FASANO TOOLS FGA 332 User manual

AIR DRILL
KEYLESS (1-10
The reproduction of this document (even in partial form) is prohibited without the Fasangas S.r.l. authorization
Rev.
122017
FGA 332

1
GENERAL WARNINGS
2
TECHNICAL FEATURES OF THE TOOL
3
IMPORTANT SAFETY INSTRUCTIONS
4
INSTRUCTIONS FOR THE USE OF THE TOOL
5
MAINTENANCE
6
TROUBLESHOOTING
7
DISPOSAL INFORMATIONS
8
EC DECLARATION OF CONFORMITY
9
WARRANTY
CONTENT

Before to use the tool, please read carefully the instruction contained in this manu
al.Improper or unsafe
use of this tool can result in death or serious bodily injury.
This manual of instructions constitutes an integral part of product and it has to be edited by the end user for every
possible future consultation. It contains important informations about the safety use of the product.
Use destination
.
This tool and its accessories, must only be used for the purpose for which they have been conceived. A different
use from that one suitable could cause damages to people, animals or th
wrong and unreasonable uses, as,for example, the un-observance of the safety instruction, the use of no origina
l
accessories and operation not authorized on the product.
Model: FGA 332
Type: AIR DRILL
Weight: 0,9 kg (2.0 lb)
Compressed air:
Max. pressure for use: 6.2 bar (90 psi)
Air consumption: 4 CFM (113 l/min)
Keyless chuck: 1-10 mm
Free speed at 6.2 BAR: 1800 rpm
Min. hose size: (10 mm)
Noise values in according to EN ISO 15744:
A-weighted sound pressure level (Lpf): 86 dB
A-weighted sound power level (LW): 91 dB
Peak C-weighted sound pressure level <97 dB
Measurement uncertainty (Standard): 3 dB
Vibration value in according to EN ISO 28927-5:
Vibration value: 0.8 m/s2
Measurement uncertainty: 0.1 m/s2
1.
GENERAL WARNINGS
FGA 332 AIR DRILL
2. TECHNICAL FEATURES OF THE TOOLS

When using this air tool, the following basic safety precautions should always be followed to reduce the risk to
personal injury:
Always wear safety glasses with side shields in accordance with applicable regulations.
Air powered equipment are capable of propelling materials such as metal chips, saw dust and other debris at
high speed, which could result in serious eye injury. Tool attachments can become loose or break and
fly apart
propelling particles at the operator. Compressed air can be hazardous. The air stream can cause injury to soft
Always wear hearing protection in accordance with applicable regulations.
Long term exposure to noise produced from the operation of air tools can lead to permanent hearing loss.
Always wear protective gloves in accordance with applicable regulations.
Always protect the airway du
ring use.
When using the tool are generated abrasive dust and debris that can be harmful to the lungs and respiratory
system in general. Some materials (for example: adhesives, tar, etc.) contain chemical substances whose
vapours can produce serious injuries to the respiratory tract in case of prolonged exposure.
Avoid prolonged and continuous use of the tool.
Prolonged exposure to tool vibrations can cause severe neurological and circulatory disorders.
Never exceed the maximum pressure rating of th
e tool. The maximum pressure rating of the tool is
reported in the technical specifications (Paragraph 2 of this user manual) and on the same tool.
Exceeding the MAX. pressure rating of tool could cause an explosion resulting in serious injury.
- Never o
- Work in a clean, well ventilated area free of combustible materials.
- Never use oxygen, carbon dioxide or other bottled gases as a power source for air tool.
WARNINGS
- Never carry the tool by the hose. Always hold the tool only from the the ergonomic handle it is endowed
- Never wear loose fitting clothes, or apparel, which contains loose straps or ties, etc. which could become
entangled in moving parts
of the tool. Remove any jewelry, watches, identifications, bracelets, necklaces, etc.
which might become caught by the tool.
- Remove air hose when tool is not in use and store tool in secure location away in particular from reach of
children.
- Before removing the compressed air supply hose from the tool, make sure to have previously closed the tap
supply compressed air coming from the supply
- Remove air hose to lubricate or add attachments and accessories to the tool.
- Never operate tool while under the influence of drugs or alcohol.
-
- Keep handles dry, clean and free from oil and grease.
- Do not use accessories designed for use without a manual as locking systems.
- Make sure that any attachments are securely assembled before to use the tool.
- Do not remove the labels placed on the tool.
3. IMPORTANT SAF
ETY INSTRUCTIONS
FGA 332 AIR DRILL

Before each use:
ATTENTION
Before proceeding with the operation of lubrication, detachment / attachment, adjustment or
installation of accessories, disconnect the air supply hose from the tool, having first taken care to
close the tap of compressed air supply
1)
ATTENTION
Always use clean, dry air at 90 PSI (6.2 bars) maximum air pressure. Dust, corrosive fumes and/or
excessive moisture can ruin the internal components of a pneumatic tool.
2) Lubricate the
3) Install the accessories (drill bits) verifying its integrity and that they are securely housed.
USE:
1. Turn air compressor on and allow air tank to fill.
2. 90 PSI (6.2 bars). This tool operates at a maximum 90 PSI (6.2 bar) pressure.
3. Loosen the collect by twisting the chuck, then insert the selected drill bit. Tighten the collect again by twisting the chuck with
reverse direction.
4. Connect the tool to air hose of recommended size (see the Technical specifications paragraph of this user manual).
IMPORTANT: The use of air filters and air line lubricators is recommended
5. Position the drill bit at the point to be drilledand depress the trigger.
ROTATING DIRECTION:
o The clockwise rotation is obtained by rotating the forward/reverse lever placed near the trigger of the tool
towards the F position.
o The counterclockwise rotation is obtained by rotating the forward/reverse lever placed near the trigger of the
tool towards the R position.
6. Depress the trigger placed on the tool handle to operate tool.
7. If the drill bit penetrates the work piece, keep the tool running makes it easier to remove this tool from work piece.
8. Release the trigger to stop the tool.
9. When job is completed, turn off the air compressor and store the air tool after lubrication.
WARNINGS
- Use the tool only in conjunction with accessories (bits) that have a secure attachment during
operation.
- Use the tool only with accessories (bits) that are appropriate to the type of material to be drilled
(wood, metal, plastic, concrete, etc...)
- Check the integrity of the locking devices (chuck) before using the tool..
ATTENTION
Keep all nuts, bolts and screws tight and ensure equipment is in safe working conditions.
ATTENTION
Do not use damaged, frayed or deteriorated air hoses and fitting
WARNING
- Before start operating this tool, make sure the rotating direction.
- Do not change the tool direction of rotation while it is running.
4. INSTRUCTIONS FOR USE OF THE TOOL
FGA 332 AIR DRILL

LUBRIFICATION
Air tools require regular lubrication throughout the life of the tool. The air motor and bearing use compressed air to power
the tool. Because moisture in compressed air will rust the air motor, you must lubricate the motor daily. An inline oiler is
recommended.
To lubricate the air motor manually:
Disconnect the tool from the air supply holding it so the air inlet faces up.
Depress the trigger and place one to two drops of air tool oil in the air inlet
Connect the tool to an air source, cover the exhaust end with a towe
l and run for a few
seconds.
Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.
If the tool does not start:
make sure that in the compressed air circuit there is really pressure;
check that all the valves are opened;
check all the connections of the air supply;
check if the safety valves are actived;
if the problem persists, the tool need to be repaired from qualified personell.
When the tool is not usable and not repairable, dispose it according to regulations of the place in order to safeguard the environment.
This product complies with the dispositions of the following European Directives and Harmonized Standards:
2006/42/EC
Machinery direcive
EN ISO 12100:2010
EN ISO 11148-3:2012
EN ISO 15744:2008
EN ISO 28927-5:2015
ATTENTION
ALWAYS DISCONNECT AIR SUPPLY BEFORE LUBRICATING, INSTALLING, REMOVING OR
ADJUSTING THE TOOL.
ATTENTION
Any excess oil in the motor is immediately expelled from the exhaust port. Always direct exhaust port away
from people or objects.
WARNING
ALWAYS DISCONNECT AIR SUPPLY BEFORE PERFORMING ANY WORK ON THE TOOL.
FGA 332 AIR DRILL
5. MAINTENANCE
6. TROUBLESHOOTING
7. DISPOSAL INFORMATIONS
8. EC DECLARATION OF CONFORMITY

This tool is warranted to be free from defects in materials and workmanship (for a normal use of service) for a period
of one year.
Any instrument found detective within one year from the delivery date and returned to the factory with transportation
charges prepaid, will be repaired, adjusted, or replaced at no charge to the original purchaser.
es or fuses.
If the defect has been caused by a misuse or abnormal operating conditions, the repair will be billed to the customer at
a nominal cost.
FGA 332 AIR DRILL
9. WARRANTY