DIY C007 User manual

C007 Instruction Manual
DIY handmade goods – –
Cocoa's Fantastic Ideas
DIY handmade goods – –
Cocoa's Fantastic Ideas

1. LED wiring indication:
White=Positive;Grey=Negative.
2.Use a craft blade to carefully
skim over the plastic to bare the
copper wire.
3. For LED wiring extension,
please refer to the below steps:
Making tips
Twist the copper of
both LED wire and
extension wire
together.
Do the same on the
white wire.
Remarks: Tie a knot
at the end of the grey
wire to differentiate
the polarity.
Place the duly twist
wire on the tapes
provided.
Roll and wrap the
wire.
Place another wire
next to it.
Remarks: DO NOT
contact both copper
wire to avoid short
circuit.
Roll and wrap it together.
The product is not suitable for children
under 14 years old. The should be under
custody of adults when playing with the
product.
There are small parts, please do not swallow
them for avoiding dangerous accidents.
1.Picures shown on the package may
be slightly different from the actual
product.
2.Please use the provided tracing
paper for cutting purpose to achieve
the best
outcome.
3.Product designs and specification
may be subject to change without
advance notice for purpose of making
improvement.
4.Testing on LED function:
Warnings
Tips for assembling
DO NOT contact the
LED wire end direct
to the battery cell.
Use the provide battery
holder. Make sue the
correct polarity.
How to assemble the battery holder
1.Material and tools needed:
- Battery holder, LED bulb,
tape.
2.Twist the following wire together:
(I) WHITE wire from the battery box
with the GREY wire from LED bulb.
(II) GREY wire from the battery box with
the WHITE wire from LED bulb.
3.Wrap the exposed wire
with the tapes.
4.Tear off the rubber paper
Rubber paper
5.Set the black key on the
battery box to one side
of “ON” as shown.
6.Ture on the power and
complete the installation.
LED
wire
Extension
wire
LED
wire
Statement: the lamp wires cannot be inserted into the
output socket.
– – Please notice the place of anode and cathode when pit in the batteries
– – Rechargeable batteries are not blunt electricity
– – Rechargeable batteries can only be charged under adult supervision
– – Rechargeable batteries should be removed from the toy before charging
– – Different types of batteries cannot mix; Do not mix new batteries in use with
semi-used batteries.
– – Run out of battery should be removed from the toy
– – The power shall not be short circuit

Product information
Sign
Shop
Sign
Floor sign
Sun umbrella
Bag
Railing
Chocolate
tray
Chocolate
lollipop
Chocolate Chocolate
biscuit
Chocolate
sauce
Chocolate Chocolate
Street light
Gift box
Chair
Flower pot
Flower
groove
Flower
groove
Cart

Cabinet
Cut F14 two
pieces with
0.5cm long.
Use a pencil to draw the D07 in four, so as to make easy.
(it is recommended that the A09-03 and A09-06 be put in the cabinet and then glued on D13 as shown.
Chocolate A
Chocolate B
Chocolate cup

Cut F04 two
pieces with
1.5*1.5cm. Cut G19 two
pieces with
1.1cm long
Chocolate sauce
Circular gift box
Cut F08
Gift box
Attach the excess to the back.
G19

Display cabinet
Cut out A07 according
to the template A09-11
as shown.
Draw a crease with a knife according to
the dotted line on the template paper
as shown.
Chocolate cake
(Color can be random with
picture for reference only.)
Chocolate C
Press the four sides gently with your
fingers so that the bag bulges as shown.
Chocolate biscuit
Fold A09-14-1 and A09-14-4 in half before
cutting as above shown.

(Color can be random with
picture for reference only.)
Chocolate platter
Chocolate lollipop
Cut out F12
Poke nine holes in box as shown.
(Color can be random with
picture for reference only.)
Chocolate box
Little flag
Cut F11 out with 3.7cm Bread F11 into
two pieces as shown.
Fold A09-17 in half before cutting.
Cart

Heart chocolate
F04
1.5*1.5cm
Knead the F04 into small balls as shown.
Chocolate tower
Cut F05 according to the
template A09-19 as shown. (Color can be random with
picture for reference only.)
The making method of bow,
please refer to page 4.
Counter
Chocolate D
Chocolate tray (Color can be random with
picture for reference only.)
The making method of A09-22,
please refer to A09-07(Page 4).
Sunshade
Cut out F14 with 10cm
Cut out F14 with 4.8cm
Cut out F14 with 4.7cm
Cut out F15 with 4.5cm

Cut F01 according to the template of A09-24 as shown.
Cut F14 with 9.8cm long as shown.
To cut a small opening at
the top of A09-27-1 with
scissors as shown.
Book
Chocolate ice cream
(Color can be random with
picture for reference only.)
Bread F11 into
two pieces as shown.
The making method of A09-28,
please refer to Page 7.
Bag
Cut F11 with 3.5cm

Tulips
Cut out F02 with
4*5.3cm
Cut out F02 with
2.5*7cm
Cut out F13 with Cut F02 according to the
template of A09-30 as shown.
(Please note that F02 has a vertical line)
Flower
Cut out F02 with 2*7.5cm
Cut out F02 with 2*12cm
*please note that the F02 has a vertical line. Scratch the upper part of the leaf with
your finger to make it slightly curly as
shown.
Cut F03 according to the
template of A09-31 as shown.
(Please note that F03 has a vertical line)
Wall deco
Floor signSign
Window
Cut A07 according to the
template of A09-34 as shown.
The making method of little flag,
please refer to Page 6.

Shade
Door
Roof sign
The making method
of bow, please refer
to page 4.
Cut A07 according to the
template of A09-37 as shown.
Fence
Roof

Top lamp
Outer frame
Cut A07 according to the
template of A09-40 as shown.
G12
G14

Music machine core manual guide
(If you hav e p urchased the music
machine core, please fix it firstly)
(front view)
(back view)
Window
Shop sign
Cut F11 with 2.5cm long

Beak the F11 into two pieces.
Street
light
Rubber paper
Tear off the rubber paper,
and fix H02 on the board as shown.
Trim all the LED wiring to the same length.
Use a craft blade to carefully skim over the plastic to bare
the copper wire. Twist the same color wire together.
Twist the following wire together:
(I) WHITE wire from the battery box with the GREY wire
from LED bulb.
(II) GREY wire from the battery box with the WHITE
wire from LED bulb.
Roll and seal the duly twist
copper with the white tape provided.
GREY wire
from LED
bulb
WHITE wire
from LED bulb
WHITE wire
from battery box
GREY wire
from battery box
Door Fence
Cart
Fence
Fence

Photo
Gallery
2.Paste J04 andJ05 together to
complete the dust proof cover as shown.
1. Tear off kraft paper of each
piece of transparent cover.
J04 Transparent cover
0.18*16*20 (3pieces)
J05 Transparent cover
0.18*15.64*16(2pieces)
Photo of Dust proof cover
Installation of dust proof cover
(For updated version, the parts need to be purchased separately)
Floor
sign
Bag
Flower
Flower Bag Flower
Sunshade

Attention: Please keep the instruction
manual for future enquires after installation.