Dr. dunk A series User manual

Heavy-Duty

Basketball Stand

SBA305 - A series

User Manual

[Revision 2.0 March 2020]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this

manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Video Tutorial:

Assembly

Heavy-Duty Basketball Stand - SBA305 - A Series

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death,

injury or equipment or property damage if not understood or followed. Safety messages have the

following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the

product, including safety warnings, and

any assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery

powered or combustion engine powered.

•Before Use - If you are not familiar with

the safe operation/handling of the

equipment, or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

•Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

•Keep clear of moving parts.

•Equipment may be a potential source

of electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

•Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

•Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

•Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

•This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

•Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

•Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

•The equipment is designed for

domestic use only.

•Handle the equipment safely and

carefully.

•Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

•Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

•Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

•Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where

applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

•The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and

care, see Equipment Safety.

Heavy-Duty Basketball Stand - SBA305 - A Series

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

•Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and

safety codes.

•Wherever possible, use a residual

current device (RCD).

•High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

•Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

•Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

•Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift,

move or carry equipment.

•Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

•Do NOT attempt any maintenance or

repair work not described in this

manual.

•After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect

spark plugs and/or electrical power

sources and/or batteries from it before

making adjustments, changing

accessories or performing repair or

maintenance.

•Do NOT make adjustments while the

equipment is running.

•Perform service related activities in

suitable conditions, such as a

workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Basketball Stand Safety

•Owner must ensure that all players

know and follow these rules for safe

operation of the system.

•To ensure safety, do not attempt to

assemble this system without following

the instructions carefully.

•Check entire box and inside all packing

material for parts and/or additional

instruction material.

•Before beginning assembly,read the

instructions and identify parts using the

hardware identifier and parts list in this

manual.

•Proper and complete assembly, use,

andsupervision are essential for proper

operation and to reduce the risk of

accident or injury.

•A high probability of serious injury

exists if this system is not installed,

maintained, and operated properly.

Basketball Stand Safety

•The system should be moved by at

least 3 adults capable of handling its

weight. children should not be allowed

to move the system.

•Stand in front of the system and pull

the pole forward until the system is

balanced on its wheels.

•Move the system to the desired

location and carefully set the base

down.

•Never hang from the rim or climb on the

pole as injury or property damage could

occur. For these reasons do not

perform dunking activities on this

system as it is not designed for such

use. Do not allow children to climb on

the basketball system.

•Never leave the unit assembled without

weight in the tank.

Basketball Stand Safety

•Check the base frequently for leaks or

loose cap. Slow leakage could cause

the system to tip over unexpectedly

and damage the floor if used inside.

•Seat the pole sections properly. Not

doing so might allow the pole sections

to separate during play or during

transportation for this system.

•Further check before each use if all

fittings and hardware are tight.

•Climate, corrosion or misuse could

result in system failure.

•This system is not intended for children

3 and under.

•All players must use sufficient bodily

protection when playing.

Heavy-Duty Basketball Stand - SBA305 - A Series

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols

on your product and their meanings. If any stickers become unreadable, unattached etc, replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protectiove

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenence etc.

Heavy-Duty Basketball Stand - SBA305 - A Series

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

maneouvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenence etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Dorect

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser, or allow

others to.

Heavy-Duty Basketball Stand - SBA305 - A Series

Table of Contents

Safety ................................................................................................................................................2

Safety Symbols ............................................................................................................................................4

Parts Identification...........................................................................................................................7

Assembly and Set-Up ....................................................................................................................11

Operation ........................................................................................................................................16

Height Adjustment......................................................................................................................................16

Moving the Basketball Stand......................................................................................................................16

Reference Images......................................................................................................................................17

Specifications.................................................................................................................................18

Heavy-Duty Basketball Stand - SBA305 - A Series

Parts Identification

Part No Name & Specification Qty. Remarks

A1, A2, A3, A4 M12*180MM 1 Connect backboard brace (longer) (T) & outer lifter

pole (EE)

B1, B2, B3, B4 M12*180MM 1 Connect link block of top pole (Z) & backboard

brace (shorter) (S)

C1, C2, C3, C4, C5 M12*180MM 2 Connect backboard (CC) & backboard brace (S, T)

D1, D2, D3 M12*180MM 1 Connect link block of top pole (Z) & backboard

brace (longer) (T)

E1, E2 M12*180MM 1 Connect large spring (HH) on the middle of

backboard brace (shorter) (S)

F1, F2, F3 M10*100MM 2 Connect top pole (W), middle pole (X) & bottom

pole (Y)

G1, G2, G3 M10*120MM 1 Connect middle pole (X) & pole brace (U1, U2, U3,

U4)

H1, H2, H3 M8*90 MM 2 Connect rim (AA) & backboard (CC), add small

spring (R)

J1, J2, J3 M8*100MM 2 Connect triangular block (Q) & middle pole (X)

K1 – K4 M10*100MM 1 Connect link block of top pole (Z) & top pole (W)

L1, L2, L3 M8*45MM 1 Connect triangular block (Q) & inner lifter pole (FF)

M1, M2, M3 M8*20MM 2 Connect rim (AA) & backboard (CC)

N1, N2 M8*25MM 4 Connect middle pole (X) & pole brace (U1, U2, U3,

U4)

O1, O2 M8*30MM 1 Connect base (BB) & bottom pole (Y)

M Wheel 2

N Cap for top pole 1

O Water cap 1

P Net 1

Q Triangular block 1

R Small spring 2

S Backboard brace (shorter) 2

T Backboard brace (longer) 2

U Pole brace (U1, U2,

U3, U4) 4

V Wheel Shaft 1

W Top Pole 1

X Middle Pole 1

Y Bottom Pole 1

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Part No Name & Specification Qty. Remarks

Z Link block of top pole 1

AA Rim 1

BB Base 1

CC Backboard 1

DD Protector pad 1

EE Outer lifter pole 1

FF Inner lifter pole 1

GG Wheel bracket 2

HH Large spring 2

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

NOTE: Please measure all hardware and check the you have the correct quantities before starting assembly.

Some spacers may not be on the bolts as shown. Disassemble and re-assemble where needed.

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Assembly and Set-Up

Connect the top pole (W), middle pole (X)

and bottom pole (Y). Pay close attention to

the direction of these three poles. The holes

on the end connectors must overlap together

to be more convenient to the next installation

of fixed bolts.

Install the triangular block (Q) on the middle

pole (X) with bolts J1, J2 and J3.

When the pole joint

has a burr or pipe end

deformation, strike the

bottom of the pole

firmly 3 to 4 times on a

piece of wood or

cardboard.

Secure the top pole (W), middle pole

(X) and bottom pole (Y) together with

bolts F1, F2, and F3.

Install the bottom pole (Y) on the

base (BB) with bolts O1 and O2,

ensuring that the triangular block (Q)

is facing backwards after installation.

Fix the pole braces (U1, U2, U3,

U4) on the middle pole (X) with

bolts G1, G2, and G3. The top end

of U1 and U2 must be fixed inside

the pole brace (U3, U4), near the

middle pole (X).

Insert wheel shaft (V) into

wheel (M), base (BB) &

wheel bracket (GG) one-by-

one.

Secure the pole braces U1,

U2, U3, U4 on base with

bolts N1, N2, N3, N4. Note

that the pole braces U1 ,U2

are fixed on the two sides of

base (BB) & the wheel

bracket (M) must be fixed

with the bottom end of pole

braces U3, U4 together.

Video Tutorial:

Assembly

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Secure the rim (AA) on the backboard (CC) with bolts H1 – H3 and M1 – M3. Note that the 2pcs. Of

small springs (R) must be installed on the top 2 holes of the rim (AA) with bolts H1 – H4).

Secure the 4pcs. Of backboard braces (S, T) on the back of the backboard (CC) with bolts C1 – C5.

Note the place of bushing (C3). Secure bolts E1, E2 to the middle holes of the backboard brace

(shorter) (S) for the following step of hanging the large spring (HH).

NOTE: The bottom hole sizes will help you

determine which end of the backboard brace

(S, T) should be installed on the back of the

backboard (CC).

Refer reference image A3 page 18.

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Install the link block (Z) at the top end of the top pole (W)

with bolts K1 – K4. The bushing (K2) must be put at the

side of the top pole with bolt K1 to prevent the top pole

from bending out of shape. Do not secure the bolt K1 too

tightly before securing the pole brace (S, T) first.

Connect the backboard brace (S, T) on the link block of

the top pole (Z) with bolts B1 – B4 and D1 – D3. The

bushing (B2) must pe put inside the link block (Z) with bolt

B1 to prevent the link block (Z) to bend out of shape.

Finally, install the cap on the top pole (W).

Secure the top of the outer lifter pole (EE) to the

backboard brace (longer) (T) with bolts A1 –

A4. The bushing A2 must be between the

backboard (longer) (T) and the outer lifter pole

(EE).

Secure the inner lifter pole (FF) to the triangular

block (Q) with bolts L1 – L3.

Do not tighten nut all the way. It will need to

be removed when adding tensioning springs

in the next step.

Refer reference

image A1 on page 17

Refer reference image

A2 on page 17

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

This end should

face the backboard.

Hang the other end of the large spring (HH) on

bolt E1 with a wrench.

Remove the bolt holding the lifter pole. This will

allow you to adjust the distance between the

backboard and the spring. Once the spring is

attached, you can re-secure the bolt and use

the height adjuster as normal.

Hook the 2pcs. of large springs (HH) on the fourth hole of

the backboard bracket.

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

For safety reasons, it is recommended to fill up the tank with sand instead of

water. If a small leak develops, water might run, allowing the stand to fall over and

cause personal injury and /or death or property damage. Place the base on a smooth surface

only, away from any sharp objects that might be able to puncture it.

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Operation

Height Adjustment

As shown in the image below, hold the lifting handle bar (EE) and move it up or down.

Moving the Basketball Stand

1. Adjust the basketball stand to its lowest height level before moving it.

2. Avoid making friction with the ground while moving.

3. Move the basketball stand to the preferred location, then slowly raise it up to the preferred height.

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Reference Images

Height adjuster should be

facing the rear of the unit

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Specifications

Material Steel Frame and Rim

Backboard Shatterproof polycarbonate

Net Nylon

Backboard Dimension 130 x 80cm

Backboard to ground Height Adjustment 295-370cm

Rim to ground Height Adjustment 230cm-305cm

Main Tube Diameter 8.6cm

Rim Inner Diameter 45cm

Note: Assembly Required

DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK DR. DUNK

Heavy-Duty Basketball Stand - SBA305 - A Series

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Dr. Dunk A Series User manual

Popular Sport & Outdoor manuals by other brands