Foresight Sports SIM IN A BOX BIRDIE SIAB ENCLOSURE User manual

TABLE OF CONTENTS
SPECIFICATIONS 1
SAFETY INSTRUCTIONS 2
WHAT’S INCLUDED 3
OVERVIEW OF ENCLOSURE 4
FRAME ASSEMBLY 5-11
ENCLOSURE ASSEMBLY 12-17

SPECIFICATIONS
PRODUCT NAME
ENCLOSURE DIMENSIONS
RECOMMENDATIONS
WEIGHT
COLOR
SCREEN VIEWABLE
DIMENSIONS
RECOMMENDED SPACE
REQUIREMENTS
BIRDIE SIAB ENCLOSURE
8’4” (H) x10’10” (W) x17’ (D)
A STEP-STOOL OR LADDER WILL
BE NEEDED DURING
ASSEMBLY.
IT IS RECOMMENDED THAT AN
ADDITIONAL PERSON
ASSIST IN THE ASSEMBLY OF
THIS ENCLOSURE.
117 LBS.
BLACK SURROUND/FRAME
WHITE IMPACT SCREEN
7’7” (H) x10’1” (W) x12’7” (DIAG)
MINIMUM OF 12’ WIDTH,
18’ LENGTH, AND 9’ CEILING
HEIGHT
1

SAFETY INSTRUCTIONS
- Please pay close attention and make sure children, pets, and
other spectators are at a safe distance when swinging a golf
club inside the enclosure.
- Additionally, take every precaution to protect ceilings, walls,
windows, vehicles, and neighboring homes.
- Be alert of where you stand and walk, especially when others
are swinging golf clubs or hitting balls into the screen.
- Make sure the setup is far from gas lines, electric heaters,
replaces, candles, or any other source of heat or re hazard.
- When not in use, store neatly in a cool, dry location, and pro-
tected from weather elements and direct sunlight.
- Foresight Sports is not responsible for any damage to proper-
ty and/or any personal injury.
- Be mindful of disconnected and falling pipe if not snapped/
tightened properly.
- Do not hang from the enclosure.
2

WHAT’S INCLUDED
3
(18) COLOR CODED SNAP-BUTTON POLES
(1) PREMIUM IMPACT SCREEN
(1) BLACK NYLON SURROUND
(4) FOAM PADDING STRIPS
(2) L-SHAPED CONNECTORS
(6) 3-WAY CONNECTORS
(2) SIDE BARRIER NETS
(2) SAND BAGS
(80) BALL BUNGEES
BIRDIE
ENCLOSURE

OVERVIEW
4
The Premium Impact Screen was designed to allow the image to
ll in 100% of the screen, unlike other enclosure systems where
there is white space at the top and bottom. Constructed of pre-
mium materials, your golf simulator screen displays in HD quality
and is built tough to withstand golf ball strikes up to 250 MPH.
In independent, head-to-head
testing conducted by the team
at MyGolfSpy, with its mission to
inform and protect the golf con-
sumer with unbiased data-driven
methods, this Premium Golf Simulator Impact Screen outperformed what has
been the industry’s most popular impact screen on the market. The results
proved the durability of this new Premium screen is superior to the competi-
tion, while also delivering reduced sound and bounce back.
PREMIUM
IMPACT
SCREEN

FRAME ASSEMBLY
5
Lay out poles and connectors. Organize by color.
(4) PURPLE poles with a single stripe on one end and
double stripes on the opposite end.
(4) BLUE poles with single stripes on both ends.
1A
(3) YELLOW poles with single stripes on one end and
double stripes on the opposite end.

FRAME ASSEMBLY
6
1B
TIP: In the follow-
ing steps, you will
connect the GREEN
single stripe end to
the connector piec-
es. You will connect
the YELLOW single
stripe ends to the
ORANGE double
stripe ends.
(4) GREEN poles with single stripes on both ends.
(3) ORANGE poles with single stripes on both ends.
1B

FRAME ASSEMBLY
7
2Assemble the back lower poles rst. Attach a YELLOW
pole to an ORANGE pole. After, attach a 3-way con-
nector to each end.
REMEMBER: Connect the double striped end of the YEL-
LOW pole to the single striped end of the ORANGE pole.
And the 3-way connectors will attach to the single striped
end of each pole.
3Assemble the entire lower section by attaching (2)
GREEN poles to the 3-way connectors, and then at-
tach the (2) L-shaped connectors to the ends of the (2)
GREEN poles.

FRAME ASSEMBLY
8
4Connect (4) BLUE poles to the corner connectors that
will act as bottom uprights for the structure
TIP: At this point in the assembly, make sure button snaps
are fully engaged in each tting. Also, this would be a good
time to place the structure near its nal location due to the
added weight of the screen and surround in future steps.

FRAME ASSEMBLY
9
5Connect (4) PURPLE poles to the BLUE uprights to
complete the vertical assembly. Next, attach the (4)
remaining 3-way connectors to the open ends of the
PURPLE poles.

FRAME ASSEMBLY
10
6Start with the back section and attach (1) ORANGE
pole to the back-right 3-way connector. After, attach
(1) YELLOW pole to the ORANGE pole and then attach
that YELLOW pole to the back-left 3-way connector.
Repeat these same steps for the front facing upper
section.

FRAME ASSEMBLY
11
7To complete the frame structure, attach the (2) re-
maining GREEN poles to the open 3-way connectors
at the top.

ENCLOSURE ASSEMBLY
12
AIn this section, you will attach the black surround to
the frame, along with the impact screen. You will need
a ladder and it is recommended to have an additional
person to assist with the following steps.
Unfold the black
surround and
position it to the
outside of the
frame.
1) Make sure that
the velcro strips
of the surround
will be facing the inside of the frame.
2) Make sure the grommet holes of the surround are
positioned along the back of the frame.

ENCLOSURE ASSEMBLY
13
BUnfurl the black surround and bring it over the top of
the GREEN pole (with the assistance of another per-
son), and bring the surround across the structure so
that it crosses atop the opposite GREEN pole and then
down the opposite side of the frame.
Once the black surround is in
place, remove the velcro cov-
er strips to begin wrapping the
surround panels around the
poles.

ENCLOSURE ASSEMBLY
14
CTIP: Start by connecting the bottom aps of the black sur-
round by sliding the inside piece under the bottom pole
and then folding it up to secure it with the velcro strip.
Once the velcro is in
place, connect the
black surround with
the bungee balls. Re-
member to position
the balls to the inside
of the enclosure. Con-
tinue connecting the
surround with bungee
balls and then move
on to impact screen.

ENCLOSURE ASSEMBLY
15
DTIP: Before han-
dling the impact
screen, wash your
hands thoroughly
to avoid blemish-
es or stains on
the white materi-
al. And make sure
the oor is clean
too.
Begin by using (4) bungee balls to at-
tach the screen to the four corners.
The bungee cord should be thread-
ed through the grommet holes in the
screen, then wrapped around the
pole. Make sure the bungee ball is
positioned outside of the enclosure.
Repeat the bungee ball attachment
through every grommet hole of the
impact screen. Move to the back of
the screen and enclosure to attach the
back aps along the uprights. These
aps will conceal the bungee balls for
a nished look.

ENCLOSURE ASSEMBLY
16
EThe (4) foam pads can now be added to the enclosure.
There are (2) long pads that will be attached to the
velcro along the top and bottom of the screen, and
(2) shorter pads that will attach to the two sides of the
screen.
Match the angle pieces of the
foam (similar to a picture frame)
to complete the nished look of
the screen. Press along the top,
bottom and down the sides to
make sure the foam is complete-
ly attached to the enclosure.

ENCLOSURE ASSEMBLY
17
FTo complete the enclosure and to protect walls, win-
dows, and others from errant golf shots, add the side
barrier netting to the sides of the enclosure. Simply
attach the velcro side of the net along the front poles
and black surround velcro strip.
Start at the bottom with the velcro and run it up the
pole as high as possible. Once attached, the net can be
extend outward and connect to the provided sandbag.
Fill the sandbag with the appropriate amount of sand
that will then keep the side barrier netting extended
and taut.