EINHELL BT-CD 18/2 Li User manual

Original operating instructions
Cordless Drill
BT-CD18/2 Li

Art.-Nr.: 45.134.65 I.-Nr.: 11011
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 1

2
1
7
16
2
3
2 3
4
4
5
1
6
2
1
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 2

3
4 5
a
7
2
3
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 3

“Caution - Read the operating instructions to reduce the risk of injury”
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Wear a breathing mask.
Dust which is injurious to health can be generated when working on wood and other materials.
Never use the device to work on any materials containing asbestos!
Wear safety goggles.
Sparks generated during working or splinters, chips and dust emitted by the device can cause
loss of sight.
4
Change the gear only when the drill is at a standstill. If you fail to observe this point, the gearing
may be damaged.
GB
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 4

5
GB
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
1. Safety regulations
The corresponding safety information can be found
in the enclosed booklet.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
Hold the equipment by the insulated handles
when carrying out work during which the screw
or the plug-in tool could strike concealed power
cables. Contact with a live cable may also make the
metal parts of the equipment live and cause an
electric shock.
2. Layout / Items supplied (Fig. 1/2)
2.1 Layout
1. Torque selector
2. Forward/Reverse switch
3. ON/OFF switch
4. Battery pack
5. Pushlock button
6. Selector switch for 1st gear to 2nd gear
7. Quick-change drill chuck
2.2 Items supplied
nOpen the packaging and take out the equipment
with care.
nRemove the packaging material and any
packaging and/or transportation braces (if
available).
nCheck to see if all items are supplied.
nInspect the equipment and accessories for
transport damage.
nIf possible, please keep the packaging until the
end of the guarantee period.
IMPORTANT
The equipment and packaging material are not
toys. Do not let children play with plastic bags,
foils or small parts. There is a danger of
swallowing or suffocating!
nCordless Drill
nOriginal operating instructions
ncharger (1x in set included)
nBattery Pack (2x in set included)
3. Proper use
The cordless drill/screwdriver is designed for
tightening and undoing screws, as well as for drilling
in wood, metal and plastic.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Voltage supply 18 V d.c.
Idling speed: 0-400/0-1150 rpm
Torque settings: 25+1
Forward and reverse rotation yes
Chuck capacity 13 mm
Weight 1.2 kg
Max. screw diameter: 6 mm
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
LpA sound pressure level 76 dB(A)
KpA uncertainty 3 dB
LWA sound power level 87 dB(A)
KWA uncertainty 3 dB
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 5

GB
6
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Drilling in concrete
Vibration emission value ah≤ 2.5 m/s2
K uncertainty = 1.5 m/s2
Screwing without hammer action
Vibration emission value ah≤ 2.5 m/s2
K uncertainty = 1.5 m/s2
Additional information for electric power tools
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
nOnly use appliances which are in perfect working
order.
nService and clean the appliance regularly.
nAdapt your working style to suit the appliance.
nDo not overload the appliance.
nHave the appliance serviced whenever
necessary.
nSwitch the appliance off when it is not in use.
nWear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment’s
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
5. Before starting the equipment
Charge the battery pack with the charger supplied. An
empty battery pack requires a charging period of
approximately 1 hours.
For more details about charging the battery pack
please read the operating instructions of the 1-hour
charger.
Always remove the battery pack before making
adjustments to the equipment.
Mounting and removing the battery pack
(Fig. 2/Item 4)
Mounting:
Push the battery pack (4) onto the equipment until it
latches in place.
Removing:
Press the pushlock button (5) and pull the battery
pack (4) out of the equipment.
6. Operation
6.1 Torque setting (Fig. 3 / Item 1)
The cordless drill is fitted with a mechanical torque
selector.
The torque for a specific size of screw is selected
with the torque selctor (1). The correct torque
depends on several factors:
non the type and hardness of material in question
non the type and length screws used
non the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
6.2 Drilling (Fig. 3 / Item 1)
For drilling purposes, move the torque selctor (1) to
the last step „Drill“. In this setting the slip clutch is
inactive. The maximum torque is available in drilling
mode.
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 6

7
GB
6.3 Forward/Reverse switch (Fig. 4 / Item 2)
With the Forward/Reverse switch (2) above the
On/Off switch (3) you can select the direction of
rotation of the battery-powered drill and secure it
against being switched on accidentally. You can
choose between clockwise and anticlockwise
rotation. To avoid causing damage to the gearing it is
advisable to change the direction of rotation only
when the tool is at a standstill. The On/Off switch (3)
is blocked when the Forward/Reverse switch (2) is in
centre position.
6.4 On/Off switch (Fig. 4 / Item 3)
Infinitely variable speed control is possible with the
On/Off switch (3). The further you press the On/Off
switch (3), the higher the speed of the battery-
powered drill.
6.5 Changing the accessory (Fig. 5)
Important. Set the Forward/Reverse switch (2) to its
centre position whenever you carry out any work (for
example changing the accessory, maintenance work,
etc.) on the cordless drill.
nThe cordless screwdriver is fitted with a quick-
change chuck (7) with an automatic spindle stop.
nOpen the chuck (7). The chuck opening (a) must
be large enough to hold the accessory (drill bit or
screwdriver bit).
nSelect the suitable accessory. Push the
accessory as far as possible into the chuck
opening (a).
nTighten the chuck (7) and then check that the
accessory is secure.
6.6 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described in section 6.1 in these operating
instructions, to suit the size of screw.
6.7 Selecting 1st gear to 2nd gear (Fig. 3/Item 6)
By adjusting the selector switch (6), you can work
with a faster or slower turning speed. Change the
gear only when the drill is at a standstill. If you fail to
observe this point, the gearing may be damaged.
7. Cleaning, maintenance and
ordering of spare parts
Always remove the battery pack before starting any
cleaning work!
7.1 Cleaning
nKeep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
nWe recommend that you clean the device
immediately each time you have finished using it.
nClean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
nType of machine
nArticle number of the machine
nIdentification number of the machine
nReplacement part number of the part required
For our latest prices and information please go to
www.einhell.com.au
8. Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
9. Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing
temperature. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 7

8

The reprinting or reproduction by any other means, in whole or in part,
of documentation and papers accompanying products is permitted only
with the express consent of ISC GmbH.
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 8

9
 Technical changes subject to change
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 9

10
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 10

11
The guarantee provided in this Guarantee Certificate is given by Einhell Australia Pty Limited
ACN 134 632 858 of 6/166 Wellington Street, Collingwood, Victoria (Telephone number 1300 922 271)
(Einhell Express Guarantee)
tGUARANTEE CERTIFICATE
Dear Customer,
All of our products undergo strict quality checks. In the unlikely event that your device develops a fault, please
contact our service department at the address shown on this guarantee certificate. Of course, if you would
prefer to call us then we are also happy to offer our assistance under the service number printed below.
Please note the following terms under which claims under the Einhell Express Guarantee can be made:
1 The benefits conferred by the Einhell Express Guarantee are in addition to all rights and remedies which
you may be entitled to under the Australian Consumer Law, and any other statutory rights you may have
under other applicable laws. This Einhell Express Guarantee does not exclude, restrict or modify any
such rights or remedies.
We do not charge you for the Einhell Express Guarantee.
2. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
3. The Einhell Express Guarantee only covers problems caused by material or manufacturing defects, and
our liability under the Einhell Express Guarantee is limited, at our discretion, to the rectification of these
defects or replacement of the product. Please note that the product has not been designed for use in
commercial, trade or industrial applications. Consequently, the Einhell Express Guarantee will not apply
if the product is used in commercial, trade or industrial applications or for other equivalent activities.
4. The following are also excluded from the Einhell Express Guarantee: compensation for transport
damage, damage caused by failure to comply with the installation/assembly instructions or damage
caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to
the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the
product or use of non-approved tools or accessories), failure to comply with the maintenance and safety
regulations, ingress of foreign bodies into the product (e.g. sand, stones or dust), effects of force or
external influences (e.g. damage caused by the product being dropped) and normal wear resulting from
proper operation of the product. The Einhell Express Guarantee will also not apply if any attempt is made
to tamper with the product.
5. The Einhell Express Guarantee is valid for a period of 2 years starting from the purchase date of the
product. Claims made under the Einhell Express Guarantee should be submitted before the end of this
guarantee period and within two weeks of the defect being noticed. No claims under the Einhell Express
Guarantee will be accepted if submitted after the end of this guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such
cases, the work performed or parts fitted will not result in an extension of the guarantee period for the
Einhell Express Guarantee, and the Einhell Express Guarantee will not apply for the work performed or
parts fitted. This also applies when an on-site service is used.
6. To make a claim under the Einhell Express Guarantee, please send the relevant product postage-free to
the address shown below and enclose either the original or a copy of your sales receipt or another dated
proof of purchase. It would help us if you could describe the nature of the problem in as much detail as
possible. If the defect is covered by the Einhell Express Guarantee, your product will be repaired
immediately and returned to you, or we will send you a new device (at our election).
Any costs incurred by you in making a claim under this Einhell Express Guarantee, unless specified
otherwise in this guarantee certificate, must be borne by you.
Of course, we are also happy to offer a chargeable repair service for any defects which are not covered by the
scope of the Einhell Express Guarantee or for products which are no longer covered by the Einhell Express
Guarantee. To take advantage of this service, please send the product to our service address.
EINHELL AUSTRALIA PTY LTD
6/166 Wellington Street- Collingwood VIC 3066
Australia - Phone: [phone]
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 11

EH 04/2012 (02)
Anleitung_BT_CD_18_Li_EX_AUS__ 03.05.12 09:57 Seite 12