Feelgood mr. steam AirButler Instruction manual

Installation, Operation & Maintenance Manual
AirButler/AirButler2
AirButlerX/Linear
mr
.steam® Feel Good Inc.
Rev 5.2022
Table of Contents:
AirTempo Wireless Control
AromaSteam SteamHead
Linear Steamhead
SteamLinx Mobile App
MS/Super AutoFlush
MX Autoflush
Condensation Pan
PUR100474
PUR100421
PUR103936
PUR100518
PUR100200E
PUR100532
TS0012
1-11pg
12-13pg
14-24pg
26-27pg
18-30pg
31-33pg
34-35pg

Installation, Operation & Maintenance Manual
AirTempo
Wireless Touch Control with Steamhead
mr
.steam® Feel Good Inc.
PUR100474 Rev 5.22
®

2
®Installation, Operating & Maintenance Instructions
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
SAVE THESE INSTRUCTIONS
2. Do not permit children under the age of 16 to
use this steambath.
3. Steam is hot and can cause injury or death if improperly
used. Steam rooms contain steam and elevated temperatures. Please read and
observe all warnings in this manual before installing or using a steam room.
4. To reduce the risk of injury:
A. The wet surfaces of steam enclosures may be slippery. Use care when
entering or leaving.
B. The steam head is hot. Do not touch the steamhead and avoid the steam
near the steamhead.
C.Prolonged use of the steam system can raise excessively the internal human
body temperature and impair the body’s ability to regulate its internal
temperature (hyperthermia). Limit your use of steam to 10-15 minutes until
you are certain of your body’s reaction.
D. Excessive temperatures have a high potential for causing fetal damage
during the early months of pregnancy. Pregnant or possibly pregnant
women should consult a physician regarding correct exposure.
E. Obese persons and persons with a history of heart disease, low or high
blood pressure, circulatory system problems, or diabetes should consult a
physician before using a steambath.
F. Persons using medication should consult a physician before using a
steambath since some medication may induce drowsiness while other
medications may affect heart rate, blood pressure and circulation.
HYPERTHERMIA occurs when the internal temperature of the body reaches a
level several degrees above the normal body temperature of 98.6° F. The
symptoms of hyperthermia include an increase in the internal temperature of the
body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath; and
f) Unconsciousness.
The use of alcohol, drugs, or medication can greatly
increase the risk of hyperthermia.
READ ME FIRST!
Table of Contents:
As you follow these instructions, you will notice
warning and caution symbols. This blocked information is important
for the safe and efficient installation and operation of the
steambath system. These are types of potential hazards that may
occur during installation and operation:
Indicates a potentially hazardous situation, which
could result in death or serious injury.
Indicates a potentially hazardous situation, which
may result in minor or moderate injury or product damage.
This highlights information that is especially relevant to
a problem-free installation.
All information in these instructions is based on the latest product
information available at the time of publication. MrSteam reserves
the right to make changes at any time without notice.
Important Safety Instructions . . . . . . . . . . . . . . .2
Before Installing . . . . . . . . . . . . . . . . . . . . . . . . .4
Dimensional Information . . . . . . . . . . . . . . . . . .5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Surface Mount & Glass Mount . . . . . . . . . . . .6-7
Wireless Receiver . . . . . . . . . . . . . . . . . . . . . .7-8
Remote Temperature Probe . . . . . . . . . . . . .9-11
AirTempo Operating Instructions . . . . . . . .12-14
Battery Replacement . . . . . . . . . . . . . . . . . . . .15
System Status Codes. . . . . . . . . . . . . . . . . . . . .16
Pairing, Care & Maintenance, Warranty. . . . . . .16
Conformity & Compliances . . . . . . . . . . . . . . .17
FCC Statements . . . . . . . . . . . . . . . . . . . . . . . .18
Parts List & Technical Specs . . . . . . . . . . . . . . .19
Flush Mount Installation . . . . . . . . . . . . . . .20-21
Flush Mount Template . . . . . . . . . . . . . . . . . . .22

3
®Installation Instructions
Installation Instructions
3/4”
3-5/8”
3-5/8”
1-5/8”
4-7/8”
7/8”
Dimensional Information for the AirTempo
BOX CONTENTS:
U À/i«ÊÌÀ
U iVÀ>ÌÛiÊ/À
U >LiÊÎÊvÌ°®
U 7ÀiiÃÃÊ,iViÛiÀ
U >ÌÌiÀiÃÊÓ®
U ÕÌ}Ê-VÀiÜÃÊÓ®
U -Ìi>i>`
U /ÕLiÊvÊ-ViÊ-i>>Ì
U -ÕÀv>ViÊÕÌÊ>ÞiÌ
U "ÜiÀ½ÃÊ>Õ>
Drawings for illustrative purposes only 
Wireless ReceiverAirTempo
(shown with decorative trim)
Installation Instructions for AirTempo
STEP 2
The AirTempoÊVÌÀÊV>ÊLiÊÃÕÀv>ViÊÀÊyÕÃÊ
mounted according to personal preference.
Flush mount components are sold separately
(104232RD & 104232SQ). Contact a MrSteam
Ài«ÀiÃiÌ>ÌÛiÊvÊ>ÊyÕÃÊÕÌÊÌÊÃÊii`i`]Ê
see page 22.
Surface Mount AirTempo
U ,iÛiÊÌiÊÃÕÀv>ViÊÕÌÊL>ÞiÌÊvÀ
the back of the AirTempo Control.
U ,iÛiÊEÊ`ÃV>À`ÊÌiÊÀii>ÃiÊ«>«iÀÊÌ
expose the adhesive liner.
U ÃÕÀiÊÌiÊÕÌ}ÊÃÕÀv>ViÊÃÊVi>ÊEÊ`ÀÞ°
U *>ViÊÌiÊL>ÞiÌÊÊÌiÊÜ>ÊÊÌiÊ`iÃÀi`ÊV>Ì°
U 7>ÌÊ£xÊÕÌiÃÊLivÀiÊ«>V}ÊÌiÊVÌÀÊÊÌiÊL>ÞiÌÊÌ
ensure the adhesive is secured
IMPORTANT 7UGVJGUETGY CPFCPEJQTRTQXKFGFVQUGEWTG
VJGDC[QPGVVQVJGYCNNCUTGSWKTGFHQTTQWIJQTWPGXGPYCNN
UWTHCEGU6JGUWTHCEGOQWPVDC[QPGVUWRRQTVUVJGYGKIJVQH
VJG#KT6GORQEQPVTQN
STEP 1
Determine the desired installation location of the control. The AirTempo
controls are designed to be installed inside or outside the steam room
as a matter of personal preference. If the control is installed outside the
steam room a Remote Temperature Probe part number MSTS must be
installed inside the steam room.
IMPORTAN See installation instructions for the MSTS Temperature
Probe (pgs.10-12) before rough-in or installation of control.
If the control is installed inside the steam room the control must be located:
• 4-5 feet above the floor near the bather seating area.
• On a vertical wall
• Mounting surface should be clean and dry
The control features an integral temperature sensor. Locate the control
in a location representative of the desired steam bathing temperatures.
Do not locate the control above or near the steam head or direct steam
emissions. Locating the controls near the steamhead or near direct
steam emissions may result in poor steam room temperature control.
DO NOT mount on grout/caulk lines.
The control can be located up to 60 feet from the wireless receiver.
Construction materials affect the communication between the control
and receiver. Test the range of the AirTempo. It may be necessary to
change the location of the wireless receiver to improve the range.
Contact MrSteam technical service for an optional 30 or 60 foot cable.
STEP 2

4
®Installation Instruction
Installation Instruction
Wireless Receiver Installation
The control can be located up to 60 feet from the
wireless receiver. Construction materials may affect
the communication between the control and the
receiver. Test the range of the AirTempo. It may
be necessary to change the location of the wireless
receiver to improve the range. Contact MrSteam
technical service for an optional 30 or 60 foot cable.
Using the 3 foot cable provided, plug one end into
the steam bath generator and the other end into the
AirTempo.
Attach the dongle on a wall adjacent to the steam
generator using the screw provided.
Steam
Generator
Wireless
Receiver
Mounting on Glass
When installing AirTempo on glass a peel and stick film is provided on pages
20-21 and may be used as a mask for a clean look from behind the glass.
Steam
Generator
3 ft. Cable Standard
(optional 30’ or 60’
cable available)
Wireless Receiver
AirTempo Control
Surface or Flush Mount
Steam Head
All drawings for illustrative purposes only.
IMPORTAN Do not rest the dongle on the
steam generator, the metal case of the
generator may shield the RF signal.
IMPORTAN The control features an integral
temperature sensor. Locate the control in a
location representative of the desired steam
bathing temperatures. DO NOT locate the
control above or near the steam head or direct
steam emissions.
To avoid
unintentional steambath
operation, do not locate the
control where other controls,
accessories, shower heads,
valves, body sprays or similar
within the shower could cause
confusion or interfere with the
MrSteam control’s intended use
and function.

5
®Installation, Operating & Maintenance Instructions
Installation Instruction
The Remote Temperature Probe is required when the
AirTempo control is installed outside the steam room. Failure to install the
probe, or failure to install the probe correctly will result in an inoperable
control and result in excessive temperatures and a hazardous condition.
The Remote Temperature Probe is for use with AirTempo,
iTempo and iTempoPlus controls only. Do not use with any other controls.
Do not use any other temperature probe with the AirTempo, iTempo and
iTempoPlus controls. Noncompatible products may result in an inoperative
control and a hazardous condition.
Install the AirTempo controls according to the installation
instructions on pages 6-7. Failure to do so may result in an inoperative
control and a hazardous condition.
 Determine the location of the Remote Temperature Probe:
The Remote Temperature Probe must be installed:
C On a vertical surface
D {xÊviiÌÊ>LÛiÊÌiÊv À
E in a location representative of the desired steam bathing
temperature.V>Ì}Ìi-/-i>ÀÌiÃÌi>i>`Ài>À`ÀiVÌ
ÃÌi>iÃÃÃ>ÞÀiÃÕÌ«ÀÃÌi>ÀÌi«iÀ>ÌÕÀiVÌÀ°
d. The probe has an integral 30’ cable. Insure that the probe and/or
steam generator are located accordingly. Ƃ-/-ÜÌÌi}À>
ÈävÌV>LiÃ>Ã>Û>>Li-/-Èä®°
2. Drill a 5/16 inch diameter hole in the wall.
Do not oversize or under size the hole. Clean area thoroughly.
NOTE: The silicone supplied by MrSteam can be used to meet a va-
riety of sealing and gasketing. It cures to silicone rubber and adheres
to glass, wood, metal, porcelain, ceramic tile, painted surfaces, many
plastics and rubber. Surfaces must be clean and dry. Apply thin layer
of product. Fit together and support if necessary. Allow excess mate-
rial to cure, then trim with a sharp blade. Sealant “skins” in 5 minutes,
dries to touch in 1 hour. Fully cures and bonds in 24 hrs.
3. Remove the knock-out from the steam generator jacket as shown in
Diagram 1.
4. Insert the probe cable through the knock-out and connect to the
connector on the steam generator printed circuit board marked EXT
TEMP as shown in Diagram 1.
CAUTION
!
CAUTION
!
CAUTION
!
Installing the Remote Temperature Probe (PN: MSTS)
Mr.Steam Steam Generator
(shown with cover removed
and NOT installed)
Temperature
Probe Cable
(30 feet)
Knock-Out
Temperature
Sensor Probe
Temperature
Probe Connection
DIAGRAM 1
Drawings for Illustrative Purposes Only.

6
®Installation Instruction
Installation Instruction
Silicone Sealant
Cable
Wall
1⁄4" minimum
1⁄2" maximum
Sectional View
STEAM ROOM
INTERIOR
Diagram 2
Installed Remote Temperature Probe
showing a minimum of 1/4” of the probe
exposed to steam room air
Diagram 
5. Route the end of the probe cable with the temperature probe
through the wall into the steam room as shown in Diagram 2.
IMPORTAN DO NOT strain, staple, pinch or otherwise damage
the probe cable.
6. With a minimal length of the cable exposed apply silicone
(provided) to the hole in the wall as required to create a mois-
ture seal as shown in Diagram 2.
7. Push the temperature cable and probe into hole as required to
leave minimum 1/4”, maximum 1/2” of the bulb exposed as
shown in Diagram 3.
W ARNING Insure a minimum of 1/4” of the temperature
probe is exposed to the air. Failure to do so may interfere with
the ability to sense tempera-ture and may result in excessive
steam room temperatures.
The exposed area of the temperature probe must
be free of silicone or any materials or obstructions that pre-
vent direct exposure to the steam room air. Failure to do so
may interfere with the ability to sense tem-perature and may
result in excessive steam room temperatures.
NOTE: For Illustrative Purposes Only. Drawings Not to Scale
1
AirTempo Operating Instructions
The AirTempo features programmable temperature
control, programmable time duration, AromaSteam
ON/OFF, ChromaSteam
®
control and two personal
settings.
The LCD will be OFF until a button is pressed. The
LCD remains lit for 10 seconds after the last button
is pressed. When the steam generator turns OFF
the display will turn on and read OFF. While the
generator is steaming the LED above AROMA and
,"ÊÜÊ>ÌiÀ>ÌiÞÊv>ÃÊiÛiÀÞÊÓÊÃiV`ð
Diagram 1
Diagram 2
ON/OFF
Time
ON/OFF
Diagram 1
Press the ON/OFF key for 1 second to start the
vÜÊvÊÃÌi>°Ê/iÊ/i«iÀ>ÌÕÀiÊ-iÌÊ*ÌÊÃÊ
`ë>Þi`°Ê-Ìi>ÊÜÊLi}ÊÌÊvÜÊ>ÊviÜÊÕÌiÃÊ
after the control is turned ON. The duration re-
quired for the steam room to reach steam bathing
temperatures depends on the steam room
construction and steam generator specifications. /Ê
ÃÌ«ÊÌiÊvÜÊvÊÃÌi>ÊLivÀiÊÌiÊiÝ«ÀiÃÊ«ÀiÃÃÊ
ÌiÊ" É"ÊiÞ°ÊÊ-Ìi>Ê>ÞÊVÌÕiÊÌÊvÜÊ
for a short time after the control is turned OFF
SETTING THE STEAMBATH DURATION
Diagram 2
Press TIME key to set or display the steambath
duration time. The control is pre-set and will display
a TIME setting of 20 minutes (default setting). With
the TIME displayed, press the LEFT or RIGHT
arrows to set the desired duration time (2-60
minutes) in two minute increments.
Set the steam bathing temperature
according to personal preference, however it is
highly recommended to begin steam bathing at a
low temperature setting for a very short duration to
gauge comfort and safety levels.
!
WARNING
2

7
®Operating Instruction
Operating Instruction
SETTING THE TEMPERATURE
Diagram 3: Press TEMP key to set the desired temperature or display the temperature setting. The control
is preset and will display a temperature setting of 110˚F (default setting). With the temperature displayed,
press the LEFT or RIGHT arrows to set the desired temperature (80°F to 120°F) in one degree increments.
Set the steam bathing temperature according to personal preference, however it is highly recommended
to begin steam bathing at a low temperature setting to gauge comfort and safety levels.
MEMORY FEATURE
If the control is turned off manually before it times out then the default settings of 20 minutes and 110°F
will be used the next time the control is turned on. If the control times out (not manually turned off) then
the previous user time and temperature settings will be used when the steambath is turned on.
USER PRESETS Diagram 4
Use the key program to store preferred settings.
To program preferred settings:
Press ON/OFF key to turn generator on. Press key once to program PROG1.
Press it twice to program PROG2. The selected setting will be displayed.
Enter the preferred time and temperature settings.
The AirTempo will store the following settings: Set point, Time duration & Aroma state.
To select PROG1 or PROG2:
Press ON/OFF key then press key once to select PROG1, press it twice to select PROG2.
The steambath will operate at the stored settings.
Diagram 3
Diagram 4
TEMP
Time &
Temperature
adjustment
User Preset
13
AROMA
CHROMA
AROMASTEAM
The AromaSteam is an optional accessory that automatically
injects aromatic oil into the steam. Press the ON/OFF key to
turn the steam generator on. Then, press the AROMA key.

>LÛiÌi>À>V° The AromaSteam turns off
automatically when the steam generator stops heating. Press
the AROMA key to turn it off during a steam session. The in-
dicator will turn off. To conserve battery life, the indicator will
only be lit when the display is ON.
CHROMASTEAM
The ChromaSteam is an optional accessory that provides
colored light in the steam room. Press the CHROMA key to
turn light on. Press twice to select the next color. Press again
to turn the light off. Note that the light can be turned ON
even if the steam generator is OFF. To conserve battery, the
>LÛiÌi>À>V will only be lit when the display is
ON.
TEMP
CHANGING THE TEMPERATURE UNITS (˚F/˚C)
When the generator is ON, press and hold the TEMP key for 10
seconds. The temperature units will toggle to Fahrenheit (F) or
Celsius (C).
USING AIRTEMPO AS A REMOTE
The AirTempo can be removed from its holder and used as a remote
control to warm up the steam shower. When AirTempo is returned to its
holder the steam generator will run for the full set duration. After 10 min-
utes the steam generator turns off if the AirTempo is not returned to its
dock. The steam generator will not restart unless AirTempo is in its dock.
USING
5VGCO.KPZK)GPKG WITH AIRTEMPO
-Ìi>ÝÉii will allow the steam generator to warm up the steam
room for 10 minutes. To continue the steam bath session press any
button on the AirTempo control. After 10 minutes the steam generator
turns off if the AirTempo is not touched. ÀÎäÕÌiÃ>vÌiÀÌiÃÞÃÌi
Ü>Ã]ÌiÃÌi>}iiÀ>ÌÀÜnot restart unless AirTempo is in its
dock.
AROMASTEAM
The AromaSteam is an optional accessory that auto-
matically injects aromatic oil into the steam. Press the
ON/OFF key to turn the steam generator on. Then,
press the AROMA key. LED above the aroma icon. The
AromaSteam turns off automatically when the steam
generator stops heating. Press the AROMA key to turn
it off during a steam session. The in-dicator will turn
off. To conserve battery life, the indicator will only be
lit when the display is ON.
CHROMASTEAM
The ChromaSteam is an optional accessory that pro-
vides colored light in the steam room. Press the
CHROMA key to turn light on. Press twice to select the
next color. Press again to turn the light off. Note that
the light can be turned ON even if the steam gener-
ator is OFF. To conserve battery, the LED above the
aroma icon will only be lit when the display is ON.
USING AIRTEMPO AS A REMOTE
The AirTempo®can be removed from its holder and used as a re-
mote control to warm up the steam shower. When AirTempo®is
returned to its holder the steam generator will run for the full set
duration. After 10 minutes the steam generator turns off if the
AirTempo®is not returned to its dock. The steam generator will
not restart unless AirTempo is in its dock.
USING SteamLinx/iGenie WITH AIRTEMPO®
SteamLinx/iGenie will allow the steam generator to warm up the
steam room for 10 minutes. To continue the steam bath session
press any button on the AirTempo®control. After 10 minutes the
steam generator turns off if the AirTempo®is not touched. For
30 minutes after the system was on, the steam generator will not
restart unless AirTempo®is in its dock.
CHANGING THE TEMPERATURE UNITS (˚F/˚C)
When the generator is ON, press and hold the TEMP key
for 10 seconds. The temperature units will toggle to
Fahrenheit (F) or Celsius (C).

8
®Operating Instructions
Maintenance Instructions
Replace the battery door and lock in place.
To prevent water from getting in the control, ensure the
battery doors are in the locked position before reinstalling control.
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the instructions.
Battery Replacement
The batteries in AirTempo will need periodic replacement. Both batteries
should be replaced at the same time with new CR2450 coin cell batteries.
CHOKE HAZARD. The batteries and battery doors are
small pieces, keep out of reach of children.
KEEP BATTERIES OUT OF REACH OF CHILDREN.
Swallowing may lead to serious injury or death in as little as 2 hours due
to chemical burns and potential perforation of the esophagus. Immedi-
ately see a doctor.
Remove the AirTempo from the wall by sliding it up and off the bayonet holder.
/iÊÀ/i«ÊViÃÊvvÊÌiÊyÕÃÊÕÌÊ`iÀÊLÞÊ}À>ë}ÊÌiÊLiâiÊ>`Ê«Õ-
}ÊÌiÊ>ÃÃiLÞÊÃÌÀ>}ÌÊÕÌÊvÊÌiÊyÕÃÊÕÌÊLÝ°
Use a soft cloth to dry off the control.
With two fingers turn the battery doors in the direction noted. The left battery
cover is opened by turning it clockwise, the right cover is opened by turning it
counterclockwise.
Discard both batteries and replace with new batteries, the positive side of the
battery goes towards the “+” symbol on the battery door.
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
System Status Codes
The AirTempo®may display a status code if the steam system is not
functioning correctly. When batteries are first installed in the control,
it will briefly display r followed by a number. This is the software
revision.
CO indicates the AirTempo®control has lost communication with the
steam generator. Ensure all connections are secure between the
steam generator and the transceiver.
Err P indicates an error while pairing, reset the control and redo pairing.
A complete list of steam generator status codes can be found in the
MrSteam Residential Steambath Installation Operation and
Maintenance Manual.
Prr1/2 Indicates are error with the internal (or MSTS) temperature
probe.
Err1 The incorrect field voltage is being supplied to the steam
generator (green LED on steam generator will be off).
H20/Errb: Steam generator water level is not satisfied.
Refer to the steam generator installation, operation and maintenance
manual for trouble shooting.
Pairing
AirTempos are factory paired, however if more than one
steam system is installed in close proximity the AirTempo®
controls must be paired to their wireless receiver to prevent
interference.
To pair AirTempo®use a blunt object to press the button in-
side the wireless receiver adjacent to the LED. Hold the but-
ton for 5 seconds, when the wireless receiver is in pairing
mode the LED will turn blink blue for 2 minutes.
While the transceiver LED is blinking, press and hold the
button on AirTempo®for until the display reads PAIR.
Care Tips for AirTempo®Controls and Steamheads
1. Use only mild soap and water on a soft cloth to clean the
control and steamhead.
2. Do not use abrasive cleansers
3. If the decorative cover is damaged call MrSteam technical
service for replacement parts.
Warranty
To register your steam generator unit online and to review the
MrSteam Limited Lifetime Warranty please go to:
blog.mrsteam.com/wr

(For North American Version)
FCC/Industry Canada Two Part Statement:
This device complies with FCC Part 15 and Industry Canada license exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Per Industry Canada RSS rules:
This device complies with Health Canada’s Safety Code. The installer of this
device should ensure that RF radiation is not emitted in excess of the Health
Canada’s requirement.
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le pro-
gramme d’installation de cet appareil doit s’assurer que les rayonnements RF
n’est pas émis au-delà de I’exigence de Santé Canada.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Les changements ou modifications non expressément approuvés par la partie
responsable de la conformité pourraient annuler l’autorité de l’utilisateur à
utiliser cet équipement.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
UÊ,iÀiÌÊÀÊÀiV>ÌiÊÌiÊÀiViÛ}Ê>Ìi>°
UÊVÀi>ÃiÊÌiÊÃi«>À>ÌÊLiÌÜiiÊÌiÊiµÕ«iÌÊ>`ÊÀiViÛiÀ°
UÊiVÌÊÌiÊiµÕ«iÌÊÌÊ>ÊÕÌiÌÊÊ>ÊVÀVÕÌÊ`vviÀiÌÊvÀÊ
that to which the receiver is connected.
UÊÃÕÌÊÌiÊ`i>iÀÊÀÊ>ÊiÝ«iÀiVi`ÊÀ>`É/6ÊÌiVV>ÊvÀÊi«°
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
9
®Maintenance Instructions
Maintenance Instructions
(For European Version)
DECLARATION OF CONFORMITY
Product: MrSteam AirTempo Control
Item Number: AirTempo
Equipment Class: III
AirTempo Control and Wireless Receiver
The objects of the declaration described here are in conformity with the
relevant requirements contained in the European 2014/53/EU Directive.
EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013.
ETSI EN 300 220-2 V2.4.1 (2012-05)
EN 301 489-3 V1.6.1 (2013-08)
EN 55032: 2012
EN 55024: 2010
Product name: AirTempo Mr.Steam
Product Type: AirTempo 43-20 34th Street
Brand: MrSteam Long Island City, NY 11101
CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT
BY PRIVATE USERS IN THE EUROPEAN UNION:
This symbol on the product or its packaging indicates this product
must not be disposed of with other household waste. Instead, it
is the user’s responsibility to dispose of their waste equipment by
handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or location where you pur-
chased the product.

10
Installation & Operating Instructions
®Maintenance Instructions
Technical Specifications:
Wireless Receiver Unit
Temperature operating -20 C ~ +50 C
Temperature storage -40 C ~ +85 C
Humidity 90%RH non-condensing
Usage type Indoor
Dimensions 41.5 x 117.5 x 22.5 mm (1.625 x 4.875 x 0.875 in.)
Operating frequencies 865 ~ 868 MHz (European Version)
910 ~ 920 MHz (North American Version)
Operating voltage 5.0 V (provided by Steam Generator Unit)
AirTempo Control Unit
Temperature operating -20 C ~ +60 C
Temperature storage -30 C ~ +60 C (limited by battery & LCD)
Humidity 100%RH condensing (external surface only)
IP Rating IPX5
Usage type Indoor
Dimensions 90.0 x 90.0 x 19.0 mm (without decorative bezel)
(3.625 x 3.625 x 0.75 in.)
Operating frequencies 865 ~ 868 MHz (European Version)
910 ~ 920 MHz (North American Version)
Operating voltage 3.0 V
Battery Type CR2450 Primary Manganese Dioxide
Lithium Batteries
(replace only with battery UL1642 approved)
Parts List:
Item # Description Used on
104554BK Electronic Assembly Black All
104554WH Electronic Assembly White All
104209 Retention Ring Flush Mount
(AirTempo Flush)
104210 Flush Mount Box Flush Mount
(AirTempo Flush)
104211 Surface Mount Holder Surface Mount
(AirTempo Surface)
104557 Wireless Receiver All
104213XX Round Bezel Flush Mount
(AirTempo Flush) (specify finish)
104214XX Square Bezel Flush Mount
(specify finish)
104215XX Surface Bezel Surface Mount
(AirTempo Surface) (specify finish)
104220 AirTempo Control Cable (3ft) All
104117-30 30 ft Control Cable Optional
103990-60 60 ft Control Cable Optional
MSTS 30 ft temperature probe Optional
MSTS-60 60 ft temperature probe Optional
Flush Mount AirTempo
U ,iÛiÊÌiÊÃÕÀv>ViÊÕÌÊL>ÞiÌÊvÀÊÌiÊL>VÊvÊÌiÊÀ/i«ÊVÌÀ°
/iÊÃÕÀv>ViÊÕÌÊL>ÞiÌÊÃÊÌÊÕÃi`ÊÜiÊyÕÃÊÕÌ}°Ê/iÊÃÕÀv>Vi
ÕÌÊ`iVÀ>ÌÛiÊLiâiÊÃÊÌÊÕÃi`ÊÜiÊyÕÃÊÕÌ}°
U 1Ã}ÊÌiÊÌi«>ÌiÊ«ÀÛ`i`ÊÊ«>}iÊÓÎ]ÊVÕÌÊÌiÊiÊÊÌiÊ`iÃÀi`ÊV>Ì°
Do not oversize or undersize the cutout. Ensure the template
is level before cutting the hole.
U /iÃÌÊwÌÊÌiÊyÕÃÊÕÌÊLÝÊÌÊiÃÕÀiÊÌiÊiÊÃÊÌiÊVÀÀiVÌÊÃâi°
U ÃÕÀiÊÌiÊÕÌ}ÊÃÕÀv>ViÊÃÊVi>Ê>`Ê`ÀÞ
U ««ÞÊ>ÊÌÊLi>`ÊvÊÃViÊÊÌiÊV>ÌÊÃÜÊ>ÃÊÀiµÕÀi`ÊÌÊVÀi>ÌiÊ>
moisture seal. Remove and discard the release paper to expose the adhesive
liner.
NOTE: The silicone supplied by MrSteam can be used for sealing and
gasketing. It cures to silicone rubber and adheres to glass, wood, metal,
porcelain, ceramic tile, painted surfaces, many plastics and rubber. Surfaces
must be clean and dry. Apply thin layer of product. Fit together and support if
necessary. Allow excess material to cure, then trim with a sharp blade. Sealant
“skins” in 5 minutes, dries to touch in 1 hour. Fully cures and bonds in 24 hrs.
Magnet
Do not apply excessive amounts of sil-
icone. Do not apply silicone to any other parts of the
control including the adhesive gasket. Place the flush
mount box into the hole.
The magnet in the flush mount box
should be orientated at the bottom of the box when
installed.
Flush mount components are sold separately (104232RD &
104232SQ). Contact a MrSteam representative if a flush mount kit is needed.

11
®
23
Place the electronic assembly into the decorative
bezel as shown. The retention ring snaps onto the
assembly from behind. The 3 piece assembly can then
LiÊ«>Vi`ÊÌÊÌiÊyÕÃÊÕÌÊLÝ°Ê/iÀiÊÃÊ>Ê>}iÌÊ
in the box that will hold the control in place.
Template
For Flush Mount Kit Installation
www.mrsteam.com
Products, information and specifications are subject to change without notice.
For more information call Sales & Support at: 1.800.76.STEAM
(East Coast) 1.800.72.STEAM (West Coast)
mr.steam [e-mail] www.mrsteam.com
43-20 34th Street, Long island City NY 11101 800 767 8326 I 9410 S. La Cienega Blvd., Inglewood CA 90301 800 727 8326
PN 100503 REV x°ÓÓ

Installation, Operation & Maintenance Manual
AromaSteam SteamHead
mr
.steam® Feel Good Inc.
PUR100421 Rev 5.22

!CAUTION
!CAUTION
mr.steam® STEAM HEAD
___________________________________________________________________________________________________________________________________________
INSTALLATION INSTRUCTIONS
mr.steam
®
[email protected] www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM
Steam
Supply Pipe
End of pipe to be recessed
1/4" (without Acrylic Shield)
1/8" (with Acrylic Shield)
1/8" minimum clearance required
when Acrylic Shield is used.
See installation instructions
provided with the Acrylic Shield.
Apply with silicone or
equal sealant as required
for moisture seal.
Use Teflon
®
or equal
sealant on pipe threads
Oil Well
STEP 3
STEP 4
STEP 5
Steamhead
(shown with
optional acrylic shield)
Locating Nipple
Drop Ear
Fitting
All drawings are for illustrative purposes only
3”
23/4”
31/2”
3”
1”
03”
7
/8”
IMPORTANT: See the Installation and Operation Manual
provided with the steam generator for additional important
steamhead & control installation and operation information.
Installation: Steam Head (1⁄2" NPT)
INSTALLER: Because the steam head and direct
steam emissions are very hot, locate the steam head where incidental
contact by bather with the steam head or direct steam emission cannot
occur.
STEP 1 Locate steam head 6-12 inches above floor, except for:
1. Tub/shower enclosures, install 6 inches above tub top edge.
2. For enclosures with acrylic or other non-heat resistant
flooring install Acrylic Shield Part Number MS-103938.
3. To prevent door seals from deteriorating do not locate the steam
head where direct steam emission would contact door seals.
STEP 2 Install steamhead with the oil well facing up as shown. Hand
tightening is sufficient when teflon or equal pipe thread sealing com-
pound is used.
IMPORTANT NOTE: to preserve steam head finish, do not use
wrench or other tools to tighten. DO NOT use abrasive cleansers or
chemicals. Use only water with mild soap and a non-abrasive sponge.
Consult with supplier of acrylic, fiberglass and other
non-heat resistant enclosures for recommended steamhead location.
Use Acrylic Shield part number MS-103938. See instructions provided
with steam shield.
STEP 3 Secure a bronze drop ear fitting to a header and run a 1/2"
copper steamline from the steam generator to the drop ear fitting.
Install a temporary nipple (6" or longer)in the drop ear fitting to locate
the steamhead after the wall is finished.
STEP 4 After the wall has been finished, mark on the nipple where the
surface of the wall is. Remove the nipple and measure the portion that
was in the wall (the end to your mark). Subtract 1⁄4" from that dimen-
sion and select a brass nipple of that length to finish the installation.
STEP 5 Wrap teflon tape around the threads of the new nipple and
screw the nipple into the steamhead. Do not use wrenches or tools
which would damage the steamhead's finish. Wrap teflon tape around
the threads of the nipple and screw the nipple and steamhead assem-
bly you just made into the drop ear fitting in the wall. The steamhead
should be flush with the wall and the well must be facing up.
PUR100421 Rev 5.22
13

Installation, Operation & Maintenance Manual
mr
.steam® Feel Good Inc.
Linear Steam Head
Residential Model: 1 04480
IMPORTANT: Leave this material with the homeowner.
PUR103936 Rev 5.22

!CAUTION
!CAUTION
mr.steam® STEAM HEAD
___________________________________________________________________________________________________________________________________________
INSTALLATION INSTRUCTIONS
mr.steam
®
[email protected] www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM
9410 S L Ci Bl d Il dCA 90301 tl1800 72 STEAM
Steam
Supply Pipe
End of pipe to be recessed
1/4" (without Acrylic Shield)
1/8" (with Acrylic Shield)
1/8" minimum clearance required
when Acrylic Shield is used.
See installation instructions
provided with the Acrylic Shield.
Apply with silicone or
equal sealant as required
for moisture seal.
Use Teflon
®
or equal
sealant on pipe threads
Oil Well
STEP 3
STEP 4
STEP 5
Steamhead
(shown with
optional acrylic shield)
Locating Nipple
Drop Ear
Fitting
All drawings are for illustrative purposes only
3”
23/4”
31/2”
3”
1”
03”
7
/8”
IMPORTANT: See the Installation and Operation Manual
provided with the steam generator for additional important
steamhead & control installation and operation information.
Installation: Steam Head (1⁄2" NPT)
INSTALLER: Because the steam head and direct
steam emissions are very hot, locate the steam head where incidental
contact by bather with the steam head or direct steam emission cannot
occur.
STEP 1 Locate steam head 6-12 inches above floor, except for:
1. Tub/shower enclosures, install 6 inches above tub top edge.
2. For enclosures with acrylic or other non-heat resistant
flooring install Acrylic Shield Part Number MS-103938.
3. To prevent door seals from deteriorating do not locate the steam
head where direct steam emission would contact door seals.
STEP 2 Install steamhead with the oil well facing up as shown. Hand
tightening is sufficient when teflon or equal pipe thread sealing com-
pound is used.
IMPORTANT NOTE: to preserve steam head finish, do not use
wrench or other tools to tighten. DO NOT use abrasive cleansers or
chemicals. Use only water with mild soap and a non-abrasive sponge.
Consult with supplier of acrylic, fiberglass and other
non-heat resistant enclosures for recommended steamhead location.
Use Acrylic Shield part number MS-103938. See instructions provided
with steam shield.
STEP 3 Secure a bronze drop ear fitting to a header and run a 1/2"
copper steamline from the steam generator to the drop ear fitting.
Install a temporary nipple (6" or longer)in the drop ear fitting to locate
the steamhead after the wall is finished.
STEP 4 After the wall has been finished, mark on the nipple where the
surface of the wall is. Remove the nipple and measure the portion that
was in the wall (the end to your mark). Subtract 1⁄4" from that dimen-
sion and select a brass nipple of that length to finish the installation.
STEP 5 Wrap teflon tape around the threads of the new nipple and
screw the nipple into the steamhead. Do not use wrenches or tools
which would damage the steamhead's finish. Wrap teflon tape around
the threads of the nipple and screw the nipple and steamhead assem-
bly you just made into the drop ear fitting in the wall. The steamhead
should be flush with the wall and the well must be facing up.
15

16
Linear Steam Head
®
®
Installer Section Model 104480
Steambath controls feature an integral or
remote temperature sensor that senses room temperature.
Install the linear steam head in a location where steam
emission will not come in direct contact with the control or
remote temperature sensor. Failure to follow these
instructions may result in poor temperature control, a
hazardous condition, scalding or personal injury.
Only use the supplied high temperature
silicone sealant as required to create a permanent moisture
seal. Do not seal the steam head with grout or any other
material. Failure to follow these instructions may result in
leaks, and cause problems associated with leaks, moisture
and property damage from leaks.
The linear steam head must be installed by a
qualified and licensed plumber. Failure to use a qualified
and licensed plumber may result in a leak within the wall
cavity and cause problems associated with leaks, moisture
and property damage from leaks. Failure to follow these
instructions may result in elevated temperatures, a
hazardous condition, scalding or personal injury.
Do not use black iron, galvanized, or plastic
pipe for the steam line. Use only properly rated brass pipe
or copper tubing in accordance with national and local
plumbing codes. Using any piping material other than
properly rated brass or copper piping may cause linear
steam head damage and problems associated with leaks,
moisture and property damage from leaks or steam.
Plumb rigid copper tubing or brass pipe from
the steam generator to the linear steam head. Plumbing
must not form traps or valleys. Failure to follow these
instructions may result in leaks, and cause problems
associated with leaks, moisture and property damage from
leaks. Failure to follow these instructions may result in a
hazardous condition, scalding or personal injury.
Do not modify or alter the linear steam head.
Do not cover, block or insert any product that is not a
MrSteam supplied linear steam head accessory with the
linear steam head. Failure to follow these instructions may
result in a leak within the wall cavity and cause problems
associated with leaks, moisture and property damage from
leaks. Failure to follow these instructions may result in a
hazardous condition, scalding or personal injury.
Do not disassemble the steam head. The steam
head is shipped fully assembled and requires no additional
assembly. Failure to follow these instructions may result in a
leak within the wall cavity and cause problems associated with
leaks, moisture and property damage from leaks.
Before installing the linear steam head, read
and follow the Installation and Operation Manual(s) provided
with all system components ( generator, controls,
accessories...etc.). If the installation and operation manuals are
not available go to www.mrsteam.com for an online copy, or
contact MrSteam Customer or Technical Services at 800-767-
8326 or 800-727-8326 for free copies. Failure to read and
follow all the Installation and Operation Manuals may result in a
leak within the wall cavity and cause problems associated with
leaks, moisture and property damage from leaks. Failure to
follow these instructions may result in inoperable system
components, a hazardous condition, scalding or personal injury.
Consult with the manufacturer of any non-
heat resistant enclosures for elevated temperatures, steam,
moisture compatibility or for suitability for use with steam.
Failure to follow these instructions may result in the damage
or failure of materials or products. Failure to follow these
instructions may result in leaks, and cause problems
associated with leaks, moisture and property damage from
leaks. Failure to follow these instructions may result in a
hazardous condition, scalding or personal injury.
Do not install a Linear Steam Head in an
acrylic/fiberglass tub or shower enclosure. Failure to follow
these directions may cause problems associated with leaks,
moisture and property damage from leaks. Failure to follow
these instructions may result in elevated temperatures, a
hazardous condition, scalding or personal injury.
Do not locate the steam head where steam,
elevated temperatures, moisture or water can contact any
products, wall surfaces, materials, door seals, devices,
electronics that are not designed for use with steam,
elevated temperatures, moisture or water. Failure to follow
these instructions may result in damage or improper
operation of the products, wall surfaces, materials, door
seals, devices or electronics.
The optional diverter reduces the steam
emission zone by redirecting steam up the wall above the
steam head (see page 6). Installation of the diverter may
result in the following:
• Changes to the steam distribution in the room
• Increase of the temperature of the wall and devices above
the steam head
• Surface condensation patterns on the walls and ceiling
Always test the diverter to insure proper safety, installation
and comfort.
Carefully inspect the Linear Steamhead and
packaging for shipping damage. In the event of shipping
damage, please contact the carrier for claim information.
Our customer service department can assist you with
product replacement.
Do not use abrasive cleansers or chemicals to
clean the linear steam head. Use only water with mild soap
and a non-abrasive sponge. The use of abrasive cleansers or
chemicals will damage the finish on the linear steam head.

Linear Steam Head
®
®
NOTE: Drawings are for illustrative purposes only. Consult with qualified designer, architect or contractor for steam room construction.
5
8"
2 1
8"
1 1
16 "
9 1
4"
2 1
4"
Slotted Mounting
Holes
Slotted Mounting
Holes
Steam
Outlet
Figure 2
3/4” NPT Steam Inlet
9-1/4”
1-1/16”
2-1/4”
5/8”
2-1/8”
P104481 - Linear Steam Head
104483 - Faceplate
104484 - Diverter
104482 - AromaTray
Bracket Adjustment Screws
Adjustable Brackets
Linear SteamHead
shown without the
optional faceplate
or diverter.
BOX CONTENTS:
• Linear Steam Head
• Faceplate
• Diverter
• AromaTray
• Silicone Sealant
• Installation Instructions
Model 104480
Figure 1
Dimensional Information
Installer Section
14”
14-1/8”- 19”
17

Flush or Recess 1
8"
CEMENT BOARD
Thin Set
Finished
Wall Surface
Silicone
Silicone
Steam Outlet Face
VAPOR BARRIER
Cement Board
Thin Set
Finished
Wall Surface
Silicone
Silicone
STEP 1. Confirm proper stud spacing: The studs
must have a minimum spacing of 14-1/8” and a
maximum spacing 19". If the stud spacing is outside
the required range then shim or otherwise reposition
the studs as required.
Installing the steam head between
incorrectly spaced studs may result in damage to the
steam head and result in a leak within the wall cavity
and cause property damage.
STEP 2. Locate the steam head 6-12” above the
finished floor. Locate the steam head where a steam
bather can not come into contact with direct steam
emissions. See page 6 for information on the steam
emission zone.
Steam is hot. Locate the steam head
where a steam bather can not come into contact
with direct steam emissions. Failure to follow these
directions may result in a hazardous condition,
scalding or personal injury.
STEP 3. Position the steam head between 2
properly spaced studs. Extend the adjustable
brackets as required so the steam head fits snugly
between two studs. Use a level to ensure the steam
head is level (see Fig. 3). Tighten the eight bracket
adjustment screws (supplied).
Linear Steam Head
®
®
NOTE: Drawings are for illustrative purposes only. Consult with qualified designer, architect or contractor for steam room construction.
Installer Section Model 104480
Figure 3
Figure 4
Steam Head Installation
Stud
Stud
Steam Head Face
Steam Outlet
Level
Copper Tubing
or Brass Pipe
(Not Supplied)
14
1
/8”- 19”
Linear SteamHead
shown without the
optional faceplate
or diverter.
Vapor Barrier
Steam Outlet Face
Bracket
Adjustment Screws
STEP 4. If the optional decorative faceplate is used,
see the installation instructions for the optional faceplate
on page 5. If the optional decorative faceplate is not used,
position the steam head so that the steam head face will be flush
with the finished wall face (see Fig. 4).
STEP 5. With the stem head properly positioned, with or without a
decorative faceplate, provide eight screws as required to securely
mount the steam head brackets to the studs.
Failure to position the steam head face as instructed may
result in improper steam head alignment, or a leak within the wall cavity
and cause problems associated with leaks, moisture and property
damage from leaks.
STEP 6. Plumb rigid copper tubing or brass pipe from the steam
generator to the steam head. Use a ¾” NPT fitting appropriate for the
steam piping used. Plumbing must not form traps or valleys. Thread
sealant must be used as required to ensure a leak free joint between
the piping and steam head.
STEP 7. Before continuing or closing the wall, test the installation,
piping and steam head for leaks, traps, position, steam emission zone
and for general proper installation.
Failure to test the steam head installation may result in
leaks, and cause problems associated with leaks, moisture and property
damage from leaks.
18

Installer Section
Linear Steam Head
®
®
NOTE: Drawings are for illustrative purposes only. Consult with qualified designer, architect or contractor for steam room construction.
Model 104480
The steam head is supplied with an optional faceplate. It
is not required for the functional operation of the steam
head. The faceplate is a decorative accessory and is
available in (8) finishes.
An optional Escutcheon (remodel plate) is available for
purchase, it's larger than faceplate and is available in (8)
finishes.
In STEP 4, instead of positioning the steam head face
to be flush with the finished wall face, position the steam
head so that the steam head face will be 1/8” recessed
with the finished wall (see Fig. 4). This will provide
clearance for the faceplate.
Apply silicone to the front of Linear Steam Head and
firmly press the faceplate against the face of the steam
head. Secure the faceplate as required until the silicone
sets.
Return to STEP 5 on page 4 to complete the
installation.
1. Determine the desired installation location of the control.
The iSteam®, iTempo™ and iTempo/Plus™ controls are
designed to be installed inside or out-side the steam room
as a matter of personal prefer-ence. If the control is installed
inside the steam room the control must be located:
2. 4-5 feet above the floor near the bather seating area
3. The control features an integral temperature sensor. Locate
the control in a location representative of the desired
steambathing temperatures.
Do not locate the control above or near the steam head or
direct steam emissions.
4. On a vertical wall
The control cable length is 30 feet. Insure that the control
and/or steam generator are located accordingly. An optional
60 foot cable is available, PN 103990-60 for iTempo and PN
104117-60 for iSteam. Contact a MrSteam technical service
representative if a 60 foot cable is required.
IMPORTANT NOTE: If the control is installed outside the
steamroom a Remote Temperature Probe Part Number MSTS
must be installed inside the steam room, depending on the
control. Insure MrSteam steam generator is iSteam or iTempo
compatible and has a serial number 900000 or higher. If
iSteam is used with a generator having serial number less than
1174000, contact MrSteam technical support for an upgraded
PC board.
See instructions for the MSTS Temperature Probe (located in
the Control Installation Manual related to your specific control
package) before rough-in or installation of control.
Figure 5
Optional Faceplate Installation
Cement Board
Thin Set
Finished
Wall Surface
Silicone
Faceplate
Silicone
Apply Silicone on surface
Faceplate
Figure 4
Vapor Barrier
19