Elite Screens ZCU1 User manual

080415-JA www.elitescreens.com 1
Universal Ceiling Trim Kit
Part numbers:
ZCU1, ZCU2, ZCU3, ZCU4, ZCU5
In-ceiling trim kit for Elite Electric Screens
User’s Guide

2
Hardware and Parts List
1. Assembly Plank
2. Brackets for VMAX 2 (below 135”)
Left x 1 pc
Right x 1pc
Left x 1 pc
Right x1 pc
3. Brackets for VMAX 2 (135”-170”)
4. Brackets for Home 2
Left x 1 pc
Right x 1pc
Left x 1 pc
Right x 1pc
5. Brackets for CineTension 2
6. Bracket/Plank for VMAX Tab-Tension Dual
Left x 1 pc
Right x 1pc
Bracket 4 pcs
Plank x 2 pcs
7. Connector x 2 pcs
8. Assembler x 4 pcs
9. Ceiling Panel x 4pcs
10. Suspension Bar x 4 pcs
(L: 910±10mm)
11. M6 Screw & Nut
x 12 pcs
12. M5 Screws x 26
pcs
13. M4 Screws x 8
pcs
14. M4 Screws x 8
pcs
15. M5 Nut x 10pcs
Installation
1. Use the correct bracket according to your screen series to install the screen.
VMAX2 Series (2)

3
VMAX 2 Series 135”-170 (3)
HOME2 Series (4)
CineTension2 Series (5)
VMAX Tab-Tension Dual Series (6)
2. Attach the Ceiling Panel (9) with the Connector (7).
Connector
Ceiling Panel
M5 Screws

4
3. Insert the Assembler (8) into to the groove of the Ceiling Panel (9)
4. Attach the Assembly Plank (1) to the Ceiling Panel (9) and secure with M4 screws (14) on
both sides as shown below.
Note: Step 5 only applies to a VMAX Tab-Tension Dual Series Installation.
5. Attach the VMAX Tab-Tension Dual Bracket (6) to the Assembler (8) and secure with the
M5 Screw and M5 Nut.
Assembly plank
M5 Screw
Bracket
M5Nut
Assembler
Assembly plank
Ceiling Panel
M4 Screws
Assembler
Assembly plank

5
ATTACH THE SCREEN TO THE TRIM KIT
1. Adjust the distance of the Assembler (8) to your screen as shown below and lightly
secure with the M6 Screw.
Note: Do not fix the M6 nut until attaching the Suspension Bar
M6 Screw
M5 Screw
M5 Screw
M6 Screw
VMAX 2 (below 135” & 135”-170”)
M6 Screw
M5Nut
Plank
Projection screen
VMAX Tab-Tension Dual
Series
M5 Screw
M6 Screw
Home2 Series
CineTension2 Series
Bracket

6
2. Adjust the level and secure the Assembler (8) with the M4 screws (13).
3. Cut the Suspension Bar (10) to your required length and install it on the bracket and
secure with the M6 nut (11).
4. Congratulations, the assembly is finished and your Screen and Universal Ceiling are
ready to beinstalled in the ceiling.
A. Example of CineTension 2 screen assembled
M4 Screw
M6 Screw
M6 Nut

7
B. Example of VMAX Tab-Tension Dual assembled
5. If your screen is the VMAX84H, VMAX100H, Home120H or Home150V, you can
assemble the Universal Ceiling kit without the Connector (7).
VMAX84H & VMAX100H Home120H & Home150V
For a local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Assembly Plank
Bracket
Suspension Bar
Bracket
Assembly Plank
Suspension Bar