ELAN Lighting TRANSCEIVER WS User manual

TRANSCEIVER WS
RECEIVER WS
User manual

On the Transmitter, press and hold the FUNCTION button until LINK begins ashing. All
registered Receivers linked to that Transmitter will be unlinked.
3.4 To unlink all Receivers
The TRANSCEIVER can be used as a Transmitter or Receiver. To switch mode between
Transmitter and Receiver, power o the unit, then hold the FUNCTION button while power on
the unit for 2 seconds. When DMX and MODE indicators turn o, then the unit is a Receiver.
Otherwise, it is a Transmitter.
3.5 To set a TRANSCEIVER to Transmit or Receive
IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that old
appliances contain and reduce the impact on human health and the
environment, ensure that this product is recycled at the end of its life.
5. Specifications
FCC Notice
5
• Frequency band: 2.4GHz
• Transmission distance: approx. 500m
• IP rating: IP20
• Power supply: AC 230V 50-60Hz
• Dimension: 145mm x 100mm x 57mm
• Weight: 1.40kg
Note: The Receiver will stay linked/logged on to the Transmitter no matter DMX
signal or power is cut o. The log-in information is stored in an EEPROM and will not
be erased.
• This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,and (2) this device must accept any
interference received, including interference that may cause undesired operation.
• Changes or modications not expressly approved by the manufacturer responsible
for compliance could avoid the user’s authority to operate the equipment.

The WIRELESS DMX system is compact, lightweight and durable. Utilizing AFHSS - Adaptive
Frequency Hopping Spread Spectrum technology, the wireless system transmits or receives
safe and reliable DMX data without any delay and interference. Ideal for rental, mobile show,
event, club, DJ, etc. Please read this user manual carefully and thoroughly before
operation.
1.1 Unpacking
1.2 Safety Instructions
Carefully unpack the carton, check the contents to ensure that all parts are present,
and have been received in good condition. Contact your supplier immediately and
retain packing material for inspection if any part is missing or damaged.
1. INTRODUCTION
■1 x TRANSCEIVER WS or RECEIVER WS
■1 x Power cable
■1 x Mounting bracket
■1 x User Manual
!
Warning!!! To reduce the risk of re, electric shock, or injury to persons,
follow these important safety instructions:
The following items are included in the box:
1
▪This product is intended for indoor use only!
▪Please keep this User Guide for future consultation.
▪Do not attempt to dismantle and/or modify the transmitter in any way.
▪To prevent risk of re or shock, do not expose xture to rain or moisture.
▪Make sure that the voltage and frequency of power supply match the power
requirements of the transmitter/receiver.
▪Make sure power cord is never crimped or damaged.
▪The transmitter is only intended for installation, operation and maintenance by
qualied personnel.
1.3 Features
• Adaptive Frequency hopping technology - AFHSS
• Completely interference free
• Transmit 512 channels (1 universe) of DMX data
• Maximum 16 universes of DMX in one area
• One-button-go for quick setup
1) Power on the Receiver unit(s) and ensure that they are not linked with any other transmitter
(LINK indicators should be OFF).
2) Press and quickly release FUNCTION button on the Transmitter. The transmitter will scan for
all unlinked receivers for a period of 10 seconds - the LINK indicator on both the Transmitter
and Receiver(s) will ash rapidly.
3) If succefssful, the LINK indicator on Receiver(s) now go ON. If any failed, check that the
Receiver is in range and repeat procedure.
3.2 To add Receivers
Press and hold the Function button on the Receiver for about 3 seconds till the LINK indicator
go o. Now the Receiver is unlinked.
Note: You can add receivers at any time, even during operation. In an operational
system, logging on an additional receiver will make the logged-in units revert to
idle mode for 10 seconds; once the new units are logged-in they will all start again
together with the new unit.
3.3 To unlink a Receiver
4
Multipoint-to-multipoint
Up to 16 universes of DMX can be transmitted simultaneously using multipoint to
multipoint operation. All receivers in a multipoint system will listen only to the
designated transmitter without any delays or interference from other systems
working alongside.
RX
RX
RX
RX
TX
DMX
TX
DMX

1.4 Product overview
2. SETUP
2.1 Placing Transmitter and Receiver
2
For successful linking, the following conditions should be fullled:
2.2 Placing Transmitter and Receiver
The Wireless unit can be mounted onto truss with the mounting bracket (included).
a. Distance between Transmitter and Receiver should not exceed 200m.
b. Position of Transmitter and Receiver should be 1m at least above crowds and trees .
• Plug and play, no need conguration for IP address
• Point-to-point, point-to-multipoint or multpioint-to-multipoint operation
Function button DMX In/DMX OutOn/O Power In Fuse
500m max. in line of sight
1m min.
TRANSMITTER RECEIVER
TRANSMITTER RECEIVER
3. OPERATION INSTRUCTIONS
2.3 System connection
3
The wireless system is designed to work on AC 110V or 230V. Before applying power to a unit,
make sure that the unit’s input voltage matches the power source voltage.
Use DMX cables to connect DMX IN of the TRANSCEIVER to DMX source and DMX OUT of
RECEIVER to lighting equipments.
2.4 Power Adapter
3.1 3 types of operation
Point-to-multipoint
Point-to-point
RX
DMX
One Transmitter supports up to 512pcs Receivers in one point-to-muiltipint system.
RX
RX
TX
TX
DMX
Mounting bracket