EZIROBOT E1800S User manual

Please read this manual carefully before usePlease keep this manual for future referenceROHSUSER MANUAL

CONTENTS 1. INTRODUCTION AND SAFETY 12. PRESENTATION 33. INSTALLATION 64. CONTROL PANEL 106. APP USER MANUAL125. USE 117. MAINTENANCE AND STORAGE 168.TROUBLE SHOOTING 179. EXPLODED VIEW 19

The products are manufactured by Zhejiang Tianchen Intelligence&Technology Co., Ltd.www.exgain-tech.comThank you for purchasing our product. You will have and enjoy the extra free time while using our robot lawn mower to mow your lawn. You will be impressed with your lawn's appearance and best of
IMPORTANT! Robot lawn mower can be dangerous if incorrectly used!WARNINGThe following pages contain important safety and
Carefully read and reviewinstructions in this manual.
all safety instructions, warnings and cautions contained in this manual.Failure to read and follow these instructions, warnings and cautions statements may result in severe injury or death to persons and pets or damage to personal all, Tianchen robot makes it for you.1. INTRODUCTION AND SAFETY1. INTRODUCTION AND SAFETY
1.1 Introduction
TThe robot mower may be used only by those who knowhow to operate it after reading and understanding theinstructions in this manual.Model: E1800CE, RoHs approved.operating instructions. Please read and follow all property. It’s not permitted to modify the original design Product, product specifications and this document aresubject to change without notice. All other trademarksare property of their respective owners.1. INTRODUCTION AND SAFETY1. INTRODUCTION AND SAFETY1. INTRODUCTION AND SAFETYIMPORTANT INFORMATIONRead through the Operators Manualcarefully and understand the content beforeusing your Robot.1.2 Symbols on MowerThese symbols can be found in the mower. Study themcarefully so you understand their significance.
1. The symbol is pasted on the top cover, Please read the means carefully before use the appliance.
1. WARNING-this is a dangerous power tool. Use care when operating and follow all safety instructions and warnings.2. Read the owners/operating manual carefully and follow all safety instructions before operating the machine.3. Objects can be thrown from mower while operating, keep a safe distance from the machine when operating, take caution.4. Keep children, pets and bystanders away from mower when operating.5. WARNING-Operate the disabling device before working on or lifting the machine.6. Never use a high-pressure washer or even running water to clean the mower.7. Sharp rotating blades. Keep hands and feet away and do not attempt to lift mower from this area.8. WARNING-Do not ride on the machine. 2. Specifications symbolPasted on mowerPasted on charging station: Waste electrical products should not be disposed
waste. Please recycle where of as household
Authority or facilities exist. Check with your Local Taizhou Tianchen Intelligence &Electrics Co,Ltd Product name: Robot lawn mower Model: XXXXX IPX4Input: XXX V --- 2A 85W
20XX
Made in China
S.N.:XXXXXXXXXXX
RoHSS.N.: XXXX XX XX XXXyearmonthdatenumberProduct name: Robot lawn mower Model: E1800 Ip54Input: 29.4 V 4A 85W
Made in China ROHS S.N.:XXXXXXXXXXX Product name: Robot lawn mower Model: E1800 Ip54Input: 29.4 V 4AOuput 29.4 4A
:VMade in China ROHS Zhejiang Tianchen Intelligence&Technology Co., Ltd. retailer for recycling advice.of robot. All modifications are made at your own risk. 120546789- 1 -Zhejiang Tianchen Intelligence&Technology Co., Ltd.

1. INTRODUCTION AND SAFETYThis label is pasted on chargingstation, please make sure to position this side towards lawn interior. Failureto do may result in damage to property or persons.DANGER! Sharp rotating blade. Keep hands and feet
injury can away. Serious
4. Charging station symbol.5. Warning symbol. occur.1.3 Symbols in the User ManualThese symbols can be found in this user manual.A warning box indicates a risk of personal injury exist. An information box indicates a risk of material damageexist, especially when the stated instructions are not followed. The box is also used where there is a risk of WARNINGxxxxxxxxxxxxxxxxxxxxxxxxx.IMPORTANT INFORMATIONxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx.user error. 1.4 Safety instructions- Read the owners/operation manual carefully and
and warning instructions.follow all the safety - This machine has sharp rotation blades! Never allow
operate unattended; keep bystanders, the mower to
mower when in operation.children and pets away from
- Never allow anyone to ride or sit on mower.- Never allow anyone or person who is not familiar with
of the mower to operate the mower.the safe operation - Keep hands and feet away from the cutting blades and parts.other moving - Never attempt to service or adjust the mower while it - Inspect and clear the mowing area of all debris (toys,
items of clothing, anything with a height tree branches,
mower.less than 6cm) before operating the - Never raise the mower or attempt to inspect the
is operating.blades while the mower - Always turn off the power before lifting the mower or
adjustment.attempting any - When operating the mower in manual mode, maintain wear proper foot apparel.- Do not operate the mower on slopes greater than 30 a firm footing is not possible. device is damaged or inoperable. - Do not attempt to disable or defeat any safety feature is in operation.
from behind or around the mower and a safe distance
manual operation on slopes wheredegrees or use it in
- Do not operate the mower if any safety feature or or device.- Use heavy gloves when inspecting or servicing the - Wear eye protection and use gloves when installing
driving the wire stakes/pegs. Firmly the virtual wire and
wire from becomingdrive all pegs in order to keep the - Do not use the charging station power supply with an
- Use only the original equipment power pack and power
with this mower. supply/charger - Do not use the power supply/charger if the cord has- Do not place metal objects in the area of the charging
charging station. sheets on the- Do not place metal objects across the charging heads- Do no spray water directly into the docking area of the
or onto the control panel on charging charging station - The mower has sharp rotating blades! Please care the
mowing, in case of serious injury occur.mower when it is
- Keep the lawn mower in perfect operating conditions
maintenance procedures outlined by performing the
maintenance by the manufacturer. Good guarantees better performance and longer service life.- In order not to irreversibly damage electric and
wash the robot with water jetselectronic parts, do not
partially or at a high pressure and do not plunge it - It is absolutely forbidden to use the robot in explosive
environments. and flammable - The operator or user is responsible for accidents or
other people or their property.hazards occurring to blades. a tripping hazard. extension cord. become damaged. of the mower. station. thoroughly in water, as it is not watertight.
- Fill up all small holes and even all small mounds inside
working area. It’s to keep the robot with perfect operating.
CAUTION!Position this side of the Charging Stationtowards lawn interior.
DANGER
- 2 -

2. PRESENTATION2. PRESENTATIONThis chapter contains information you should be aware of before placing the installation.1Emergency button Press it to turn on the mower.2Control panel345Cutting height adjustment knob6Charging sheetPower button7Home buttonPress it when the mower is on,it goes back to charging stationautomatically.8Virtual wire light9Charging lightRed: chargingGreen: full charged / idle.Consumable parts:1. Blades2. Virtual wire3. Virtual wire connectors4. Pegs5. Stakes52.1 What’s in box 12346Blade- 3 -6. Rear running wheels7. Front wheels1389711101215161920222118Colorless: in good connectingRed: Broken wire/ idle1011Power terminal12Virtual wire terminal13Hole for stake14Charger15Virtual wire (100m):Used to mark mowing area and create a virtual wall for the mower.16Virtual wire connectors (10pcs):Used to connect virtual wire.17Pegs (100pcs):Used to fix the virtual wire to the ground around the lawn perimeterand around obstacles.19Stakes (4pcs):Used to fix the charging station to the ground.18Blades for replacement (3pcs)English user manualCharging head20211417red terminalblack terminalPress it to turn off the mower.Charging headCutting height adjustment spanner228.Cutting height adjustment
spanner

2. PRESENTATION2.2 Function of E1800- Lift sensor There are lift sensors located between the top and middle- Tilt sensor There are tilt sensors installed on the mower too, when
mower is tilted over 30 degrees in any direction, it the
seconds.stops working within 2 - Bump sensorThe whole top cover is movable. Both front and side of mower equipped with bump sensors that will
activate when the mower strikes solid, fixed object when
that object is at least 6cm in vertical height from the
supporting surface of the mower. When the bump sensor
- Rain sensor There are two rain sensors located on the
mower. The mower will go back
to the charging station
when it's raining.automatically Turn on: the mower will go back home if it is raining. Turn off: the mower will go on mowing when it is raining.- Wificover. If the mower is lifted from ground, it will stops working within 1 second. activated, the mower will back up for working.
Rain sensors can be selected ON/OFF from APP.
- Area working time setting(mowing schedule)- Touch sensor Set up one week (From Monday to Sunday, once for
schedule from APP. This function each day) cutting - Cutting width: 21cm- Easy cutting height adjustments The cutting height could be adjusted on the mower .- Auto recharge system When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is complete, the mower will back up a few centimeters ready to go again in stand by mode. - Emergency stop switch There is an emergency button located on the top of
color. mower and in red
should be used together with Area location setting. - Two cutting modes There are two cutting modes of the mower, go straight
efficiency). and go circle (high In Auto, mower selects cutting mode intelligently. It goes straight if the grass is sparse or it has be cut off,
long.and it goes circle if the grass is dense or
In manual mode, the mower will go where you direct it.
-
use 100m-600m of virtual wire). The wire. (we suggest to
station, the virtualmower will follow virtual wire to charging
on the virtual wire wire acts as a virtual fence. It will get
wire and starts cutting inside.- Mower stops working if virtual wire is cut off or
power off.charging station is If virtual wire is cut or broken, or the charging station
loose power, the mower will stop working within 3 seconds
- Four steps to safely start the mower- Overload protect
The cutting motor and running motor are monitored
continuously during operation for any situation that
may cause these motors to over-load.
In the event this is detected, the mower stops operating.
- Waterproof Waterproof design, there is an inner cover under top
inside parts from humidity. cover which protect Virtual wire
The robot lawn mower can't be operated without a virtual
- GyroscopeThe mower has gyroscope to keep it going straight on
until it meets charging sheets, then it gets off from virtual
The waterproof class is I - Area location setting(Subarea setting)
You can select Subareas for the mower to cut. This works
well for large lawn. See Section 6.4. - Different languages selection on App.- 4 -P54.
Connect charging station with power supply by charger and make sure the recharging light is in green color. 2. Connect virtual wire to charging station and make sure it is in good connecting(virtual wire light in colorless). 3. Turn on the power button
- Range
There are four range options, user can choose the
distance when robot hit virtual wire according the condition of different lawns.1. The Android user search “EGROBOT” in the Google Store to download the application.The IOS user can search “EGROBOT” in the Apple inclines. Play to download the application. Press it to turn on the mower.Press it again to turn off the mower.Touch the handle when the mower is cutting, it willcease function. bottom cover cutting height adjustment knob via the equipped spanner.
4. Press emergency button and start auto mode.

2. PRESENTATION2.3 Technical data
E1800E1800SModel No.
Coverage(for once charging)
500m ±20％1500m ±20％200m ±20％1000m ±20％Working capacity52*39*27cm(LWH)17KGS14KGSMower sizeGross weightNet weight85W≤60db3pcs2.5-5.5cm21cm18cm35m/min3000rpm
30degree Max slope
40℃Qty for cutting bladesBlades rotate speed
Max ambient functioning temp.
Rated powerNoiseCutting heightCutting widthCutting speedHill capabilityMower technical date
Note:How large an area is mow per recharged depends primarily on the condition of the blade and the type of grass, growth rate and humidity. The shape of garden is also significant. If the garden mainly consists of open lawns, mower can mow more area per hour than if the garden consists of several small lawns separated by
600m/0.5mm100m/0.5mm
Virtual wire maximum length
Standard virtual wire length
44*48.2*15cm(LWH)Charging station size
Charging station and virtual wire
2.4 Working routeFollow virtual wire walking is optionalCutting height adjustmentRain sensorAuto rechargeIntelligent spiralingGo straightAnti theftLift sensorTilt sensorWIFI ApplicationBump sensorWaterproofTouch sensorTime set-up systemEmergency switchPassword set-upGyroscopeAverage working timeType of batteryBattery capacityCharging timeMower is disabled if virtual wire is cut or broken
Mower is disabled without power to charging station
trees, flower beds and passages.Language option
≤2hours4.4AhLithium
Subarea settingRange optionBatteryFunctions:- 5 -2222
E1800T700m ±20％1800m ±20％
22
6.6Ah≤hours33-4hours2-3hours2.2Ah≤1.5hours45mins

3. INSTALLATIONThis chapter describes how you to install this mower. Before starting the installation, read the previous Read the whole of this chapter before starting the installation. How the installation is made also affects how well the mower will work. It is therefore important3.1 PreparationsTraining- Read the instructions carefully. Be familiar with the
proper use of the mower.controls and the
- Never allow people unfamiliar with these instructions
the mower. Local regulations or children to use - The operator or user is responsible for accidents or
to other people or their property.hazards occurring 3.2 Hardware adjustmentsBlade adjustment The mowing system used by this mower is based on an effective and energy efficient principle. Unlike normal lawn mowers, the mower cuts the grass instead
Rain sensors on the mower is optional,suggest operate the
mower in dry weather to obtain best possible result.
Even though the mower can mow in rain,wet grass collects on mower easily and the risk of slippingon steep slopes increases.The blades must be in good condition to obtain the best mowing result. In order to keep the blade sharp for as long as possible it is important to keep the lawn free from branches, small stones and other objects 3. INSTALLATIONchapter 2. Presentation.
the installation carefully. to plan may restrict the age of the operator.
of striking it off.(especially the objects less than 6cm height). Please fill
up small holes and even out small mounds to make sure
lawn is flat. How to adjust the cutting height:Cutting height explanation: take 3cm level for example.3.3 Charging station installation- Choose best installation place, please make sure
no magnetic interference and no it is flat, no water,
station. obstacle in the front of charging - Please fix the charging station on horizontal place andCharging station best install place:1. Make sure it is flat2. No magnetic interference3. No water and far away from puddle
4. No obstacle in front of charging station
- Lay virtual wire- Fix the charging stakes by IMPORTANT INFORMATIONBefore locate the charging station, please make sure mower must follow the virtual wire and back to station in CLOCKWISE direction. as picture shows. station with fourIMPORTANT INFORMATIONDo not tread or walk on the charging station plate.
3CM
Grass Height
Cutting height: 3cm
- 6 -3cmPeghammer.1. Turn power off3. Adjust cutting height device manually 2.5cm-5.5cm.2. Use height adjustment spanner rotate knob clockwise.4. . Use tool rotate knob anticlockwise correct direction.Cutting height adjustment knob

3. INSTALLATION3.4 Virtual wire installationThe virtual wire can be installed in one of the following- Securing the wire to the ground with pegs. It is preferable to staple down the virtual wire, if you
adjustments to the virtual wire during want to make - Bury the wire It is preferable to bury the virtual wire(max depth: 5cm)
the lawn. if you want to detach or aerate If necessary both methods can be combined so one
wire is stapled down and thepart of the virtual - Install virtual wire with pegs 1 meter apart. It’s best to use smooth radius corners than sharp - Bury virtual wire below grass and fasten it on
that the mower shouldthe ground with pegs, so not cut the wire. virtual wireAdd pegs in order to pull thevirtual wire down to the ground surface, below the grass tips.OKIMPORTANT INFORMATIONHard or dry ground may cause pegs to break when driving them in. In extreme cases, watering the lawnways: the first few weeks of operation. remainder is buried. where the pegs will be driven.- A minimum distances between the front of the charging station and an And make sure the obstacle is 2 meters.
least distance from corner to front of charging station is at 2.5 meters. Make sure to lay a 2.5 meters minimum >9010cmPoolMax:1cm
Passage or a ground with same level of the lawn.
Min:40cmMin:40CMMin:40CMStraight-lineat least:2.5mHouse, wall, fence or other obstacle higher than the lawn- If a high obstacle, for example a house, wall, fence or other obstacle which is higher than the cutting lawn
prevent mower at least 40cm from the obstacle. This will Location
virtual wire in front of charging station.straight-light of
the virtual wire should be laid borders the working area,
with the obstacle.from colliding
- If a passage or a ground with same height of cutting lawn,
the virtual wire should be laid at least 10cm from the edge. - A minimum distance between the pool edge of virtual wire is 40cm.- A maximum distance of the virtual wireto and from the island is 1cm, and fix the - There are two types of set up of the virtual wire around the charging station. Put the charging station near corner. please take location for reference. Please make sure to set a straight-line at least of 2.5m in front of charging station. The charging station should be far away from puddle. - 7 -two wires with one peg.
. See pictures.angles- A minimum distance between two corners is 1meter.

3. INSTALLATION
- Use the virtual wire to isolate areas inside the working
islands around obstacles that can area by creating
flower beds andnot withstand a collision, for example, fountains. Run the wire out to the area, route it
pegs are used, the wire should be the same route. If
return route. When laid under the same peg on the
the virtual wire to and from the island with a maximum
- If protected obstacles are grouped closely together isolate them individually. Continuous virtual island if obstacles are close to edge, leave them out of the mowing area. Virtual wireMax: 1cmMax: 1cmVirtual wireMax: 1cm 40cmMin: 2m around the area to be isolated and then back along distance of 1cm, the mower can drive over the wire. - The distance between charging station and virtualloop should be 2 meters at least. - Joining the virtual wire . If the virtual wire is not long enough and needs to be spliced: Use supplied wire connector. It is waterproof and gives a reliable electrical connection. To splice: Insert both cable ends in the connector. Now press down the button on top of the connector fully. Use a pair of pliers or the like, as the button on the connector is difficult to press down by hand. - Care must be taken not to create a corner sharper
degrees when setting up virtual wire. shorter than 90
degrees can cause the A corner sharper less than 90 mower to lose track of virtual wire. We can make Correct corner set up,using several angle toavoid an angle of lessthan 90°.Greater than 2mProper setup in sharp cornersIncorrect corner setup greater than 90 degrees corner like follow picture shows.- 8-Virtual wire connectingGreaterthan 2mTree with hole or flowers around require placing a wire around it1cm

3. INSTALLATION3.6 Virtual wire and charging station connecting.
2. Connect the cut two ends of virtual wire to virtual wire
terminal located on charging station.
WARNING
Redundant virtual wire at back of charging station
must be cut off.
1. Cut the two ends of virtual
wire to a length of 1cm that’s
convenient for reaching the virtual wire terminal oncharging station.Strip the two ends of wire.3.7 Power connection. 1212-++-Power terminal on charging station Power terminal on charger
1. Connect charger terminal with charging station powerb
terminal . a2. Connect the charger with power supply.3.The virtual wire light turns colorless while virtual wireconnected well with charging station.A failed connecting between virtual wire and chargingstation cause a blinking red light and send out a beeping from charging station.3.Charging light on station in green: Non-recharging.charging light on station in red: recharging.3.8 Recharge. 1. 2. IMPORTANT INFORMATIONAll the buttons (except the emergency switch and power button ) are locked which can not be used during the robot is in recharging.- 9 - Connect 1 from plug a to 1 from plug b and screw it it tightly.3.5 Charging head installation. Please fasten the charging heads on the chargingstation in clockwise.Pls take care of positive and negative terminal.The mower will go back
to the charging station
when it's raining.automatically Turn on: the mower will go back home if it is raining. Turn off: the mower will go on mowing when it is raining.
Rain sensors can be selected ON/OFF from APP.
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is complete, the mower will back up a few centimeters and stand by. 3. The mower reverses several centimeters and stop there with entering standby mode after fully recharged.

When the mower stops with alarm, the alarm indicator light will keeps flickering, cancel alarm by press confirm button , alarm indicator light will be off.Note: If the mower stopped frequently, please check alarm messages which showed on the APP. Turn on the emergency switch, when the signal light flickers to bright, press home button , indicator light starts flickering, press confirm button , indicator light off, mower enter into home mode.Note: If the signal light keeps flickering all the time, need to rematch the address between mower and charging station.-Turn on the emergency switch, when the signal light flickers to bright, press auto button , indicator light start flickering, press confirm button , indicator light off, mower enter into the auto mode.
4. CONTROL PANEL 4.1Control Panel view4. CONTROL PANEL - 10 -
Take mower close to charging station, turn on the emergency switch,press auto button and home button simultaneously, the signal light starts flickering, press the home button on the charging station, the signal light turns bright,press confirm button on the mower panel until the signal light is off, the matching complete, turn off the mower and started again.Mower was matched with charging station before leave the factory.- Note: AAAA Auto mode Home buttonPower light(lighted when power is on)Signal lightAlarm light(flickering when mower alarms)Confirm button(to confirm your selection)4.5Match mower with charging station:4.2AUTO MODE(lighted when mower detect signal from charging station)4.3HOME MODE4.4Mower alarming

5. Use5. USEIMPORTANT INFORMATION- Do not leave the mower to operate unattended if you
are pets, children or people in the know that there - Mow only in daylight or in good artificial light.- Avoid operating the mower in wet grass.- Do not operate the mower when barefoot or wearing - Always wear substantial footwear and long trousers.- Always be sure of your footing on slopes.- Use extreme caution when reversing the mower - Always switch on the mower according to instructions
away from the blade. with feet well 5.1 Preparation- Ensure the correct installation of the virtual wire. - Periodically inspect the area where the mower
and remove all stones, sticks, wires, is to be used
objects especially the heightbones, and other foreign
- Periodically visually inspect that the blades, blade
cutter assembly are not worn or damaged. bolts and Read the safety instructions before you startKeep your hands and feet away from the rotating blade. Never put your hands or feet close to or under the body when the motorsWARNINGWARNING vicinity
open sandals. towards you.your mower.are running. of objects is less than 6cm.
Replace worn or damaged blades and bolts in sets to
- Connect the two ends of virtual wire to the terminal on charging virtual wire is in goodstation, and ensure
colorless). connecting. (Light on charging station is in - Insert charger into charging station and secure it with
charger to power threaded cap. And then connect
connectionsupply. Ensure the charging station has a good
5.2 Starting the mower preserve balance.IMPORTANT INFORMATION
charging station is Green. and the light on - Periodically inspect the lawn is without any small hole or mound.
User can not start the mower if virtual wire or
charging station is not in good connection. There are two locations of start the mower.1.Take the mower clockwise onto virtual wire, make surethat the mower is not connected with two charging
sheets on charging station. Otherwise, the mower is in
recharging Mode, it can not be started. 2.Take the robot to start point. 5.3 Stopping mower /Turning off mower1. Press stop button from APP. Mower stops and enters standby mode. 2. The mower can be turned off by pressing the Emergency button directly.3. Press power button under to turn off.
the mower5.4 Emergency Switch
Press Emergency button at any time the mower power
off at once. User has to restart it. If set If set
off, the robot begins cutting inside mowing Edge EEddggee mmoowwiinngg lawn directly. - 11 -on, the robot will follow the virtual wire cutting for one circle, and back to station first. Turn on the Power button under the mower.To start the robot.2.Press the Emergency button
to turn on the robot.
3. Select AUTO mode, the mower starts working.1.
If the mower lost contact with station, AUTO or Note: HOME mode is not able to start.The signal light
A
is always flickering,then need rematch the mower with charging station,pls refer to 4.5Match mower with charging station.

The APP is available for IOS and Andriod phone.Download and Install：The Android user pls search “EGROBOT” in Google Play to download. .The IOS user pls search “EGROBOT” in the Apple Store to download.For and turn on the mower according to the user manual.Then enter the smart phone setting interface--WI-FI to connect the device.Pls note for first time it takes about 3-5minutes to connect device, and the device can only connect with one phoneat the same time.the first time please connect the charging station and virtual wire The using of the App:Click the APP you installed and enter it.6.APP USER MANUAL- 12 -

6.1 Remote control function- 13 -6.APP USER MANUAL1.Press ”Auto”, the mower will work automatically.2.Press “Remote”, the mower with indication.Pls note in Remote mode, robot does not recognize the 3. Press “Home”, the robot will go back to station automatically..4 .Press “Stop” can stop the robot and Pls note this does not work when mower is charging.5.The blades could be turned on or off by pressstand by. “MOW” .6.2 Function settings1. There are 13 languages will work in manual and user could direct the mower to work wire and station.for option: English/French/German/Danish/Swedish/Finnish/Norwegian/Italian/Spanish/Russian/Polish/Dutch/Chinese.2.Range function:there are four range options, user can choose the distance when mower hit virtual wire accordingthe condition of different lawns.3.For the functions like rain sensor,touch sensor,audio alarm ON: mower goes back to charging station when it is raining.OFF: mower goes on working when it is raining.are optional.Rain sensor:After finish setting function,pls press Send to save thesettings.6.3 Date&Week&Time settings1.You can synchronize the mower time to cellphone time.press Send to save thesettings.2.After setting new time, pls6.4 Working Area Setting1.This function is to increasethe mowing efficiency for large area.It allows to separate a large area intomaximum 6 small areas.2.Area location setting 2.1 before entering into this interface, pls separate the garden into several areas as per your own demand. Take separate 3areas for example below:
1234

- 14 -6.APP USER MANUAL 2-1Area 1 is non-optional,selects by default. 2-2After select Area, the symbol* will be in red color.2-3 Start locating to set memory point.A memory point is to program thewhere to leave virtual wire and go inner lawn.Each area needsa memory point.Pls make sure the mower voltagemore than 27V before setting thememory points,and pls put the mower at charging station before locating.-It is best to set the memory pointin the middle of two corners.--A better position of memory point is 3meter distancefrom the beginning or the end of an area.-Route the wire around the passage to separate the the area.The virtual wire to and from the edge of passage is 1meter at least.pls refer to below picture.-A minimum distance between the virtual wire which is to make passage is 50cm. 2.2 choose the areas that you set accordingly:3.Area working-time setting 3.1.The Area working-time setting should be used together with Area location setting. 3.2.Choose the mower working day per week. 3.3Set the start time, then set the working time for each area and Send. -Pls note if the working areas are for example 3areas,do not set the time for other unselected areas. -If set Area 1 with 0min, it means Non-cutting in Area 1. -If unselect working in Area 2,even has set working time in Area 3, mower will not work in Area 3. 3.4.Edge mowing: ON:every time mower will cross to the back of station to mow the edge grass on virtual wire and follow the wire back to station first. 4.Put the mower back to station and wait for working.

- 15 -6.APP USER MANUAL1.This is for setting the and you can set 4-digit6.5 Password mower password.2. password. Initial password:1234. Input old password,then Input new password and Send.3.Password function is optional.6.6 Mower-state Query1.You can get the mowervoltage info.2.Click “Mower-state Query”to view alarm info.

6. MAINTENANCE AND STORAGE7. To remove the deposits and/or other residues from
suitable brush.the blade, use a 8. Clean the outside of the charging station from any
residues.accumulated 9. Keep all nuts, bolts and screws tight to be sure the
safe working condition. appliance is in 10. Replace worn or damaged parts for safety.11. Ensure that only replacement cutting means of the
used. right type are
12. Ensure that batteries are charged by using the correct
recommended by the manufacturer. charger 13.Incorrect use may result in electric shock,
of corrosive liquid from the overheating or leakage 14. In the event leakage of electrolyte flush with 5.Do not wash the inside parts of the robot and do not use water jets in pressure so not to damage6.Check the lower part of the robot (cutting blade area
and remove the deposits and/or residues and wheels)
correct functioning of the robot. that might obstruct the WARNINGNever use a high-pressure washer oreven running water to clean the robot.6. MAINTENANCE AND STORAGE- During maintenance operations, use the individual
by the Manufacturer , especiallyprotections indicated - Before performing maintenance operations, make
has stopped in safety conditions.sure that the robot PROGRAMMED MAINTENANCE INTERVALS CHARTSee “Robotcleaning”See “Bladereplacement”RobotCarry out cleaningSee “Robotcleaning”6.1 Robot cleaning 1.Stop the robot in safety conditions.
2. Wear protective gloves.FrequencyComponentType of operationReferenceEvery weekEvery monthBladeClean and check theefficiency of the bladeIf the blade is bent dueto an impact or if it isworn-out, replace it.3.Clean all the outside surfaces of the
warm water.robot with a sponge soaked in
4.Do not use solvents or benzene so not to damage
surfaces and the plastic components.the varnished Every months 3RobotCarry out for rechageSee “Battery” when intervening on the blade. the electric and the electronic components.battery.
agent, seek medical help if it comeswater/neutralising
etc. into contact with the eyes 15. Servicing of the mower should be according
manufacturers instructions. This product to
must be disposed of at a (include battery pack)
and designated collection pint for electrical
city office or the shop where you your local electronic waste. For more information, contact purchased the product.6.2 Robot StoragePacked the mower and all spareparts with the original package, and storage the carton off the ground in a 6.3 Blade replacementBlade replace steps: 1.Stop the robot in safe conditions. 2. Wear protective gloves. 3. Turn the Robot upside down. 4. Unscrew the blade and remove it. 5. Replace a new blade and screw it tightly.cool, dry place. Temperature should not be colder than 14F°(-10℃) IMPORTANT INFORMATIONCharge the battery fully at the end of the season before winter storage. And recharge it every 3 months.- 16 -6.5 Battery6.4 Front wheel cleaningThe battery is maintenance-free, but has a limited lifeWhen front wheels are not easy to rotate, please turn robot upside down, check it and dismantle the screw cap to take the front wheel out of robot, dismantle end caps and remove the residues, like mud, grass etc from end cap, then reinstall it on the robot. span of 1-3years. Battery life is dependent on the length of the using season and how many hours per of use per week, means that the battery must be week the robot is used. A long season or many hours replaced more regularly.- Attentions of lithium batteries Please charge the lithium batteries in accordance with
procedures.standard time and When the power is too low. It should be started
possible. charging as soon as Storage, we suggest the optimum storage of lithium
power and keep in the shade.battery is with 80% - Disused battery processing Please contact the nearest waste treatment center
recycling and proper disposal and consultation with of views. Don’t take apart, repair or modify the battery privately. Don’t connect the anode and cathode of battery.

7.TROUBLE SHOOTINGAuto mode is not able to beeping. 1.main power is shut off.Bad communication between charging station and mower. 1. Check the power and make sure the charger is connecting well with power supply and charging station. 1.The virtual wire fails to send signals. 2.The virtual wire was cut off.1.Check the virtual wire light on charging station.
wire is Be sure the virtual connected to the charging station well (light in 2. Connect the virtual wire with wire connectors. 7. TROUBLE SHOOTINGProblemAlert infoSolutionsPossible reasonscolorless). Mower stops working and beeps. 1. Mower is lifted from ground. 2. Someone or object ride or sit on the mower. 1. Take the mower to level ground and restart it. 2. Take the object away from mower and restart it. Mower stops working and beeps. 1. Running wheel strike
1. Cutting height is too low.
2. Blade strikes hard objects.
3. Mower is trapped in lawn1. Adjust the cutting heightto suitable height.
2. Clean the lawn and make
sure it is free from hard objects.
3. Clean the lawn where mower
is trapped or restart the mower
in another place.
Mower stops working and beeps. hard objects. 2. The mower is trapped in lawn.
1. Clean the lawn and make
sure it is free from hard objects.
2. Clean the lawn where mower
is trapped or restart the mower
in another place.
- 17 -Virtual wire was cut off.Charging station is out of start,charging station is Signal light is off.power.Auto mode is not able to beeping. start,charging station is Signal light is off.Lift sensor or pressure sensoractivated.Current of right running motor is too large,check it.Current of left running motor is too large,check it.Current of cutting motor is too large,check it.

7.TROUBLE SHOOTINGMower is tilted over than 30 degrees from the ground.
Turn off the mower and take
the mower to level ground. Then restart the mower. ProblemDisplaySolutionsPossible reasonsMower stops working and beeps. 2.Battery lifetime1. Check whether charger is well connected.
2. Send the mower to service
station and replace the battery.The batteries can not recharge1. Grass is extremelyovergrown or very wet, 2. Terrain needs landscaping repairs.
1. Cut the grass appropriateheight.
2. Fill in all holes, cover orexclude all exposed roots in order to smooth theterrain.Obstacle along the path.
Mower does not complete
Watch the full operation of follow virtual wire walking and confirm no obstacle is present. the edge.Mower does not detect the charging station contacts. The ground before the charging station isn’t flat. Reset the charging station in a flat place.Confirm the ground before
the charging station is leveled
with the station if necessary
fill area with dirt and level off.
Relocate the virtual wire. 1. Replace a new blade.
2. Stop the mower in safety,
use protection gloves to
avoid the risk of cuts on
hands, remove the fold cause from blade.
3. Start the robot in new place.
1. Damaged cutting blade. 2. Cutting blade flooded by
residues(tapes, ropes, plastic
fragments, etc)
3.The start of mower occurred
with obstacles being too
closed (less than 1m away)
or in presence of unexpected
obstacles (fallen branches, forgotten objects, etc.)The mower is very noisy. Height difference between the
charging station and
lawn surface at the
entrance to charging station.
Virtual wire incorrectly placed
Mower reaches charging
station when its contacts are above the charging
The mower behaves in an
anomalous around flower
beds.sheets.
4. Damaged running motor 5. Grass too high.
4. Get the motor repair or replace by service station. 5. Increase the cutting heightor use a normal lawn mower.
- 18 -
or cutting motor.
decreases.1.Charger is not poweredon.Mower gets stuck,does not move.Robot is over tilted.