Craftright CRMSS-1950 User manual
0918
INSTRUCTION MANUAL
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
UNIVERSAL
MITRE SAW STAND
Suitable for mitre saws with up to 380mm wide
base mounting points
Folding legs for easy transport & storage
Extendable supports: 940-1950mm
Adjustable roller height: 810-920mm
Roller width: 250mm
Max. load capacity: 150kg
2
SPECIFICATIONS
Folded Size: 935 x 545 x 805mm
Length: 935mm (folded)
1950mm (extended)
Height: 805mm (folded)
915mm (extended)
Loading Capacity: 150kg
Weight: 9.65kg
SPECIFICATIONS
a. Bolts x 4
b. Washers x 4
c. Spring Washers x 4
d. Hex Nuts x 4
e. Fastening Knobs x 4
Fasteners
KNOW YOUR PRODUCT
a
e
b c d
3
KNOW YOUR PRODUCT
Mitre Saw Stand
1. Mounting Bar
2. Fastening Slot
3. Mounting Bar Handle
4. Extension Arm Locking Pin
5. Roller
6. Material Support Shelf
7. Frame
8. Upper Leg Locking Pin
9. Stand Leg
10.Extension Arm Fastening Knob
11.Lower Leg Locking Pin
12.Extension Arm
13.Roller Arm
14.Roller Arm Fastening Knob
9
8
7
6
3
1
2
4
5
12
10
11
14
13
4
INTRODUCTION
Congratulations on purchasing a Craftright Mitre Saw Stand.
This stand serves as a workstation for holding mitre saws.
WARNING! This stand is intended for use with mitre saws only. Do not use as
a step ladder, stepping stool, storage rack, etc. Craftright will not be liable for
damage or injury caused by improper use of this unit.
SPECIFICATIONS Page 02
KNOW YOUR PRODUCT Page 02
INTRODUCTION Page 04
SAFETY INSTRUCTIONS Page 05
ASSEMBLY Page 07
OPERATION Page 10
MAINTENANCE Page 11
DESCRIPTION OF SYMBOLS Page 11
CARING FOR THE ENVIRONMENT Page 12
CONTENTS Page 12
CONTENTS
5
GENERAL SAFETY WARNINGS
1. Work Area Safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keepchildrenandbystandersawaywhileoperatingapowertool. Distractions can cause you
to lose control.
2. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power
tool.Donotuseapowertoolwhileyouaretiredorundertheinuenceofdrugs,alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b.Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Donotoverreach.Keepproperfootingandbalanceatalltimes. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
h. Donotletfamiliaritygainedfromfrequentuseoftoolsallowyoutobecomecomplacentand
ignore tool safety principles. A careless action can cause severe injury within a fraction of a
second.
WARNING! Read all safety warnings and instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious injury. The
term ‘Power Tool’ in all of the warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless) power tool.
6
MITRE SAW STAND SAFETY WARNINGS
Thisapplianceisnotintendedforusebyyoungorinrmpersonsunlesssupervisedbya
responsiblepersontoensurethattheycanusetheappliancesafely.Youngchildrenshouldbe
supervised to ensure that they do not play with the appliance.
• Always ensure the mitre saw base is properly secured to the stand prior to operation.
• Always ensure the stand legs have been locked into place prior to operation.
• Take care when moving the stand especially when a mitre saw is mounted.
• Do not use the stand for any other purpose than what it is intended for.
• Do not use the stand as a stepping stool or ladder.
• Make sure all moving parts are free from interference.
• Keep hands clear of all moving parts.
• Ensure the Mitre Saw Stand is set up on firm ground in a stable manner.
• Use the Mitre Saw Stand in a dry place protected from the rain.
• Be aware of overbalancing. When a large piece is cut from one end of a job, the
remaining piece may be heavy enough to over-balance the Mitre Saw Stand.
Always ensure the workpiece is well supported.
• When transporting the Mitre Saw Stand in a vehicle, always tie it down to prevent
movement and possible damage.
• Check to make sure that all fixing screws and knobs are tight and all legs are locked into
position before operation.
• The Mitre Saw Stand must be used only for its prescribed purpose. Any use other than
those mentioned in these instructions will be considered a case of misuse.
• Craftright shall not be liable for any damage or injury resulting from such cases of
misuse.
• Craftright shall not be liable for any changes made to the Mitre Saw Stand nor for any
damage resulting from such changes.
7
ASSEMBLY
Unfolding The Stand
1. Lay the mitre saw stand on the floor with the folded legs facing up.
2. Depress the leg locking button
and unfold the 2 upper legs
until the locking button clicks
into place.
3. Repeat the same procedure for
the other 2 legs.
4. Lift the stand and flip it into the upright position.
5. Check that the stand is stable and all of the leg locking buttons have
engaged properly.
Folding The Stand
1 pair of legs on the stand must fold in first for the stand to fold flat. The
legs have not folded into place if the leg locking button does not pop into
place. The legs should not swing about when the stand is picked up if the
legs have locked into position.
1. Turn the mitre saw upside down on the floor with the legs sticking up.
2. Depress the leg locking buttons
on the lower pair of legs and
fold them in.
3. Repeat the same procedure on
the other pair of legs.
8
ASSEMBLY
Attaching The Extension Arms
1. Slide the extension arms into the frame.
2. The locking pin on the extension arms should be facing inwards towards
the centreline of the stand. You will need to depress this twice (once
when the locking pin reaches the frame and again when it pops through
the locating hole further in).
3. Continue sliding the extension arm into the frame
until the desired length is reached.
4. Insert a fastening knob into the hole on the frame
turn it clockwise to secure the extension arm in
place.
5. Insert a roller arm into the collar on the extension
arm. The material support shelf should be facing
inwards towards the centre of the stand.
6. Insert a fastening knob into the bracket and turn
it clockwise to tighten the roller arm into place.
7. Repeat the same procedure with the opposite
extension arm.
9
Attaching The Mitre Saw Mounts
1. Depress the mounting bar handles and hook the
opposite end of the mount onto the frame of the
stand.
2. Lower the handles onto the frame and release
them to lock the mounting bar into place.
3. Repeat the same procedure with the other mounting bar.
Attaching A Mitre Saw
1. Adjust the mounting bars to roughly the width of
the mitre saw base.
2. Place the mitre saw on the mounting bars and
line up the holes in the mitre saw base with the
slots on the mounting bars.
3. Feed a bolt through the bottom of the mounting bar then through the
base of the mitre saw.
4. Slide a washer and then a spring washer onto the
bolt and fasten it with a hex nut.
5. Repeat steps 3 and 4 for the other 3 holes on the
mitre saw base.
ASSEMBLY
WARNING! Only use a mitre saw that has 4 fixing holes (1 in each corner of the
base) on this stand. If the mitre saw does not meet this requirement, do not use it
with this stand as the mitre saw cannot be properly secured. Failure to follow this
direction may result in damage to property and/or personal injury.
WARNING! During operation and before starting a new job, ensure that all screws
and nuts are tightened correctly and securely.
10
OPERATION
Adjusting The Extension Arms
1. Turn the fastening knob on the frame counter-clockwise to loosen it.
2. Pull the extension arm out to the desired length.
Note: The maximum extension length is reached when the arm locking pin
clicks into place. To shorten the extension arm again, depress this pin and
push the extension arm back into the frame.
3. Turn the fastening knob clockwise to tighten it and secure the extension
arm into place.
Adjusting The Roller Height
1. Turn the fastening knob on the collar of the extension arm counter-
clockwise to loosen it.
2. Raise or lower the roller to the desired height.
3. Turn the fastening knob clockwise to tighten it and secure the roller into
place.
Using The Material Support Shelves
The mitre saw stand features material support shelves which allow
repetitive cuts to be made quickly and accurately.
1. Adjust the height of the roller arm so that the lip of the material support
shelf is in line with the work surface of the mitre saw.
2. Adjust the extension arms to the desired cutting length.
3. Place the end of the workpiece against the material support shelf and
commence the cut.
11
DESCRIPTION OF SYMBOLS
MAINTENANCE
Cleaning
1. Wipe away dirt and dust from the Mitre Saw Stand on a regular basis.
Storage
The Mitre Saw Stand can be easily folded for convenient storage and
transportation.
Follow the leg assembly instructions in reverse to fold up the Mitre Saw
Stand.
NOTE: When transporting the Mitre Saw Stand in a vehicle, always tie it down to prevent
movement and possible damage.
NOTE: Craftright will not be responsible for any damage or injuries caused by the repair of the
tool by an unauthorised person or by mishandling of the tool.
Read instruction manual Wear personal protective
equipment
12
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be
disposed of with household waste but in an environmentally
friendly way. Please recycle where facilities exist. Check with
your local council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
Distributed by:
Ozito Industries Pty Ltd
AUSTRALIA (Head Office)
1-23 Letcon Drive, Bangholme Victoria, Australia, 3175
Telephone: 1800 069 486
1 x Universal Mitre Saw Stand
2 x Extension Arms
2 x Rollers
4 x Handle Fastening Knobs
2 x Mounting Bars
4 x Bolts
4 x Washers
4 x Spring Washers
4 x Hex Nuts
1 x Instruction Manual
CONTENTS
Table of contents
