Fencee Console User manual

Electric fencing Instructions
for use
EN
CONSOLE for solar panels
Thank you for purchasing a product from VNT electronics s.r.o.
The consoles are used to mount solar panels to boxes or holders.
IMPORTANT NOTIFICATIONS
• When installing, make sure you comply with all safety regulations.
• Before carrying out any work on electrical equipment, make sure that it is properly switched o.
• Please dispose the waste according to the applicable regulations.
• Never connect the solar panel directly to the energizer or battery.
Always use a regulator to avoid damaging the equipment!
CONSOLES OVERVIEW
Console (Art.No. 8163) for 40W panel (Art.No. 8145) for portable box (Art.No. 8150) ................ 3
Console (Art.No. 8185) for 40W panel (Art.No. 8145) for mounting post (Art.No. 8183) .............. 6
Console (Art.No. 8184) for 40W panel (Art.No. 8145) for security box (Art.No. 8151) ................. 7
Console (Art.No. 8164) for 100W panel (Art.No. 8146) for portable box (Art.No. 8150) ............. 10
Console (Art.No. 8186) for 100W panel (Art.No. 8146) for mounting post (Art.No. 8183) .......... 13
Console (Art.No. 8186) for 100W panel (Art.No. 8146) for security box (Art.No. 8151) ............. 14
Console (Art.No. 8165) for 200W panel (Art.No. 8147) for mounting post (Art.No. 8183) .......... 17
Console (Art.No. 8165) for 200W panel (Art.No. 8147) for security box (Art.No. 8162) ............. 21
1
www.fencee.eu I www.fenceefarm.com

Electric fencing
CONTENT
140W panel (Art.No. 8145) – console (Art.No. 8163) for portable box (Art.No. 8150) ........ 3
1.1 Console assembling .............................................................................3
1.2 Solar panel mounting ............................................................................4
1.3 Attaching the console holder to the box .........................................................5
1.4 Mounting on the box ............................................................................5
240W panel (Art.No. 8145) – console (Art.No. 8185) for mounting post (Art.No. 8183) ...... 6
2.1 Mounting to the mounting post ..................................................................6
340W panel (Art.No. 8145) – console (Art.No. 8184) for security box (Art.No. 8151) ......... 7
3.1 Console assembling .............................................................................7
3.2 Solar panel mounting ...........................................................................8
3.3 Mounting to the box .............................................................................8
Instuctions on how to build the
console for 40 W solar panel
[email protected]
[phone]
2

1. 40W panel (Art.No. 8145) – console (Art.No. 8163)
for portable box (Art.No. 8150)
1.1 Console assembling
Assemble the console parts according to the drawing and screw the parts together at
the marked points. Use 8 pcs M5 × 14 mm screw, 8 pcs M5 nut and 16 pcs M5 washer.
Vertical
console right Horizontal
consoles
Vertical
console left
Required material:
• 2 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 1 pc console holder
• 16 pcs M5 × 14 mm screw
• 16 pcs M5 nut
• 32 pcs M5 washer
• 2 pcs M6 × 110 mm screw
• 2 pcs M6 wing nut
·8 pcs M5 × 14 mm screw
·8 pcs M5 nut
·16 pcs M5 washer
3

1.2 Solar panel mounting
Screw the consoles according to the drawing with 4 pcs M5 × 14 mm screw,
4 pcs M5 nut and 8 pcs M5 washer to the panel.
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
4

Always orient the solar panel with the connection cable box facing upwards!
1.4 Mounting on the box
Place the solar panel with the console on the holder
so that both vertical parts of the console are seated
on the holder from the inside, connect the console
with the holder using 2 pcs M6 × 110 mm screw
in the marked spots as on the drawing and secure
them with 2 pcs M6 wing nut. The screws must pass
through all parts of the console and the holder.
1.3 Attaching the console holder to the box
Screw the console holder to the box according to the drawing and in the marked
spots. Use 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer.
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
·2 pcs M6 × 110 mm screw
·2 pcs M6 nut
5

Always orient the solar panel with the connection cable box facing upwards!
·2 pcs M10 × 120 mm screw
·2 pcs M10 wing nut
2. 40W panel (Art.No. 8145) – console (Art.No. 8185)
for mounting post (Art.No. 8183)
Required material:
• 2 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 12 pcs M5 × 14 mm screw
• 12 pcs M5 nut
• 24 pcs M5 washer
• 2 pcs M10 × 120 mm screw
• 2 pcs M10 wing nut
Console assembling – chapter 1.1
Solar panel mounting – chapter 1.2
2.1 Mounting to the mounting post
For mounting on the mounting post use a solar panel with a console. Panel with
console (for box portable Art.No. 8150) place on a mounting post screwed into the
ground so that the console is between the sides of the mounting post, secure the
panel in the marked holes, through both sides of the mounting post and both vertical
parts of the console with an M10 × 120 mm screw and an M10 wing nut. To secure
tilt of the panel, t a second M10 × 120 mm screw and an M10 wing nut, according
to drawing. The screws must pass through all parts of the console and the mounting
post.
6

·4 pcs M6 screw × 30 mm
·4 pcs M6 nut
·4 pcs M6 extended nut
3. 40W panel (Art.No. 8145) – console (Art.No. 8184)
for safety box (Art.No. 8151)
Required material:
• 2 pcs horizontal console
• 4 pcs M6 × 30 mm screw
• 4 pcs M6 nut
• 4 pcs M6 nut extended
• 4 pcs M5 × 14 mm screw
• 4 pcs M5 nut
• 8 pcs M5 washer
3.1 Console assembling
As shown in the drawing, screw onto the two vertical consoles 4 pcs M6 × 30 mm
screw, 4 pcs M6 nut and tighten, 4 pcs M6 nut extended, and tighten.
7

2 pcs horizontal consoles
3.3 Mounting to the box
Place the solar panel with screws against the box,
connect the panel wires to the wires on the box,
place the panel on the box on the inclined side into
the the prepared holes, secure the panel from the
inside of the box with 4 pcs M6 wing nut.
Always orient the solar panel with the connection cable box facing upwards!
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
3.2 Solar panel mounting
Screw the consoles with posts to the solar panel with 4 pcs M5 × 14 mm screw,
4 pcs M5 nut and 8 pcs M5 washer.
8

Electric fencing
Instructions on how to build the
console for 100 W solar panel
[email protected]
[phone]
CONTENT
1100W panel (Art.No. 8146) – console (Art.No. 8164) for portable box (Art.No. 8150) ...... 10
1.1 Console assembling ........................................................................... 10
1.2 Solar panel mounting ..........................................................................11
1.3 Attaching the console holder to the box ........................................................11
1.4 Mounting to the box ........................................................................... 12
2100W panel (Art.No. 8146) – console (Art.No. 8186) for mounting post (Art.No. 8183) ..... 13
2.1 Attachment to the grounding screw ........................................................... 13
3100W panel (Art.No. 8146) – console (Art.No. 8186) for security box (Art.No. 8151) ....... 14
3.1 Console assembling ........................................................................... 14
3.2 Solar panel mounting ......................................................................... 15
3.3 Mounting to the box ........................................................................... 15
9

Vertical console right
Horizontal
consoles
Vertical console left
·8 pcs M5 × 14 mm screw
·8 pcs M5 nut
·16 pcs M5 washer
Required material:
• 2 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 1 pc console holder
• 16 pcs M5 × 14 mm screw
• 16 pcs M5 nut
• 32 pcs M5 washer
• 2 pcs M6 × 110 mm screw
• 2 pcs M6 wing nut
1. 100W panel (Art.No. 8146) – console (Art.No. 8164)
for portable box (Art.No. 8150)
1.1 Console assembling
Assemble the console parts according to the drawing and screw the parts together at
the marked points. Use 8 pcs M5 × 14 mm screw, 8 pcs M5 nut and 16 pcs M5 washer.
10

1.3 Attaching the console holder to the box
Screw the console holder to the box according to the drawing and in the marked
locations, use 4 pcs M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer.
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
1.2 Solar panel mounting
Screw the console according to the drawing with 4 pcs
M5 × 14 mm screw, 4 pcs M5 nut and 8 pcs M5 washer
to the panel.
11

Always orient the solar panel with the connection cable box facing upwards!
1.4 Mounting to the box
Place the solar panel with the console on the
holder so that both vertical parts of the console
are seated on the holder from the inside,
connect the console with the holder using 2pcs
M6 × 110 mm screw in the marked spots as on
the drawing and secure them with 2 pcs M6
wing nut. The screws must pass through all
parts of the console and the holder.
·2 pcs M6 × 110 mm screw
·2 pcs M6 wing nut
By using the bottom screw,
you can adjust the solar panel
to three tilt positions.
12

Always orient the solar panel with the connection cable box facing upwards!
·2 pcs M10 × 120 mm screw
·2 pcs M10 wing nut
2. 100W panel (Art.No. 8146) – console (Art.No. 8186)
for mounting post (Art.No. 8183)
Required material:
• 2 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 12 pcs M5 × 12 mm screw
• 12 pcs M5 nut
• 24 pcs M5 washer
• 2 pcs M10 × 120 mm screw
• 2 pcs M10 wing nut
Console assembling – chapter 1.1
Solar panel mounting – chapter 1.2
2.1 Attachment to the mounting post
For mounting on the mounting post use a solar panel with a console. Panel with
console (for box portable Art.No. 8150) place on a mounting post screwed into the
ground, so that the plates of the screw are on the outside of the horizontal parts of
the console, secure the panel in the marked holes, through both sides of the mounting
post and both vertical parts of the console with an M10 × 120 mm screw and an M10
wing nut. To secure tilt of the panel, t a second M10 × 120 mm screw and an M10
wing nut, according to drawing, in one of the three positions. The screws must pass
through all parts of the console and the mounting post.
By using the top screw, you
can adjust the solar panel to
three tilt positions.
13

Vertical console left
Horizontal
consoles
Vertical console right
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
3. 100W panel (Art.No. 8146) – console (Art.No. 8186)
for security box (Art.No. 8151)
Required material:
• 2 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 4 pcs M6 × 30 mm screw
• 4 pcs M6 nut
• 4 pcs M6 nut extended
• 4 pcs M6 wing nut
• 12 pcs M5 × 14 mm screw
• 12 pcs M5 nut
• 24 pcs M5 washer
3.1 Console assembling
All parts are screwed together as shown on the drawing. Note the left vertical part is
assembled to the right and vice versa, use 8 pcs M5 × 14 mm screw, 8 pcs M5 nut and
16 pcs M5 washer. Screw the 4 pcs M6 × 30 mm screw onto the two vertical consoles
as shown, 4 pcs M6 nut and tighten, 4 pcs M6 nut extended, and tighten.
·4 pcs M6 × 30 mm screw
·4 pcs M6 nut
·4 pcs M6 extended nut
14

3.2 Mounting on the solar panel
Screw the console according to the drawing with 4 pcs M5 × 14 mm screw and 4 pcs
M5 nut and 8 pcs M5 washer to the panel.
3.3 Mounting to the box
Place the complete set with the mounted console to
the solar panel, against the box, connect the panel
wires to the wires on the box, place the panel on the
box on the inclined side into the the prepared holes,
secure the panel from the inside of the box with 4 pcs
M6 wing nut.
Always orient the solar panel with the connection cable box facing upwards!
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
15

Electric fencing
Instructions on how to build the
console for 200 W solar panel
[email protected]
[phone]
CONTENT
1200W panel (Art.No. 8147) – console (Art.No. 8165) for mounting post (Art.No. 8183) ... 17
1.1 Console assembling ........................................................................... 17
1.2 Solar panel mounting ......................................................................... 19
1.3 Mounting to the mounting post ................................................................ 20
2200W panel (Art.No. 8147) – console (Art.No. 8165) for security box (Art.No. 8162) ........ 21
2.1 Console assembling ........................................................................... 21
2.2 Solar panel mounting ......................................................................... 22
2.3 Attachment to the box ......................................................................... 23
16

1. 200W panel (Art.No. 8147) – console (Art.No. 8165)
for mounting post (Art.No. 8183)
Required material:
• 4 pcs horizontal console
• 1 pc vertical console left
• 1 pc vertical console right
• 12 pcs M5 × 14 mm screw
• 12 pcs M5 nut
• 24 pcs M5 washer
• 2 pcs M10 × 120 mm screw
• 2 pcs M10 wing nut
Vertical console left
Vertical
console right
Horizontal
consoles
1.1 Console assembling
Take the two horizontal parts of the console and put them over each other through, so
you have the eight holes as shown in the drawing, put M5 × 14 mm screw in one pair
of holes, 2 pcs M5 washer, and add one vertical part of the console. After catching
the nuts, add the other vertical part in the same way. In the same way, screw the two
horizontal parts to the other end of the vertical parts. Do not tighten the nuts.
This process of mounting of the 200 W solar
panel is also used when combined with a
portable box (Art.No. 8161).
17

·8 pcs M5 × 14 mm screw
·8 pcs M5 nut
·16 pcs M5 washer
18

1.2 Solar panel mounting
Screw the assembled consoles to the panel with 4 pcs M5 × 14 mm screw, 4 pcs M5
nut and 8 pcs M5 washer according to the drawing. Align the consoles with the panel
and tighten all screws.
·4 pcs M5 × 14 mm screw
·4 pcs M5 nut
·8 pcs M5 washer
19

1.3 Mounting to the mounting post
For mounting on a mounting post, we use a solar panel with a consoles. Mount the
panel with the consoles on a mounting post screwed into the ground, so that the
plates of the screw are horizontal on the outside of the consoles. Secure the panel
in the marked holes, through both sides of the screw and both vertical parts of the
bracket with an M10 × 120 mm screw and an M10 wing nut. To secure tilt of the panel,
t a second M10 × 120 mm screw and an M10 wing nut, according to one of the three
positions as shown. The screws must pass through all parts of the console and the
mounting post.
By using the top screw, you
can adjust the solar panel to
three tilt positions.
·2 pcs M10 × 120 mm screw
·2 pcs M10 wing nut
20