Equiptec G20 Mobile User manual

:
G20 Mobile
Maintenance Platform
Owner’s Manual
www.equiptec.co

Contents
Introduction ................................................................
Compliance ................................................................
Assembly ....................................................................
Warranty ......................................................................
Safety Requirements ...............................................
Prior to Use ................................................................
Positioning the Girae G20 ...................................
G20 Use .....................................................................
Girae G20 Stability ................................................
Operation ...................................................................
Maintenance ..............................................................
Six Monthly Service Inspection ............................
Annual Service Inspection .....................................
Bi-Annual Service Inspection ................................
Girae G20 Parts Diagrams ...................................
Complete Unit Parts Diagram ...............................
Base Unit Parts Diagram ........................................
Roller Panel Parts Diagram ....................................
Hydraulic System ......................................................
Hydraulic Oil ..............................................................
Bleeding the Ram .....................................................
Descent Speed Adjustment ...................................
Hydraulic System Parts Identification ..................
1
1
1
2
2
2
2
3
4
5
6
7
8
9
10
10
11
12
13
13
13
14
15
Giraffe Owner’s ManualG20 - SB 1.0January 2022

Contents
Optional Accessories ...............................................
One Step Extension ..................................................
Two Step Extension ..................................................
Four Step Extension .................................................
Eight Step Extension ................................................
Hammerhead Deck ..................................................
Angle Deck .................................................................
Slide Out Deck ..........................................................
Trailer ...........................................................................
Transport .....................................................................
Notes ...........................................................................
Contact Details ..........................................................
16
16
16
16
16
17
17
17
17
18
19
20
Giraffe Owner’s Manual G20 - SB 1.0 January 2022

Your G20 is shipped in a consolidated form to facilitate cost efficient freight. Usually, the Assembly of the unit
can be performed by the local Distributor, but if it is more practical, or preferred by the client, it may be done
by the end user, provided there are competent personnel on site to perform the task. To assemble it ready for
use is about a 90 minute job for two Competent Personnel. Full instructions will come with the Unit for this
procedure and can also be found on Equiptec’s website at www.equiptec.co/instruction-manuals. Equiptec is
available to assist via video conference if required (during Business Hours, New Zealand time).
Note: It is a mandatory safety consideration that the G20 is assembled precisely, and if undertaking the
assembly procedure, it is the new Owner’s responsibility to ensure all appropriate Equiptec assembly
instruction resources are made fully available and are followed absolutely correctly. If there is any
doubt about any aspect, contact Equiptec for advice before proceeding further. It is also a mandatory
requirement to submit the required photos and details of the assembly via the warranty registration form
on the website, www.equiptec.co. This allows Equiptec staff to check the correct procedure has been
followed, and validate the commencement of the standard Warranty.
The Equiptec Giraffe G20 (G20) is designed to facilitate easy and simple stair access to a variable height
platform. It incorporates a large cantilever to allow the platform to be positioned over obstacles, and thus
provide a deck that is sturdy, and as ergonomically safe as possible to work from. The G20 has a wide variety
of Standard Accessories that can be added to it, and therefore can be Customised in different ways.
A copy of this manual should remain with the G20 at all times. Prior to using the Giraffe, the user should
familiarize his/herself fully with the contents, paying particular attention to the safety notes included as it is a
mandatory requirement that these are strictly followed.
To avoid confusion, Equiptec stipulates the official orientation of the G20 as follows:
• Front - is the direction you face as you climb the Stairs
• Rear (or Back) - is the opposite to the Front direction
• Left and Right are defined from looking forward i.e. as you would when you climb the stair
Regular maintenance as per the maintenance schedule in this manual is also a necessary requirement. Details
from these mandatory checks must be submitted to Equiptec via the service checklist form, this can be
accessed by scanning the ‘scan to service me’ QR code located on the stringer above the hydraulic pump or via
the link in the service reminder E-mail. The G20 comes with a 5 year Warranty which can be extended out to a
Lifetime Warranty provided every annual and biannual service is done in the due time, and a complete service
checklist form submitted to Equiptec.
Should the G20 ever be sold, hired out or handed over to any third party for any reason, it is required that a
copy of this manual should also be passed over at the same time to ensure the new owner and/or operator is
aware of the operational needs, constraints, safety points, and maintenance requirements of the G20 Platform.
Introduction
Giraffe Owner’s ManualG20 - SB 1.0Page 1 January 2022
The G20 units have been tested and confirmed to meet or exceed the strength, stability and all other applicable
requirements for the following standards:
• AS 1657 and AS/NZS 1576 (Australia and New Zealand)
• ANSI-ASC A14.7-2011 (USA)
• CSA Z11-12 (Canada)
Compliance
Assembly

Page 2Giraffe Owner’s Manual G20 - SB 1.0 January 2022
The standard Warranty for a G20 is 5 years. To ensure this warranty is in place, simply go to the Equiptec
website (www.equiptec.co) and complete the warranty registration form including the required photos of
the Assembly process as stated above. Equiptec will confirm the correct assembly has been achieved (or
contact you if they have any questions), that the Unit is registered for the 5 year warranty and it is good to
go! This 5 year warranty can be extended to a “Lifetime Warranty” by ensuring that every mandatory service
in this manual is performed correctly, at the correct time and that the required photos and information are
submitted to Equiptec via the service checklist form (either scan the QR code on the unit or click the link in the
reminder E-mail). Some situations a G20 could be used in are extremely demanding of the structure of any
machine. Consequently, it needs to be made clear that that the Term “Lifetime Warranty” means the period
that the Equipment could reasonably be expected to operate (in the circumstances it is operating in) without
fault in material or workmanship if used correctly for its intended purpose and maintained according to the
Manufacturers recommendations.
Warranty
Prior to Use
1. Check the G20 for any damage and/or missing
components, and that final site assembly has been
correctly completed. Proceed only when the unit is
in good and complete condition.
2. In addition to the “Hold Valve” (with the Black Plastic
knob on top) the Hydraulic raise/lower system on
the G20 is fitted with 2 safety valves. The first is
a “lock valve” (at the Base of the Cylinder) which
will lock the ram in case of any sudden loss of
pressure (hose, burst/cut etc.). The second one is
an adjustable restrictor valve to control the descent
speed of the platform. This is located adjacent to
(and on the right-hand side of) the Reservoir, and
should be checked and adjusted only if necessary, to
allow for a safe lowering speed of the working deck.
Refer to instructions to do this on page 14.
3. Warning: The user must check for all electrical
hazards (and contact all appropriate authorities if
necessary) in the area before positioning or using the
G20.
The G20 conducts electricity and offers no
electrical protection.
Positioning the G20
1. Check that the ground surface that the G20 is to
be used on is capable of supporting 75% of the
combined weight of the G20 and its intended load
(allow approximately 900kg (1980 lb.)) on any 2 of
the wheels.
2. The G20 is heavy. It is recommended that it is
moved by a minimum of 2 people.
3. Check that the course to be followed is free from
ground or overhead obstructions eg beams, trusses,
mezzanine floors, raised manholes, electrical cables,
gratings, potholes etc.
Safety Requirements

Positioning the G20
4. The standard issue castor wheels are not designed
to roll over obstacles. If the surface of the area the
G20 is to be moved across is soft, has larger stones,
objects or debris in the G20’s path, or for any reason
the G20 cannot be moved by manual pushing/
pulling, it is recommended to shift the G20 with
a forklift using the forklift pockets provided. The
G20 should not be towed or pushed by mechanical
means.
5. Under no circumstances must any personnel be
allowed on any part of the G20 whilst it is either
being moved, repositioned or adjusted for height.
6. Castor swivel directional locks are fitted to at least
one of the 2 front standard issue type castors. This
will greatly assist correct tracking, particularly if
being moved longer distances.
7. The G20 has “pinch points” or areas where crushing
could occur. Careful attention must be given to
keep clear of these areas. It is mandatory to keep
all limbs/heads clear of any part of the G20 that is
forward of the hydraulic pump handle, when the
G20 is being adjusted for height.
8. Always check that the deck will not collide with any
object as it is being raised or lowered. In particular,
ensure all personnel are well clear of the G20 when
raising or lowering the deck.
G20 Use
(general points - see also ‘Operation’)
1. Always ensure that all four castor brakes are
effective and locked on at all times (unless it is being
moved), especially before any personnel use the
G20.
2. Always respect the safe operating limits of the G20.
The design load is 300kg (660lb), including a point
load of 135kg (295lb), on the platform OR the stair
(not concurrently). The G20 has a large cantilever,
making this requirement absolutely essential.
Please note that in the case of the optional ‘angled
deck’ , ‘hammerhead deck ‘ or ‘slide out deck’
options being fitted, the safe operating limit is
reduced
.
3. It is forbidden to jump onto the G20 platform.
4. Temporary means of gaining additional height (eg
using a stepladder or trestle placed on top of the
working deck, or any surface) is strictly prohibited.
Safety Requirements
Giraffe Owner’s ManualG20 - SB 1.0Page 3 January 2022

Using the G20 (see also ‘Operation’)
5. In its standard configuration, the G20 deck has 3
access gates to facilitate access to/from a work
surface if required. These gates must remain shut
except when walking through them. Do not use
these gates if there is not a flat surface immediately
beyond it that has been certified to be of sufficient
strength to support your weight and has sufficient,
compliant guard railing in place. The gates must be
checked before use. They are spring loaded to shut
automatically. Do not use these gates if they do
not swing freely throughout their full rotation, and
automatically latch securely shut. These gates are
lockable, and it is recommended that they remain
shut and locked unless “walk through” access is
required.
6. The G20 is equipped with a Safety Rail at the top of
the stairs. This lifts into place and is lifted up and
back towards the user to disengage. Ensure this rail
is in place before proceeding with any work.
7. It is prohibited for personnel to be under the G20
work deck when it is loaded and/or elevated.
G20 Stability
1. If the ground surface is not within 5 degrees of level
do not use the G20. Reposition your work piece on
flat ground.
2. The G20 is not designed as a crane.
Do not use the
G20 to lift any loads, or as a platform to jack loads
off
.
3. The G20 will offer a large area to wind, and so care
needs to be taken when using it in windy conditions.
The table on page 5 gives a good indication of wind
conditions the G20 can and cannot be used in. Due
regard must be paid to certain circumstances where
wind conditions are magnified, eg in long open-
ended buildings, between buildings where the wind
may have a funneling effect, or where the G20 is
positioned close to the corner of a building. Never
attach tarpaulins or other coverings to the G20 as
this may seriously increase its susceptibility to wind
force.
Safety Requirements
Page 4Giraffe Owner’s Manual G20 - SB 1.0 January 2022

The G20 has a minimum operating temperature and
should not be used in an environment that is colder
than -20°c
.
The G20 is very simple to operate. In addition to
instructions given in the safety section of this
manual, the following gives a basic guide to what is
required.
1. Move the G20 as close as possible to the work piece
without adjusting the deck height. Being closer
allows you to more accurately gauge the height you
will require the deck to be.
2. When adjusting the height of the G20, follow this
sequence if moving the Platform UP.
Do not force the Pump handle if it is hard to pump.
Likewise, do not force the Ratchet Lock Lever if it is
hard to disengage.
Follow this sequence if adjusting the Platform
DOWN.
Note that the User must ensure the Ratchet Locks
are engaged on both sides before using the unit.
Safety Requirements
Wind
Description
Speed
Visable Indications Action Required
MPH KPH Metre /
Sec
Moderate
Breeze 13 - 18 20 - 29 5.5 - 7.9 Raises dust and loose paper
Safe to work on
G20
Fresh Breeze 19 - 24 30 - 38 8.0 - 10.7 Small trees in leaf
begin to sway
Cease to work
on the G20 and
secure all loose
items
Strong
Breeze 25 + 39 + 10.8 +
Large branches in
motion, difficult to
use umbrella,
telegraph wires whistle
Move G20 indoors
Giraffe Owner’s ManualG20 - SB 1.0Page 5 January 2022
G20 Stability
Operation

As with all machinery, particularly those used to support working personnel, a regular maintenance system is
required. In the case of the G20, the Manufacturer approved system is very simple, consisting of 6 Monthly,
Annual and Biannual service types.
The responsibility for ensuring these services are done rests with the Owner, however, in conjunction with
their Warranty, Equiptec offer a reminder service to help ensure these services are completed in the due
times. Mandatory services also need to be submitted to Equiptec via the service checklist form. This form is
accessed either by scanning the service QR code on the unit or via the link in the reminder E-mail. Completing
all mandatory Annual and Biannual Services, and submitting the required information to Equiptec will upgrade
the Warranty to a “Lifetime” Warranty of the Unit (provided that no mandatory services are missed, and of
course that there is no adverse damage etc). Equiptec may vet service reports and contact the Owner if they
see anything that looks like it needs attention.
While these checks are relatively simple, it is recommended that they are carried out by qualified tradespeople.
If the Owner does not wish to carry out any particular service or task themselves, Equiptec may be able to
arrange for an authorised Equiptec Distributor to visit the Site and perform these tasks, however, the Distributor
may charge for this service.
To assist in identifying Parts, refer to the Exploded Parts drawings on page 10.
Operation
Page 6Giraffe Owner’s Manual G20 - SB 1.0 January 2022
3. Move the G20 into the final position. Check it is
within 5 degrees of level and on a sufficiently firm
base surface.
4. Lock all 4 wheel-brakes
5. You may now climb the base stairs, unlatch the deck
Safety Rail, proceed on to the work deck and replace
the Safety Rail.
6. Once your work is finished, dismount and move the
Giraffe out to a clear area to allow the safe lowering
of the deck. See point 2 above on how to lower the
deck. Note that the restrictor valve described in
the safety section (under “Prior to Use”) should be
adjusted if the deck descends too fast or too slow.
Maintenance

Please note that it is essential that only genuine parts are used if any replacements are required.
Six Monthly Service Inspection
(scan the QR code to complete the service checklist form)
1. Conduct a thorough visual check for any damaged/bent components, or loose fastenings.
• Upload any photos of any damage
Note: Once photos of any damage are uploaded, check with Equiptec before continuing to operate a
damaged unit. It must be ascertained if the damage will compromise safety, strength, or the smooth
functioning of the G20.
2. Check all handrails are in place and firm. Ensure any components missing/loose are replaced/tightened (to
10 Nm / 7.5 ft/lbs).
3. Check the self-closing gates swing open and shut freely, automatically swing shut and lock, and that the lock
is effective. Adjust the Lock system if required. Instructions for the adjustment of the lock system can be
found at the manufacturers website www.ddtechglobal.com.
4. Check that the castor brake locks and directional locks are functioning correctly. Castor Brakes are
occasionally affected by high wear of the Tires. If this is the case, adjust the Brake system as per the
following instructions.
5. Check for any hydraulic leaks, that the hydraulic pump is functioning correctly, and is secure. If any issues
come to light, upload photos and contact Equiptec for advice.
6. Check all floating treads rise/nest correctly and do not catch on anything. Remove/repair any deformation
damage that may cause issues.
7. Check the Ratchet/Trigger system is functioning correctly. This will include checking the following elements.
• Trigger Cable Connections are all intact
• Trigger Cable Lever (by Hand Pump) operates effectively
Note: If issues are discovered, upload photos/description, and contact Equiptec for advice
Maintenance
Giraffe Owner’s ManualG20 - SB 1.0Page 7 January 2022
1. Loosen Lock Nut under Castor Brake release
lever
2. Adjust Grub Screw to alter brake tension
3. Re-tighten Lock Nut
Grub Screw
Lock Nut

Annual Service Inspection - Mandatory
(scan the QR code to complete the service checklist form)
1. Conduct a thorough clean both inside and out if necessary
2. Attend to all of the 6 Monthly checks plus...
3. Apply the brakes on the front wheels and jack the rear wheels slightly off the ground. Place packing block
under Chassis for safety. Check that the rear wheels spin easily (no roughness) and that the swivel turns
freely. Check the rear Castor mount bolts, and Castor Bracket mounting bolts, are tight (40 Nm / 30ft/lbs)
and secure before lowering the rear wheels and repeating the procedure for the front wheels. (Remember
to apply the brakes and chock the rear wheels and place a packing Block under the Chassis when jacking the
front ones.) If any issues are identified, contact Equiptec for advice.
4. Check all handrail and handrail post bolts are tightened to a maximum of 10 Nm (7.5 ft/lbs) and any Bolts
fitted to captive nuts are tightened to a maximum of 20 Nm (15 ft/lbs).
5. The G20 is not designed for use in corrosive situations. Check all fastenings and all surfaces for any signs of
corrosion. if any is found, photograph this and upload the photos to the service checklist form.
6. Check deck side member bolts (as highlighted in Diagram) are tightened to 40 Nm (30 ft/lbs).
7. Pump the machine to full height. Before lowering again, check:
• the Hydraulic Ram, fittings and hoses have no leaks, cracks or chafing. If any issues are identified,
upload photos and contact Equiptec for advice
• whether the Hydraulic Ram needs bleeding (usually causes a soft “spongey” lift that does not go to full
height easily). See Instructions in “Hydraulic System” section below
8. Check for any excess movement (either fore/aft or lateral) of the deck when fully elevated. Contact Equiptec
for advice if any issues come to light.
9. Check the Hydraulic Oil level by removing the breather on the top of the tank when the Ram is fully retracted
(
be careful not to allow any contamination of the oil ). The Oil level should be 60mm (2.36”) below the top
of the tank. Add more if necessary but be aware that overfilling will result in spillage via the Tank Breather
when the unit is coming down, and underfilling will result in the Ram not being able to reach full extension.
Note that as per the Hydraulic section below, the Oil should be changed at least every 2 years .
10. Check the unit has a smooth raise/lower action throughout its entire range. Adjust the descent speed if
required as per instructions in the “Hydraulic System” section below. If there are any further issues beyond
the descent control, contact Equiptec for advice.
Continued on next page
Maintenance
Page 8Giraffe Owner’s Manual G20 - SB 1.0 January 2022

Annual Service Inspection - Mandatory (continued)
11. As per service checklist form instructions upload photos to show the following details:
• Platform pivot bolts as shown
• Upper deck handrailing
• Upper deck gate(s) including rear safety rail
• Any damage that has been sustained by the unit and
• General views from the 4 elevations with the deck at full height
Biannual Service Inspection- Mandatory
(scan the QR code to complete the service checklist form)
1. All of the Annual Service checks plus...
2. Lift the G20 onto a solid and safe elevated support. Check thorougly for the following:
• Any damage, denting or any other structual issues around the Fork Pockets
• Check the Castor Bracket bolts under the Chassis are tight (40 Nm / 30 ft/lbs)
3. Place unit back on to floor. Raise the Deck to full height. Ensure the Ratchet Locks are locked in place
and proceed with a systematic check of all fastenings on the inside of the Base and Upper Units. Note the
following Torque Settings:
• Ram Mount bolts, Ratchet Trigger Guide Mounting bolts and the Roller Panel Bottom Strut bolts are all
tightened to a maximum of 20Nm (15 ft/lbs)
• Base Stair Mount bolts are tightened to a maximum of 10Nm (7.5 ft/lbs)
• Check that the Hydraulic Hoses and Ratchet Cables are tidily routed (away from moving Upper Unit
parts) and tied in place properly. Also check the Ram Hose connection is tight, with no leaks.
• Check the condition of all Rollers#
Note: Use a safe platform ladder such as an Equiptec Squirrel to access the Side Panel Top Covers and
remove them.
# Note: Check Roller condition carefully especially if the environment the G20 is operating in is
dusty or abrasive in any way. Should the Roller surfaces be roughened, they should be replaced. This
involves removing of the complete Upper Unit. Contact Equiptec for instructions on how to perform this
procedure
4. Lower the Deck to just above head height (with Ratchet Locks in place), and check the following:
• Ratchet Ladder rivet fastenings are firm
• All fittings and rivet fastenings under the Deck structure are tight (note that the M12 bolt at the Deck
Pivot Point is meant to remain loose – the only Bolt that may be so)
• Ram Top Mount bolt is firm (do not over tighten)
5. Pull up each Floating Tread and check:
• For any damage, dirt or debris, clean/remove as necessary
• All rivet fastenings are tight
• Rollers spin freely and evenly
6. Do a final run to check the Ratchet Locks function as they should
Remember to upload photos of any issues to the service checklist form
Please note that it is essential that only genuine parts are used if any replacements are required.
Maintenance
Giraffe Owner’s ManualG20 - SB 1.0Page 9 January 2022

Giraffe G20 Parts Diagrams
Complete Unit Parts Diagram
Maintenance
PROJECTION:
9
10
11
14
2
56 6 85
4
117
7
12
13 16
3
15
Item No. Part No. Accredo Description
1 GA A0002 GA Base Unit 1
2 GA A0004 GA Roller Panel Assembly 1
3 GA A0006 GA Upper Platform 1
4 GP0194 Floating Tread 5
5 GA WA0005L GA Wheel Bracket LH 2
6 GA WA0005R GA Wheel Bracket RH 2
7
GA A0008 Back Stair 1
8
- 300241 Castor 3
9
GA A0012 GA Handrail Assembly 1 2
10 GA A0013 GA Handrail Assembly 2 2
11 GA A0014 GA Handrail Assembly 3 2
12
GA A0015L GA Handrail Assembly 4(L) 1
13 GA A0015R GA Handrail Assembly 4(R) 1
14
GA A0016 GA Handrail Assembly 5 2
15 GA A0020 GA Left Post & Gate 1
16 GA A0021 GA Right Corner Post & Gates 1
17
Grab Handle 2
18
Directional Lock 1
19 - 300241 200mm Castor - VRS G 1
20 GA 0315 GA Rear Gate 1
A3
DO NOT SCALE FROM DRAWING
THE INFORMATION
CONTAINED IN THIS
DRAWING IS THE SOLE
PROPERTY OF EQUIPTEC ANY
REPRODUCTION IN PART OR
WHOLE WITHOUT THE
WRITTEN PERMISSION OF
EQUIPTEC IS PROHIBITED.
DESC.
DRAWN:
PART NO.
G20
13/11/2020
1:30
DIMENSIONS ARE IN MILLIMETERS
UNLESS OTHERWISE SPECIFIED
[phone]
www.equiptec.co
SCALE: SIZE
REV
EQUIPTEC
(C) Copyright
1 OF 2
SHEET
GENERAL NOTES
TOLERANCES
GENERAL
0 0.5
0.0 0.1
0.00 0.01
CUT & FOLDED
FOLD DIM 0.5
FOLD ANGLE 0.5
CUT PROFILE 0.1
PART INFO/NOTES:
BEND RADIUS & ALLOWANCES TO BE CHECKED BY 1.
MANUFACTURER AND PART MODIFIED TO SUIT AS PER FINISHED
DIMENSIONS.
ALL PARTS DEBURRED 2.
VISIBLE SIDE INDICATED BY A 3.
MATERIAL: Material <not specified>
A
ACCREDO NO.
USED ON MODELS:
No. Product
Code Description Qty No. Product Code Description Qty
1n/a G20 Base Unit Assembly 1 10 9840181 - 01 G20 Stair Mid Rail Assembly 2
2n/a G20 Roller Panel Assembly 1 11 9840182 - 01 G20 Platform Handrail Assembly 2
3n/a G20 Upper Platform Assembly 1 12 9840191 - 01 G20 Platform LH Handrail
Assembly 1
4 9840146 G20 Floating Tread 5 13 9840192 - 01 G20 Platform RH Handrail
Assembly 1
5 9840100 - 10 G20 Castor Bracket - LH 2 14 9840194 - 01 G20 Upper Platform Stair Handrail
Assembly 2
6 9840100 - 11 G20 Castor Bracket - RH 2 15 9840198 - 01 G20 Left Corner Post + Gate
Assembly 1
7n/a G20 Stair Assembly 1 16 9840199 - 01 G20 Right Corner Post + Gates
Assembly 1
8300241 200mm Castor - Giraffe 4 17 9840211 G20 Guide Handle 2
9 9840180 - 01 G20 Stair Handrail Assembly 2
Page 10Giraffe Owner’s Manual G20 - SB 1.0 January 2022

Giraffe Owner’s ManualG20 - SB 1.0Page 11 January 2022
Giraffe G20 Parts Diagrams
Base Unit Parts Diagram
Maintenance
PROJECTION:
16
13
12
2
4
81 1417
9
5
192520 3
7
6
10
1115 18 23
26
27
24
2122
Item No. Part No. Accredo Description
1 GA A0001 GA Chassis 1
2
GA 0007R 9840209 GA Front Side Panel RH 1
3
GA 0007L 9840208 GA Front Side Panel LH 1
4
GA 0008 9840212 GA Roller Mast 2
5
GA 0009 9840207 GA Front Panel 1
6
GA 0010R 9840211 GA Rear Side Panel RH 1
7
GA 0010L 9840210 GA Rear Side Panel LH 1
8
GA 0011R 9840214 GA Rear Mast RH 1
9
GA 0011L 9840213 GA Rear Mast LH 1
10
GA 0012 9840219 GA Top Fixed Tread 1
11
GA WA0003 9840220 GA Landing Rail 1
12
GA 0015 9840215 GA Mid Horizontal Strut 2
13
GA 0016 9840216 GA Top Horizontal Strut 2
14
GA 0017 9840285 GA Pump Moutn Bracket 1
15
GA 0031 9840231 GA Floating Tread Guide 10
16
GA 0032R GA Top Cover RH 1
17
5L Tank 1
18
GA 0056 9840217 GA Tube mount bracket 2
19
GA 0054 9840240 GA Ram 1
20
GA 0095 GA Front Panel Crush Tube 2
21
GA 0275
GA Landing Rail Cross
Member
1
22
GA0032L GA Top Cover LH 1
23
GA 0302
GA Front Panel Corner
Support
2
24
GA 0065 GA Pump Handle 1
25
GA A0051 GA Trigger Fully Assembly 2
26
GA A0052 GA Lever Assembly 1
27
GA 0066 9840239 GA Pump Handle Bracket 1
A3
DO NOT SCALE FROM DRAWING
THE INFORMATION
CONTAINED IN THIS
DRAWING IS THE SOLE
PROPERTY OF EQUIPTEC ANY
REPRODUCTION IN PART OR
WHOLE WITHOUT THE
WRITTEN PERMISSION OF
EQUIPTEC IS PROHIBITED.
DESC.
DRAWN:
PART NO.
GA Base Unit
13/11/2020
1:17
GA A0002
DIMENSIONS ARE IN MILLIMETERS
UNLESS OTHERWISE SPECIFIED
[phone]
www.equiptec.co
SCALE: SIZE
REV
EQUIPTEC
(C) Copyright
1 OF 1
SHEET
GENERAL NOTES
TOLERANCES
GENERAL
0 0.5
0.0 0.1
0.00 0.01
CUT & FOLDED
FOLD DIM 0.5
FOLD ANGLE 0.5
CUT PROFILE 0.1
PART INFO/NOTES:
BEND RADIUS & ALLOWANCES TO BE CHECKED BY 1.
MANUFACTURER AND PART MODIFIED TO SUIT AS PER FINISHED
DIMENSIONS.
ALL PARTS DEBURRED 2.
VISIBLE SIDE INDICATED BY A 3.
MATERIAL: Material <not specified>
B
ACCREDO NO.
USED ON MODELS:
No. Product
Code Description Qty No. Product Code Description Qty
1 9840101 - 01 G20 Chassis Assembly 1 15 9840143 G20 Floating Tread Guide 10
2 9840117 G20 Front Side Panel RH 1 16 9840163 G20 Top Cover RH 1
3 9840116 G20 Front Side Panel LH 1 17 9840111 - 01 G20 Hydraulic Tank 1
4 9840112 G20 Roller Mast 2 18 9840129 G20 Tube Mount Bracket 2
5 9840120 G20 Front Panel 1 19 9840110 G20 Ram 1
6 9840119 G20 Rear Side Panel RH 1 20 9840122 G20 Front Panel Crush Tube 2
7 9840118 G20 Rear Side Panel LH 1 21 9840142 G20 Landing Rail Cross Member 1
8 9840114 G20 Rear Mast RH 1 22 9840162 G20 Top Cover LH 1
9 9840113 G20 Rear Mast LH 1 23 9840121 G20 Front Panel Corner Support 2
10 9840126 G20 Top Fixed Tread 1 24 9840111 - 01 Hydraulic Pump Handle 1
11 9840141 G20 Landing Rail 1 25 9840155 - 01 G20 Trigger Wire Guide Assembly 2
12 9840127 G20 Mid Horizontal Strut 2 26 9840152 - 01 G20 Trigger Lever Assembly 1
13 9840128 G20 Top Horizontal Strut 2 27 9840109 - 01 G20 Trigger Wire Bracket Assembly 1
14 9840108 G20 Pump Mount Bracket 1 G20

Giraffe G20 Parts Diagrams
Roller Panel Parts Diagram
Maintenance
PROJECTION:
2
1
4
10
7
3
5
9
6
8
Item No. Part No. Accredo Description Qty.
1 GP0288R
Roller Panel RH 1
2 GP0288L
Roller Panel LH 1
3 GA 0022
9840229 Roller Panel Bottom Strut 2
4 GA WA0004
9840228 GA Roller Panel Upper Strut 1
5 GP0283
Side Support Roller 8
6 GA 0029
9840251 GA Nylon Mast Roller 8
7 GA 0030
9840232 GA Floating Tread Support 10
8 GA WA0019R
GA WA0019 Ratchet Ladder RH 1
9 GA 0062
9840249 GA Roller Bush 8
10 GA WA0019L
GA Ratchet Ladder LH 1
A3
DO NOT SCALE FROM DRAWING
THE INFORMATION
CONTAINED IN THIS
DRAWING IS THE SOLE
PROPERTY OF EQUIPTEC ANY
REPRODUCTION IN PART OR
WHOLE WITHOUT THE
WRITTEN PERMISSION OF
EQUIPTEC IS PROHIBITED.
DESC.
DRAWN:
PART NO.
GA Roller Panel Assembly
13/11/2020
1:12
GA A0004
DIMENSIONS ARE IN MILLIMETERS
UNLESS OTHERWISE SPECIFIED
[phone]
www.equiptec.co
SCALE: SIZE
REV
EQUIPTEC
(C) Copyright
1 OF 1
SHEET
GENERAL NOTES
TOLERANCES
GENERAL
0 0.5
0.0 0.1
0.00 0.01
CUT & FOLDED
FOLD DIM 0.5
FOLD ANGLE 0.5
CUT PROFILE 0.1
PART INFO/NOTES:
BEND RADIUS & ALLOWANCES TO BE CHECKED BY 1.
MANUFACTURER AND PART MODIFIED TO SUIT AS PER FINISHED
DIMENSIONS.
ALL PARTS DEBURRED 2.
VISIBLE SIDE INDICATED BY A 3.
MATERIAL: Material <not specified>
A
ACCREDO NO.
USED ON MODELS:
Page 12Giraffe Owner’s Manual G20 - SB 1.0 January 2022
No. Product
Code Description Qty No. Product Code Description Qty
1 9840132 - 01 G20 Roller Inner Panel Assembly
LH 1 6 9840115 AHP Nylon Mast Roller 8
2 9840133 - 01 G20 Roller Inner Panel Assembly
RH 1 7 9840144 G20 Floating Tread Support 10
3 9840137 G20 Roller Panel Bottom Strut 2 8 9840149 - 01 G20 Ratchet Ladder LH 1
4 9840136 G20 Roller Panel Upper Strut 1 9 9840175 AHP Roller Bush 8
5 9840140 G20 Side Support Roller Bracket 8 10 9840149 - 02 G20 Ratchet Ladder RH 1

Hydraulic System
Hydraulic Oil
The Oil used in the Giraffe hydraulic system is standard ISO 46 hydraulic oil. Brand equivalents are shown
here.
The recommended interval of change is 2 years. It may require changing sooner in certain circumstances.
Factors that would affect this include being used in a dusty environment or high humidity. Cracked seals or Oil
contamination will also necessitate an Oil change. NOTE that when changing the Oil, it is also recommended
to replace the Tank Breather fitting at the same time.
Bleeding the Ram
If the Ram movement becomes inconsistent, “spongey” or does not lift to the full height, it is likely that air has
got into the system and needs to be bled out. To bleed the Ram, follow these simple steps…
1. Pump the Ram up as high as it will go. Pump the handle slightly more to ensure the oil is under pressure.
2. Make sure the Platform is supported by engaged triggers, or some other external support system.
3. Move to the Front of the unit and locate the Bleed Valve that is near the top of the Ram, just above the
Landing rail “apron” as illustrated.
4. Have a rag ready to absorb any excess Oil. Place the rag under the Bleed Valve, covering the immediate
surrounding area, but leaving the Valve plug nut accessible.
5. Using a 19mm (3/4”) Spanner, “crack” open the nut very slowly. As you gradually unwind the nut, you should
hear air escaping, or may see frothy Oil coming out. There may also be some “spatters” of Oil/Air but keep
unwinding slowly till you see just Oil coming through.
6. Close the Valve nut immediately and tighten.
7. Check again to see if the Operation of the Ram has improved. If there is still some issues, repeat the
procedure till all air has been bled from the system, and the Ram is performing normally.
Maintenance
Giraffe Owner’s ManualG20 - SB 1.0Page 13 January 2022
Supplier Product Name Supplier Product Name
Atlantic Hy Lube Hydraulic Fluid ISO 46 Mobil DTE 25
BP Batran 46 Penrite Indus Pro Hydraulic 46
Caltex Rando HD 46 Prolube Hyplex 46
Castrol Hyspin H46 Shell Tellus 52 M 46, Tellus 52 MX 46
Fuchs Renolin B Plus 46 Total Azolla ZS 46
Gulf Western Superdraulic 46 Valvoline Ultramax 46
Hitec Hydraulic 46

Page 14Giraffe Owner’s Manual G20 - SB 1.0 January 2022
Hydraulic System
Descent Speed Adjustment
The Hydraulic system has a valve to control the speed of the descent of the Platform. This will be factory set
at a suitable speed that is both practical and safe. This should not need any alteration, but if for any reason
further adjustment is required, the procedure is as follows…
1. Pump the Ram up to full height.
2. Make sure the Platform is supported by engaged triggers, or some other external support system.
3. Unlock the small Allen Key Grub Screw in the side of the Valve Knob.
4. Wind this Valve completely shut (as far as it will go in the clockwise direction).
5. Activate the Trigger Rods by pushing the Lever against the Rear Panel as shown.
6. Release the Main Hold valve as you would to lower the Ram. The Ram should not move if the Speed
Control Valve is completely shut.
7. Slowly open the Speed Control Valve and the deck will start to come down. The further you open the Speed
Control Valve, the faster the deck will lower.
8. When the desired speed is reached, shut of the Main Hold Valve, and lock the Speed Control Valve position
using the small Allen Key Grub Screw in the side of the Valve Knob.
Maintenance

Giraffe Owner’s ManualG20 - SB 1.0Page 15 January 2022
Hydraulic System
Hydraulic System Parts Identification
The system is relatively simple. See hydraulic system general assembly below.
Maintenance
8
3
14
3
8
12
1
13
2
4
3356
10
9
7
11 3
ITEM NO. DESCRIPTION PART NO. Default/QTY.
1 PM 25 s PUMP 1
2
1/4"-3/8" ADAPTOR AC-0406 1
3
DOWTY WASHER 1/4" DO4 2002600 5
4
1/4" FLOW CONTROL VALVE WITH CHECK VRFU9001 1
5
1/4"-1/4" ADAPTOR BB-0404 1
6
HOSE HH-ETECH 1
7
1/2" VELOCITY FUSE 9009480 1
8
1/4" BUNG B-04 2
9
DOWTY WASHER 1/2" DO8 2002602 1
10 1/4"-1/2" ADAPTOR BB-0408 1
11 1/4" BREATHER 2002646 1
12 Handle 1
13 5L Tank 5L Tank 1
14 G20 Ram GA 0054 1

Page 16Giraffe Owner’s Manual G20 - SB 1.0 January 2022
Many optional extras are available for the G20. They can all be retrofitted relatively simply, but Equiptec
recommend these tasks are undertaken by an Engineering based Tradesperson. The instructions for fitting
each type are all downloadable from the Equiptec website, and Equiptec remains available to assist via Video
Conference if required. If in doubt, do not hesitate to contact Equiptec for advice.
Fitting/Operation instructions for optional equipment is supplied with the said equipment.
Options available include...
One Step Extension
Taller Single Step height castor brackets paired with
additional Single Step module on the base stair give
the standard G20 a single step (225mm) addition to
all platform heights.
Two Step Extension
As per the One Step Extension, taller Double Step height
castor brackets paired with additional Double Step module
on the base stair gives the standard G20 a double step
(450mm) addition to all platform heights.
Four Step Sub Chassis
A full sub chassis giving the standard G20 a four-step
(900mm) addition to all platform heights.
Eight Step Sub Chassis
A full sub chassis, including a landing (to meet the AS/NZS
standards requirements) give the standard G20 an eight-step
(1800mm) addition to all platform heights.
Optional Accessories

Hammerhead Deck
This option gives a wider deck at the front. With 1.8m of
room it allows 2 people to comfortably work alongside
each other. The Hammerhead Deck also offers the ability
to remove gates on either, or both sides, giving unimpeded
access to a 1.8m wide workface. Note that the load capacity
of the whole G20 is reduced to 200kg (440lb) when this
unit is installed
Angled Deck
Turns at right angles to the main deck, allowing the user
to reach 1m out over obstacles while the G20 is parallel
to that object. The same pack can be utilized on either
left or right hand side. Note that the load capacity of
the whole G20 is reduced to 150kg (330lb) when this
unit is installed.
Slide Out Deck
This option gives an extra 1.4m of cantilever, resulting in a
total of 2.9m cantilever reach. Note that the load capacity of
the whole G20 is reduced to 150kg (330lb) when this unit is
installed.
Options coming soon...
Trailer
A trailer system is another option that will allow your fully built G20 to be quickly and easily loaded and firmly
locked in place or unlocked and unloaded so it can continue to be used on its own wheels. When mounted
on this purpose built (and very tough) trailer, the G20 can be towed over all various terrain by a vehicle such
as a ute or pick up to whatever site it is required to be at. Using the trailer mounted jacks and flip down trailer
steps means that your G20 can remain mounted on the trailer, be backed up to the job and used for even the
toughest field maintenance situation.
Optional Accessories
Giraffe Owner’s ManualG20 - SB 1.0Page 17 January 2022