
Do not use fine tools such as a pin or a
pencil near the monitor to prevent any
scratch to the LCD surface.

Adjusting your lcd monitor
3
5.
6.
7.
8.
Place the monitor on a flat surface to
prevent it from falling.
Do not apply any mechanical shocks to
the machine.
Install it in a well-ventilated area or
secure enough space for ventilation.
Turn the monitor off before connecting it
to the power outlet.

Adjusting your lcd monitor
4
CAUTION : RISK OF ELECTRIC SHOCK, DO NOT OPEN
9.
1 0 .
11.
Make sure that the power cord and the
other cords are properly connected.
Overloaded AC outlets and extension
cords are dangerous. Also, the frayed
power cords and the broken plugs may
cause electric shock or fire.
Do not open the monitor. There are no
user-serviceable components inside.
There is a risk of exposure to high-
voltage electricity inside, even when
power is turned off. If the display
monitor does not operate properly,
unplug the power cord and contact your
dealer. Handling the electrical
equipment carelessly will cause a
serious electrical shock and other
hazards.

Adjusting your lcd monitor
5
Unpacking your monitor
Please make sure the following items are included with your monitor.
If you find that any of these items are missing or appear damaged, contact your
dealer immediately.
The power cord can be different depending upon different voltage areas.

Adjusting your lcd monitor
6
Viewing angle
Your monitor was designed to allow you to adjust it to a comfortable viewing angle.
The viewing angle can be adjusted 5°to 30°forward and backward respectively as
indicated by the arrow marks below.
5° 30°
How to open the back cover
DVI, Power, VGA, Video, S-Video, Audio in, Audio out

Adjusting your lcd monitor
7
Connecting your monitor
Be sure to turn the computer off before connecting the monitor
Cable connections
gConnect the Video cable or S-Video cable to your DVD,VCR or camcorder.
gConnect the video signal cable (15Pin connector) to the system’s VGA
connector which is located on the back panel of the computer.
gConnect the power adaptor cord to the monitor and then to the power supply.
g Insert the audio out jack to the ear phone jack and insert the audio in jack to the
sound card port at the back of the computer, DVD or VCR.
gAfter powering on the computer, DVD or VCR, adjust the display using the
various controls provided. For further information on the installation procedure,
please refer to the operating guide of the computer being used.

Adjusting your lcd monitor
8
User controls
Front control buttons
AUTO MENU SELECT DOWN UP POWER/LED
No. Key name Description
1 AUTO Activates the auto adjustment function.
2 MENU Opens the OSD menu.
3 SELECT Selects the main menu items and sub-menu items.
4 ◀Moves to the lower menu item or sub-menu item.
Decreases the value of the parameter.
5 ▶Moves to the upper menu item or sub-menu item.
Increases the value of the parameter.
6 POWER Turns on/off the monitor.
7 LED
Indicates the status of the monitor.
• Green : Normal operation.
• Amber : Power saving mode or disconnected signal
cable.

Adjusting your lcd monitor
9
OSD (On-screen display settings)
OSD Operation
1. Press the menu button to open the menu system and display the main
function menu.
2. Push the “◀”and “▶” buttons to move between the function icons. As
you move from one icon to the other, the function name changes to
reflect the function or group of functions represented by that icon. See the
menu adjustments table to view a complete list of all the functions
available for the monitor.
3. Push the select button once to activate the highlighted function. Use the
“◀”and “▶” buttons according to the indicators on the menu to make
your changes.
4. To exit from the OSD menu at any time during the operation, press the
auto button. If no keys are pressed for a short period of time, the OSD
menu will automatically disappear.