Crimson LASERLYTE QUICK TYME TLB-QDM User manual

QUICK TYME®LASER TRAINER TARGET TLB-QDM
QUICK TYME®LASER TRAINER TARGET TLB-QDM
®
®
QUICK TYME
Display
Start
Timer
Reset
Set Timer
G
DC
B
A
E
F
KEY FEATURES
A: ON/OFF SWITCH
B: TARGET AREA
C: START/DISPLAY
D: RESET/SET TIME
E: WALL HANGER
F: BATTERY COMPARTMENT
G: DO NOT UNSCREW
THESE SCREWS

QUICK TYME®LASER TRAINER TARGET TLB-QDM
L27-00070_000 07/19© 2019 Crimson Trace. All rights reserved.
9780 SW FREEMAN DRIVE ■WILSONVILLE, OREGON 97070
833-278-5470 ■FAX: [phone] ■LASERLYTE.COM
™
3 YEAR LIMITED WARRANTY
Crimson Trace Corporation warrants that this LASERLYTE® product will be free from defects in
materials and workmanship for a period of three (3) years from the date of manufacture or, upon
presentment of a dated sales receipt, from the date of original retail purchase. For complete
warranty terms and conditions pleasewww.laserlyte.com/warranty, or contact us at the address /
telephone number listed below.
For warranty service call Customer Service at 833-278-5470, or email [email protected] for a
Return Authorization Number (RMA).

QUICK TYME®LASER TRAINER TARGET TLB-QDM
™
QUICK TYME®TARGET
TLB-QDM USER GUIDE

QUICK TYME®LASER TRAINER TARGET TLB-QDM
TLB-QDM TARGET USAGE
• QUICK TYME®Mode
5 Second Score Mode
10 Second Score Mode
15 Second Score Mode
• Laser Tracer Fire Mode
QUICK TYME®MODE
1. Turn QUICK TYME®TARGET to ON.
2. Fire laser in the SET TIME circle (lower right). Timer will
display 9.9 seconds.
3. Fire laser at the START circle (lower left). After the beep, you
have 9.9 seconds to fire a shot.
4. Once you fire a shot at the target, it will display the shot time.
Fire laser in the Set Timer/Reset circle to continue training.
5. Fire red laser dot in the RESET/SET TIME circle to continue
training.

QUICK TYME®LASER TRAINER TARGET TLB-QDM
LASER TRACER FIRE MODE
1. Turn QUICK TYME® TARGET to ON.
2. Fire 2 shots at the Reset circle. Ensure Timer displays
0.0 Seconds.
3. Begin firing laser at target.
4. Fire laser at Display circle to see shots on target.
5. Fire laser at Reset circle to clear the target and continue training.
TROUBLESHOOTING
• Be sure the TLB-QDM Laser Target is in proper lighting conditions.
• A strong light source may affect the TLB-QDM’s ability to
register “hits”. Conditions may vary.
TLB-1
TLB-1
®
Laser
Target
Display
OFF ON
Reset
®
Laser
Target
Display
OFF ON
Reset

QUICK TYME®LASER TRAINER TARGET TLB-QDM
BATTERY WARNINGS
WARNING: KEEP BATTERIES AWAY FROM CHILDREN. THERE IS
A CHEMICAL BURN HAZARD ASSOCIATED WITH BATTERIES.
• When used correctly, batteries provide a safe and dependable source of
portable power. However, misuse or abuse may result in leakage, re, or
explosion.
• Batteries can explode or leak and cause burns if installed backwards,
disassembled, charged, or exposed to water, re or high temperature.
• Always take care to install your batteries correctly observing the “+” and
“-” marks on the battery and the device.
• Always replace the whole set of batteries at one time, taking care not to
mix old and new batteries, or batteries of different types.
• Store unused batteries in their original packaging and away from metal
objects that may short-circuit them.
• Remove discharged batteries from equipment promptly to avoid possible
damage from leakage.
• Never dispose of batteries in re. (Failure to observe this precaution may
result in an explosion.)
• The batteries are supplied in a charged state, and are not designed for
recharging. Recharging may cause leakage, re, or explosion.
• The batteries should be disposed of properly, including keeping them
away from children.
• Dispose of used batteries immediately. Even used batteries can cause
injury.