Gprinter Gp-1124d User manual

Customer service hotline : 400 611 3828

Direct thermal Label Printer

User's Manual

GP-1124D / GP-1125D

CONTENTS

1. The printer .............................................................................................. 01

1.1 Introduction ..................................................................................... 02

1.2 Product features ..................................................................................... 03

1.2.1 Standard equipment ....................................................................................................... 03

1.3 Specifications ........................................................................................ 03

1.4 Print specifications ........................................................................................ 04

1.5 The paper size ................................................................................................. 04

2. Product introduction ................................................................................................ 05

2.1 Open and check .............................................................................................. 05

2.2 Printer components ................................................................................................. 06

2.2.1 Appearance ................................................................................................................................. 06

2.2.2 Internal ......................................................................................................................... 07

3. Installation ...........................................................................................08

4. LED indicator function .......................................................................................... 08

5. Troubleshooting .................................................................................................... 13

6. Maintenance ............................................................................................15

3.1 Install the printer ...................................................................................... 08

4.1 LED indicator ........................................................................................ 08

4.1.1 Direct thermal printing ................................................................................................. 08

4.2 Button Function ....................................................................... 09

4.3 Start function ......................................................................................... 09

5.1 Common problem ......................................................................................... 13

6.1 Printer Cleaning ...........................................................................................15

Direct Thermal Label Printer

4.3.1 Self-test ............................................................................................................10

4.3.2 Dump mode ......................................................................................................11

4.3.3 Printer Initialization ...........................................................................................11

4.3.4 Print DIP Switch function ..................................................................................12

4.3.5 Skip AUTO.BAS ...............................................................................................12

The printer

Introduction

Application Field

Manufacturing & Warehousing logistic industry

Healthcare

Parcel Post

Office & Studio

Retail

Product labeling and marking

Warehouse management label

Category marking label

Operation instruction marking label

Distributing instruction marking label

Patients marking

Medicine marking

Specimen marking

Mailing label

Price Label marking

Product item marking

Jewelry product marking

Thanks for choosing GP-1124D, GP-1125D series direct thermal label printer.

This series printer inner volume is fit for 5" OD (Outer Diameter) paper roll, if using external

paper holder, you can install 8.4"OD industrial grade label roll.

This printer is designed for real-time and batch label printing, with standard serial and USB

port. Direct thermal printing are available in printer body, you can choose various kinds of

printing materials, for example: thermal paper, plastic paper, fan fold paper etc.

Common 1D barcode and 2D barcode fonts are built inside printer, also it support 4 direction

printing, characters can be enlarged from 1 to 10 times. Besides, it supports 5 different size

bitmap fonts, OCR-A and OCR-B fonts, together with 203dpi higher print resolution, this

series printer are your best choice among the same class.

Declaration: This is a class A product, fit for Non Tropic regions installation. This product may

cause radio interference in life environment, users may need to take adequate preventive

measures.

Direct Thermal Label Printer

Product features

Standard equipment

Specifications

Support bar code Support picture format

Support picture format

Power Supply

Printer weight

Models

Printer size

Can print text, bar code, pictures

Product standard

Thermal printing

ABS plastic housing

Gap sensor

The print head open sensor

Communication interface

Memory

The paper key and LED indicating lamp

Built in 8 dot matrix font English number

The character and the bar code can be printed in four directions

of rotation (0,90,180,270) degree.

Built in simplified Chinese, traditional and Korean font for

programming.

The built-in voltage automatic switching power supply

Work environment Dampness

Dampness

Storage environment

203DPI/300DPI

GP-1124D GP-1125D

180(W) X 176(H) X 238(D) mm

Black mark sensor

Interface USB USB + Series

Direct Thermal Label Printer

Print specifications

Models

The print head

Print mode

1. 5 The paper size

Pulse excitation

(the size) (width X length)

Print speed (inches per second)

Maximum print width

Maximum print length

Heat sensitive piece (wear)

Label length

The paper height gap spacing

Roll axis size

The thickness of the paper

(tag + bottom paper)

The width of the paper

(tag + bottom paper)

The paper winding form

Paper type

The maximum capacity of

internal paper roll diameter

Print out of plane roll / print surface involute

Continuous paper, gap of paper, paper folding, punched paper

Note: If you use the tag length less than 25.4mm (1 "),

recommend the use of a perforated line in the gap on

the label paper so the tear.

50km

Max.118mm (4.64")

GP-1124D GP-1125D

203dots/inch(8dots/mm)

0.125x0.125mm

(1mm = 8dots)

2~8 inch/s

Direct thermal

Direct Thermal Label Printer

Product introduction

Open and check

This series printer is with special package to prevent damage in transportation. If there is

any unexpected damage occurred, please put in clean and stable surface and carefully open

the package to check, inform local distributor with damage details, and keep packing mate

-rials well in case you need to mail the printer.

Packing list:

◆ One Label printer



◆ CD ( Driver, Nice label software, User Manual )



◆ Power Adapter



◆ Power Cord



◆ USB cable ( Serial cable optional)



◆ Label roller & Label paper

Please pack equipment and materials needed for safekeeping printer for subsequent handling;

if the above items, any lost or missing, please Customer Service Department of your purchase

contact.

Direct Thermal Label Printer

Printer components

Appearance

LED lights indicate:

★ ON LINE electric ★ ERROR error indicatorindicator

Label exit

LED indicator

Press button for top cover open

Direct Thermal Label Printer

Internal

Note: Picture showing printer port is for GP-1125D.

Label paper fixing stand

Label paper supply hub

Push button for thermal

print head open

Top cover

2.2.3 The bottom

RS-232C serial port

DIP switch

Label entrance from

external holder

Push button for thermal

print head open

Power port

USB port

Direct Thermal Label Printer

Installation

Install the printer

1. Please put the printer on the stable surface.

2. Make sure printer power is turned off, please do not plug

the power cable when the printer power is turned on.

3. Connect serial or USB or Parallel or Ethernet cable to

printer and PC.

4. Connect power plug to power supply socket.

Be careful:

※ Please turn off the power switch the printer in the power socket,

※ Transmission interface in the picture will vary depending on your printer

purchased aircraft type, the actual transmission interface, please refer to

the corresponding product specifications

power line is inserted into the printer.

LED Indicator and Function

There’re two buttons and three LED indicators, many functions can be realized through using

different button, indicator and power on/off switch.

LED indicator

Direct thermal printing method

LED Indicator status Descriptions

Power indicator is on，Error indicator is off Printer is powered on and in normal

printing status

Power indicator flashes every 640ms,

Error indicator is off

Printer is paused

Power indicator is off, Error indicator goes

for 80ms, then goes off for 160ms, printer

start beeping.※

on Printer cover is opened

Power indicator is off

for 500ms, then goes off for 6s

, Error indicator goes on Label gap detection error

Power indicator is off Error indicator flashes

every 160ms, after two times flashing, Error

indicator goes off for 320ms, printer start

beeping. ※

, Paper out

Power indicator is off Error indicator flashes

every 160ms,after three times flashing,Error

indicator goes off for 320ms, printer start

beeping. ※

, Black mark detection error

Error indicator flashes every160ms. Printer overheated protection mode is act-

ivated. After 1 minute, the printer CPU will

check print head temperature again. When

temperature return normal, printer will work

normally.

Direct Thermal Label Printer

Button Function

Feed

When the printer is ready (LED blue fixed), click the button, label paper into the front end of a paper label.

Print job timeout

The printer in the print, click the PAUSE button to print suspended. At this time power indicator is

blue flashing. Just click the button, the print job resume normal.

Start function

The printer has five kinds of power function can be used to set or test the printer hardware. In the

boot and press the button with lamp signal release key can start these functions.

Five Power-up Functions:

Function Descriptions

Self-test page A.Turn off the printer.

B.Make sure the paper roll is installed correctly and the printer

top cover is closed.

C.Press and hold FEED button and turn on the printer. Self-test

page will be printed, then release FEED button.

You can use this function to check if printing function is normal or not.

Print DIP Switch page

Debugging Mode

A.Turn off the printer.

B.Make sure the paper roll is installed correctly and the printer

top cover is closed.

C.Press and hold PAUSE button and turn on the printer. When

paper feed and then release PAUSE button, DIP switch page will

be printed out.

A.Turn off the printer.

B.Make sure the paper roll is installed correctly and printer top

cover is closed.

C.Press and hold PAUSE and FEED button, and turn on the

printer. When Power indicator(blue) and Error indicator (red)

are on at the same time, release PAUSE and FEED button,

printer goes to Debugging Mode, and you will find below page

printed out:

Printer Initialization A.Turn off the printer.

B.Press and hold PAUSE and FEED button, then turn on the

printer. When Power indicator(blue)is on and Error indicator

(red) is off, release PAUSE and FEED button, all data in pri-

nter DRAM will be cleared and printer setting will be restored

to factory default setting. Then power indicator will be on and

printer goes to ready status.

Skip AUTO.BAS program

User can use TSPL2 command to save a code auto-

running file (AUTO.BAS) into flash. When turn on printer,

printer will run the program automatically.

If you want to skip AUO.BAS program on power-up,then

follow below steps:

Press and hold PAUSE and FEED button, then turn on the

printer. When Power indicator (blue) is off and Error indi

-cator(red)is on, release PAUSE and FEED button, printer

will skip running AUTO.BAS program, and then Power

indicator will be on.

Direct Thermal Label Printer

4.3.1 Self-test

To start the printer self-test, please follow the steps:

1. Turn off the printer power.

2. Make sure the paper roll is installed correctly and the printer top cover is closed.

3. Press the FEED button and turning on the printer power simultaneously. When the

self-test paper comes out, release the FEED button.

Self-test page sample:

GP-1125D

*The self-test page of GP-1124D and GP-1125D will has some difference.

Direct Thermal Label Printer

The printer configuration after the initialization will revert to the default values are as follows:

Parameter Default setting

Speed

Density

Gap

Direction

4inch/sec (101.6mm/sec),

0mm

203dpi

OFF

CLEAR

NOT CLEAR

Top left corner from printing direction

Printing content are placed on page from

top to bottom

Reference

SHIFT

OFFSET

SET TEAR

SET HEAD(Cover open detect)

Set PRINTKEY

SET REPRINT

SET KEY1(FEED)

SET KEY2(PAUSE)

CLEAR RAM

CLEAR FLASH

4.3.3 Printer Initialization

Printer initialization is used to clear DRAM and restore printer settings to defaults.

Please do the gap sensors sensitivity calibration after the printer initialization.

Please follow the steps below to initialize the printer:

1. Turn off the printer power.

2. Press and hold on the PAUSE button and FEED button, then turn on the printer

power. When the POWER indicator (blue light) dims and ERROR indicator (red light)

light, release both buttons. The printer DRAM is cleared and printer settings are

restored to defaults.

4.3.2 Dump mode

Please follow the steps:

1. Turn off the printer power.

2. Make sure the label roll is installed correctly and the printer top cover is closed.

3. Press and hold on the PAUSE button, then turn on the printer power. When the

POWER indicator (blue light) and ERROR indicator (red light) light simultaneously,

release the buttons. The printer is changed to Dump mode and print as below chart..

Printer will not print if data is not more than one piece of label, and need to press

FEED button to force the printer to print it out.

*********************

Direct Thermal Label Printer

4.3.4 Print DIP Switch function

Print the DIP switch page as follow:

A.Turn off the printer.

B.Make sure the paper roll is installed correctly and the printer top cover is closed.

C.Press and hold PAUSE button and turn on the printer. When paper feed and then

release PAUSE button, DIP switch pagewill be printed out.

DIP SWITCH FUNCTION:

SW1 POWER ON TEST PAPER

OFF ENABLED

ON DISABLED

SW2 SELECT THERMAL DENSITY MODE

OFF ENABLED

ON DISABLED

SW3 SW4 SELECT BAUDRATE

OFF OFF 9600

OFF ON 19200

ON OFF 38400

ON ON 115200

4.3.5 Skip AUTO.BAS

User can use TSPL2 command to save a code auto-running file (AUTO.BAS) into

flash. When turn on printer, printer will run the program automatically.

If you want to skip AUO.BAS program on power-up, then follow below steps:

1.Turn off the printer power.

2.Press and hold PAUSE and FEED button, then turn on the printer.

3.When Power indicator (blue) is off and Error indicator(red) is on, release PAUSE

and FEED button.

4. The printer will skip running AUTO.BAS program, and then Power indicator lights.

Direct Thermal Label Printer

Problems Possible Reasons Solution and Suggestion

Power indicator

not "ON”

Troubleshooting

Common problem

Below the table of contents is generally the common problems and solutions; if you have been in

our proposed methods of eliminating the fault, and the printer is not normal operation, so check

with your purchase customer service department, so as to get more help.

Plug to AC outlet and plug to

printer not well connected

Check power connector and AC outlset

if plugs are correctly connected

Printer power not turned on Turn on power switch

Print head not well closed Close print head by pressing whole print

head mechanism (or 2 arrow locations)

Label paper jamed inside printer

Label paper end Change new label paper

Label paper improperly installed Refer to Paper Installation steps in User

Manual to re-install paper

Gap sensor detection error Adjust paper specification and print again

Clear jamed paper

Not printing

Serial cable improperly

connected

1. Check if Pin configuration in cable two

sides are matching each other;

2. Check if baud rate setting on PC and

printer are the same, If in TPSL comma

-nd mode, We suggest 9600, n, 8, 1 to

ensure higher reliability.

3. Change a new cable.

Ethernet cable improperly

connected

1.Check if RJ-45 green/orange LED

indicator is on. When printer receive

and process printing data, LED will be

orange color;

2.Check if printer IP is assigned in

DHCP mode.

3.Check if fixed IP address is correctly

set in printer property. Wait for some

minutes to make sure printer is connect

-ed server and printing a selftest page

to confirm printer IP address.

4.Change a new ethernet cable.

USB cable improperly

connected

Check if USB cable connected well or

change a new cable

Direct Thermal Label Printer

Not printing

Print head not clean Clean print head and print again

Print density setting wrong Suggest density set to be 7

Print head cable not well

connected

Re-connect print head cable

Step Motor cable not well

connected

Re-connect step motor cable

Command setting wrong Check if there is PRINT command

at the end of printing file;

or if there is CRLF command at the

end of every line.

Not good

printing quality

Label improperly installed

Too much dust or adhesive on

print head

Re-install label

Clean print head and print again

Print head damaged Take selftest page to check if printing

are completely to confirm if necessary

to change new print head

Data miss printing

in one or two sides

Label paper size wrong

setting

Check if label size set correctly and

same as your label paper

Wrinkle

Printing not stable Printer in HEX Dump mode or

RS-232 setting wrong

Print head unbalanced stress;

Label improperly installed;

Label feeding not smoothly

Reset the label print density and

adjust paper width fixing stand to

fit your label paper size.

Restart your printer and leave Dump

Mode or reset RS-232 PARAMETER

Direct Thermal Label Printer

Maintenance

6.1.Printer Cleaning

To ensure the printing quality, please proceed this maintenance section to keep your printer

in good conditions and extend its life as well.

Please use one of following material to clean the printer.

★ Cotton swab

★ Lint-free cloth

★ Vacuum / Blower brush

★ 100% ethanol

2.The cleaning process is described as following：

Parts to be cleaned Step Recommend cleaning frequency

Print head

Rubber roller

Paper tear bar

Sensor

Inner side of printer

1.Turn off the printer.

2.Allow the print head to cool for

at least one minute.

3.Use a cotton swap and 100%

ethanol to clean the print head

surface.

When change new label paper

Print mechanism Print mechanism

Print head

1.Turn off the printer.

2.Rotate the platen roller and use

a cotton swap to clean with

100% ethanol.

When Change new label paper

Use a cotton swap and 100%

ethanol to clean.

When necessary.

Use air brush or vacuum to clean

dust of sensor.

Monthly.

Use air brush or vacuum to

the dust.

clean

Note：

※ Always turn off the printer power before cleaning the printer.

※ Do not touch print head by figure.

※ Please use 100% ethanol, Do not use medical alcohol to aviod damage to print head.

Direct Thermal Label Printer

Other manuals for GP-1124D

This manual suits for next models

Table of contents

GPRINTER GP-1124D User manual