EG4 BRIGHTMOUNT User manual

EG4 ELECTRONICS | INSTALLATION GUIDE
EG4 BRIGHTMOUNT
ADJUSTABLE GROUND MOUNT SYSTEM
PARTS
1
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
2) Mid Clamp 3) End Clamp
4) Mount Group 5) Grounding Lug Group 6) Grounding Clip
7) Anchor Bolt
M10*100
8) L Foot Group 9) Splice Connector and
Bonding Jumper
1) Rack Rail

EG4 ELECTRONICS | INSTALLATION GUIDE
DIMENSIONS AND LAYOUT
2
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
ENGINEERING DRAWINGS

EG4 ELECTRONICS | INSTALLATION GUIDE
3
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
LAYOUT AND INSTALLATION
OVERALL LAYOUT
Torque Recommendations:

EG4 ELECTRONICS | INSTALLATION GUIDE
INSTALLATION
A) Leg Group
Assembly
Use M8*80 bolts, M8
spring washers, flat
washers, and M8 nuts to
install the U connectors as
shown in the illustration to
the right.
4
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
The adjustable leg is used to change the angle of the array.
Adjustment instructions are on the following page.
Use M8*65 bolts, M8
spring washers, flat
washers, and M8 nuts to
install the mount group as
shown in the illustration
to the left.

EG4 ELECTRONICS | INSTALLATION GUIDE
INSTALLATION
5
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
Loosen set screws to
adjust the angle of the
array. Different angles
correspond to the lengths
provided in the chart
below. The recommended
torque for the set screws
is 80 in. lbs. (9 Nm).
Note: Both set screws
must be secured to lock
the adjustable leg in
place.

EG4 ELECTRONICS | INSTALLATION GUIDE
6
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
INSTALLATION
Use M8*80 bolts, M8
spring washers, flat
washers, and M8 nuts
to install L feet as
shown in the
illustrations to the
right.
Use the provided anchor bolts to
secure mounting brackets to the
concrete anchors.

EG4 ELECTRONICS | INSTALLATION GUIDE
7
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
INSTALLATION
B) Rail Assembly
Follow the diagrams to secure the
rails to the previously installed L feet.
Use the splice connectors to join rail
sections together, leaving a 0.1 – 0.2
in. (3 – 5 mm) expansion gap between
rail joints.
Completed rail
assembly.

EG4 ELECTRONICS | INSTALLATION GUIDE
8
www.eg4electronics.com
Version 1.0.0 | Specifications subject to change without notice.
© 2023 EG4 Electronics, LLC. All rights reserved.
PV ATTACHMENT
Install PV modules
using the end clamps
and mid clamps along
with the grounding
clips to secure them to
the mounting rails.
Follow the steps
illustrated to the right
for proper installation.
Install grounding lugs on
the end of the rails to
attach a grounding wire
for proper array
protection.