CREATIVE CONCEPTS RSMWT40 User manual

IMPORTANT! For safety reasons, the concrete wall must be capable of supporting the
combined weight of the mount and the display.
3
Display Size: 32” and up
Maximum Load: 55 lbs.
Mounting Pattern: 100 mm x 100 mm to 400 mm x 400 mm
Tilt Range: up to 15°
Profile: 1.8” (4.6 cm)
(A) Drywall Screw (x4)
Washer (x4)
(B) Concrete Anchor (x4)
(C) M4 x 12 Screw (x4)
(D) M4 x 20 Screw (x4)
(E) M5 x 12 Screw (x4)
(F) M5 x 20 Screw (x4)
(G) M6 x 12 Screw (x4)
(H) M6 x 20 Screw (x4)
(I) M6 Washer (x4)
(J) M8 x 12 Screw (x4)
(K) M8 x 20 Screw (x4)
(L) M8 Washer (x4)
(M) Spacer (x4)
IMPORTANT! For safety reasons, this mount must be secured to at least two wood studs
no less than 16” apart. The studs must be capable of supporting the combined weight of
the mount and display.
1
Set the wall plate aside and drill a 1/8” pilot hole at each marked location.
Attach the wall plate to the wall using the drywall screws and washers (A) provided see
Fig. 3). Ensure that the wall plate remains level.
4
Place the wall plate against the wall over the marked studs with the arrow pointing up.
Make sure it is level.
2
5
Part 1A – Mounting to the Wall (Drywall)
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
INSTALLATION
Read these instructions before you begin. If you are unsure of any part of the
process, contact a professional contractor or installer for assistance. Improper
installation can result in injury or damage.
The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where you wish to install the mount
before drilling.
Safety gear and proper tools must be used. Failure to do so can result in injury or
damage.
Two people are recommended for installation. Do not attempt to lift a heavy display
without assistance.
Follow all instructions and recommendations regarding adequate ventilation and
suitable locations for mounting your display. Consult the owner‘s manual for your
particular display for more information.
CAUTION: This wall mount is intended for use only with the maximum weight of 55
lbs. Use with heavier than the maximum weights indicated may result in instability
causing possible injury.
1
2
3
4
5
6
WARNINGS
Wall Plate (x1)
Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
Set the wall plate aside and drill a 5/16” hole at each marked location. Remove any
excess dust from the holes.
Use a high quality stud finder to locate a stud on the wall where you wish to install your
mount (see Fig. 1). Mark both edges of the stud to help identify the exact center.
NOTE: Use the center of the stud to avoid cracking or splitting the wood.
3While another person holds the wall plate in place, mark four locations (two per stud)
for securing the mount to the wall (see Fig. 2).
Fig. 3
1
2
Place the wall plate against the wall in the desired location with the arrow pointing up.
Make sure it is level.
While another person holds the wall plate in place, mark four evenly spaced locations
on the wall for securing the mount (see Fig. 4).
Fig.2
RSMWT40
MEDIUM TILTING WALL MOUNT
INSTRUCTION MANUAL
INTRODUCTION
Congratulations on your purchase!
We take pride in the quality of our products and are confident you have
received one of the finest wall mounts on the market. Should you have any
questions or comments, require any assistance, or need replacement parts for
your mount, please contact us by e-mailing inf[email protected] or calling
1-888-530-7904. You can also visit our website for more information:
www.readysetmount.com.
IF YOU NOT SATISFIED WITH YOUR MOUNT FOR ANY REASON, PLEASE
CONTACT US BEFORE RETURNING IT TO THE RETAILER.
TOOLS REQUIRED
Phillips Head Screw Driver
Electric or Portable Drill
1/8” Drill Bit and Stud Finder for Drywall Installation
5/16” Masonry Bit for Concrete Installation
Level
Fig. 1
Fig. 4

5Attach the wall plate to the wall using the drywall screws and washers (A) provided (see
Fig. 7). Ensure that the wall plate remains level.
B
NOTE: This mount comes with a variety of screw lengths and diameters to accommodate
different display models. Not all of the hardware in the kit will be used. If you cannot find
the appropriate screw size in the kit provided, consult with the manufacturer of your
display or a professional installer.
Part 2 – Attaching the Mount Arms to the Display
IMPORTANT! Use extra care during this part of the installation to avoid damaging your display.
4Insert a concrete anchor (B) into each hole so that it is flush with the concrete surface
(see Fig. 6). A hammer can be used to lightly tap the anchors into place if necessary.
If the back of your display is curved or if additional space is needed between the
display and the mount, use the longer screws.
1
A
B
C
A
Determine the correct length of screw to use by examining the back of your display:
If the back of your display is flat and the mounting holes are flush with the surface,
use the shorter screws from the hardware kit.
Tuck the strings behind the display to hide them from view.
2Determine the correct diameter of screw to use by carefully trying one of each size from
the hardware kit. Do not force any of the screws – if you feel resistance stop
immediately and try a smaller diameter screw.
3Attach the mount arms to the back of your display using the screws identified in steps 1
and 2 (see Fig. 8):
As you face the back of the display, the mount arm marked “R” goes on the right and
the mount arm marked “L” goes on the left.
If you are using the M8 screws you will need to use the M8 Washers (L). If you are
using smaller screws, you will need to use the M6 washers (I).
If you are using the longer screws, you may also need to use spacers (M).
Part 3 – Final Assembly
1
2
With the help of another person, carefully lift your display and place it on the wall plate.
Do not release the display until the mount arms have securely hooked onto the
wall plate.
1
To change the tilt angle of your display, have one person hold the display firmly in place
while another person loosens the tilt adjustment knobs located on each mount arm.
Once loosened, move your display to the desired position and then re-tighten the
knobs. Do not release the display until both knobs are fully tightened. If you are
unable loosen or fully tighten the knobs by hand, the Phillips Head Screw Driver can
also be used (see Fig. 9).
Make sure the safety clips located at the bottom of each mount arm are fully
engaged to prevent the display from being accidentally knocked from the
mount. Pulling down on the strings will disengage the safety if you need to remove the
display from the wall.
IMPORTANT! Do not cut or otherwise remove the strings or you may be unable to
remove the display from the mount.
IMPORTANT! Never fully loosen or remove the tilt adjustment knobs.
3
Periodically clean your mount with a soft, dry cloth. Inspect all screws and hardware at
regular intervals to ensure that no connections have become loose over time.
Re-tighten as needed.
2
RSMWT40 Rev 20151014
Fig. 5
Fig. 6
Fig. 7
Fig. 8
For displays with curved or
recessed backs.
For displays with
flat backs.
OPERATION AND ADJUSTMENT
Fig. 9