Hangar 9 Spitfire Mk.IX ARF User manual

Spitfire Mk.IX ARF
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)
This R/C airplane is not a toy!
Specication:
Wing Span: 2058mm/81in
Length: 1715mm/67.5in
Flying Weight: ~7.6kg
Wing area: 74.95 dm2
Engine: 35cc-40cc
R/C System: 2.4Ghz 6ch
Servo: GP *7 ; EP * 6
Battery: LI-PO 5S*2 5000mAh 30C
ESC: 120A High voltage Brushless ESC
Electric retract system
Receiver
7.4V 30C
For retracts
4.8V
For receiver
In order to let the customers have
more choices, we don't provide a
uniform plugs.
4. Assemble the electric retracts to the plane
after several times smoothly running.
Please don't ceaselessly turn and off the switch in 2 seconds,
if you do this way, the circuit board will be heated.
Thank you very much for purchasing our TRCM optional electric retract set,
all our products were passed strict QC before they shipped out to the customers.
In order to avoid probably trouble happen, we still would like you to follow the steps
below before you assemble our electric retracts to your plane.
1. Connecting the circuit board to the battery and receiver.
2. Turn on the radio control to check the lights
on the circuit board, if the lights turn on green
or turn on red orderly，0.5 second after each
from the right to the left and all the lights will
turn off after 15 seconds, then the circuit will
work normally. Otherwise the circuit will be a
defective one if you make sure the setting on
your radio control are correct, please don't use
it but contact with your supplier in time.
3. Link the electric retract units to the
circuit boards after the above two
steps, check again the electric retracts
to see if they can work normally or not.
1

35cc gas engine
Engine 19″X10
Motor 21″X12
6
86
6
6 channel radio for aiplane is highly recommended for this model.
9Optional electric retract set
We strongly recommen you use the thread lock for all the screws when you build your model.
4.25 in scale spinner
Motor: Outer rotor, 63-60 220KV
Gasoline tube
Gasoline
Accessories packing list
13
8
TP Screw (3x20mm )
12
TP Screw (2.3x8mm)
1
Tail wheel (45mm)
Main wheels (100mm)
6
6
Copper joiner
1
Linkage Stopper 2
Plastic tube (2x650mm)
Fuel tank (550cc) 1
4
Steel wire (0.5x3000mm)
4
2
15
pivot & round hinge(5x68mm)
2
Screw (6x50mm)
1
Gear door
6
Pin hinge(24x24mm)
24
4
TP Screw (2.3x12mm)
Horn(2mm) 6
Horn(2mm) 2
16
Clevis
16
16
Screw (2x10mm)
16
Screw (3x16mm)
16
Washer(2x5mm)
Servo tray(2mm)
2
Push rod (2x115mm)
8
Purchased separately
2
1
1
2
4
Wooden Block
Circlip
2
Retracts strut
circuit board
Oleo struts
Screw (2.6x12mm) 5
2
Washer(3x10mm)
1
EVA(10mm)
2
Wooden Block
2
Wooden Block
2
Wooden Block
5
Screw (3x10mm)
21
Washer(3x6mm)
1
Screw (4x15mm)
1
1
2
Fiber deconations
1
scoop
1
Antenna
3
Screw (3x20mm)
2
Scale gun set
1
Canopy Fiberglass
1
Canopy PVC
carbon ber tube(10x285mm)
Aluminum tube
2
Push rod (2x70mm)
Main wing joiner(20x420mm)
1
Push rod
1
Tail gear
1
Alu clevis
16
Screw (3x5mm)
L bracket
Optional box for motor
Ply sheet (3mm)
Locknut (2mm )

Scale gun set
Scale gun set
Assemble the canopy to the cockpit with screws.
Assemble the cockpit to the fuselage.
Assemble the scale gun set to the wing and the ber
scoop to the fuselage.
1.5mm
TP Screw (2.3x8mm)
8
TP Screw (2.3x8mm)
Blind Nut
2
Screw (3x20mm)
200mm
253mm
Epoxy the ber deconations to aprropriate position
on the bottom of the wing.
The centre of the Gravity.
The skech map of the Spitre plane install
completion.
130 mm
130 mm
scoop
63
64
61
12
65
60
62
2
Servo tray(68.5x56.5x2mm) Securely glue together. If coming o during ights, you 'll
lose control of your airplane which leads to accidents!
Make sure hinges are
mounted in the same line.
6
Pivot & round hinge(5x68mm)
6
4
Clevis（2mm)
4
4
Screw (2x10mm)
8
Screw (3x5mm)
Locknut (2mm )
2
Push rod （2mm)
4
Washer(2x5mm)
8
Horn 2
1mm
Aileron
Trailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Ball joint
Ball joint
Lock Nut (2mm )
Lock Nut (2mm )
Washer(2x5mm)
Washer(2x5mm)
Screw (2x10mm)
Screw (2x10mm)
4
Screw (3x5mm) 8
4
4
Screw (2x10mm)
Nut (2mm )
4
Washer(2x5mm)
Horn 2
Pivot & round hinge(5x68mm)
4
Pivot & round hinge(5x68mm)
8
Washer(3x5mm)
Washer (3x6mm)
Screw (3x5mm)
8
Washer(3x6mm)
L bracket
L bracket
L bracket
Push rod （2mm)
Screw (3x16mm)
Install the L brackets to the servo of aileron as
illustration below.
Install the nylon control horn and connect the linkage.
Apply instant AB glue to aileron and pin hinge.
Assemble the aileron to main wing with instant type AB glue. Be careful
to ensure the moving parts of the hinges are able to move freely.
Keep some space about 1mm width between the
trailing edge and the aileron.
1
2
3
4
5
1
Accessory list for the coming installation steps.

Securely glue together. If coming o during ights, you 'll
lose control of your airplane which leads to accidents!
Flap
1mm
Make sure they are in
the right position while
installing.
Trailing
edge
TP Screw (3x16mm)
TP Screw (2.3x12mm) 8
1.5mm
6
Pin hinge(24x24mm)
Masking tape
2
Servo tray(68.5x56.5x2mm)
6
4
Clevis（2mm)
4
4
Screw (2x10mm)
8
Screw (3x5mm)
Locknut (2mm )
2
4
Washer(2x5mm)
Horn 2
4
8
Washer(3x6mm)
Pin hinge(24x24mm)
L bracket
Push rod （2mm)
TP Screw (2.3x12mm)
8
TP Screw (3x16mm)
8
Screw (3x16mm)
Secure the servo.Install the nylon control horn
and connect the linkage.
Assemble the servo tray to the wing with screws
and epoxy the ber horn to the aileron.
Epoxy the pin hinges to the slots in the ap.
Epoxy the aps to the wings as illustration.
Keep some space about 1mm width between
trailing edge and ap.
7
6
8
9
10
2
Accessory list for the coming installation steps.
2
Fiber deconations
1
scoop
1
Antenna
Cut o the surplus part from the PVC canopy, glue the berglass
pic to the PVC canopy and trim o the surplus part.
Fiberglass
PVC
PVC
Fiberglass
A
BC
3
Screw (3x20mm)
2
Scale gun set
Mount the fuel tank, battery and receiver to
the fuselage.
Assemble the antenna to the fuselage with screw.
8
TP Screw (2.3x8mm)
1
Canopy (Fiberglass)
1
Canopy (PVC)
Blind Nut
Battery
Fuel supply line
Fuel spray line
Air pressure line
Assembly of the fuel tank(please notice that the plug of
the tank and the tube should special for gasoline.
Fix the ply sheet as illustration with screw from the
fuselage to stop the battery from moverable.
1
Screw (4x15mm)
Screw (4x15mm)
1
Ply(3mm)
Ply(3mm)
Screw (3x20mm)
1
Screw (3x20mm)
1
Antenna
Antenna
56 58
59
11
57
55
Accessory list for the coming installation steps.

Wooden Block
2
Wooden Block
2
Wooden Block
2
Wooden Block
Screw
Using scotch tape, one side of it xed, cover the blind nut hole and mark
where the blind nut holes are.put the cowl to it is place on the fuselage,
base on the marks on the scoth tape drill holes to the cowling.
Reinforce the engine mount by epoxy the wooden
blocks to the engine mounts from inner and outer of
the engine mount as illustration.
Install the engine to the engine mount with screws.
Customer can also use electric motor as optional, the assemble
process is from step 52 to step 55. The side view when motor
install completion.
Remove the rewall o from the engine mount as
illustration.
Epoxy the optional box to the engine mount and put the
battery to the box from the hatch on the fuselage.
1
2
3
5
Screw (3x10mm)
5
Washer(3x6mm)
3mm
Battery
163mm
1
Optional box for motor
50
51
53
54
10
49 52
Install the L brackets to the servo of ap as
illustration below.
Assemble the servo tray to the wing with screws and
epoxy the ber horn to the ap.
Secure the servo.Install the nylon control horn
and connect the linkage.
4
Main wing joiner(20x420mm) 8
TP Screw (2.3x12mm)
Gear door
TP Screw (3x20mm)
Retracts strut
Wooden Block
Note:rubber wheels oleo struts
and retracts are optional.
1
2
1
1
2
8
Circlip
stainless steel rod
4
Wooden Block
Circlip
2
Retracts strut
circuit board
Oleo struts
TP Screw (2.3x12mm)
8
TP Screw (2.3x12mm)
1.5mm
2
Screw (6x50mm)
Masking tape
Main wheels (100mm)
Main wheels (100mm)
Screw (3x16mm)
8
TP Screw (3x16mm)
Mount the gear door and the wheel to the retract.
Ball joint
Ball joint
Lock Nut (2mm )
Lock Nut (2mm )
Washer(2x5mm)
Washer(2x5mm)
Screw (2x10mm)
Screw (2x10mm)
4
4
Screw (2x10mm)
Nut (2mm )
4
Washer(2x5mm)
Horn 2
Install the nylon control horn and connect the linkage.
L bracket 4
Screw (3x5mm) 8
8
Washer(3x5mm)
Washer (3x6mm)
Screw (3x5mm)
L bracket
Push rod （2mm)
12
13
11
15
3
14
Accessory list for the coming installation steps.

Main wing joiner(20x420mm)
TP Screw (3x20mm)
TP Screw (3x20mm) 8
8
TP Screw (2.3x12mm)
TP Screw (2.3x12mm)
Assemble the retracts to the appropriate position
in the gear house.
Connect the two wings through the main wing joiners.
The sketch map of the wing ts well to the fuselage.
Drag the servo line and retracts lines from the wing.
4
Main wing joiner(20x420mm)
Factory already set blind nuts in the wings, the customers can
x the wing to the fuselage by tightening the nylon screws.
2
Screw (6x50mm)
Screw (6x50mm)
B'
AA'
B
Make sure to glue securely.
If not properly glued, a failure in ight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming o during ights,
you'll lose control of your airplane which leads
to accidents!
A=A'
B=B'
The sketch map should be when the stabilizer
assembly completion.
17
18
20
21
4
16 19
1
Linkage Stopper 2
Plastic tube (2x650mm)
Fuel tank (550cc) 1
2
Wooden Block
2
Wooden Block
2
Wooden Block
5
Screw (3x10mm)
5
Washer(3x6mm)
1
Screw (4x15mm) 1
Ply sheet (3mm)
Tail wheel servo
Rudder servo
Rudder servo
TP Screw (2.3x8mm)
1.5mm
4
TP Screw (2.3x8mm)
163mm
The sketch map of the steel wires working in
the fuselage.
The sketch map of the steel wires connection out
of the fuselage.
Take o the tail wheel and trim a slot on the tail
cover for assembling the tail wheel. The side view when the engine install completion.
Assemble the tail gear cover with screws as below.
45
44
46
47
9
48
Accessory list for the coming installation steps.

Tail wheel (45mm)
Collar
Screw (2.6x12mm) 3
Screw (2.6x12mm)
Steel wire (0.5x3000mm)
Steel wire
Copper joiner
Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
Steel wire
Copper joiner
Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
Aluminum tube
Install the servo.
4
4
Clevis
Copper joiner
4
4
Screw (2x10mm)
4
Washer(2x5mm)
4
Steel wire (0.5x3000mm)
4
Aluminum tube
2
2
Clevis
Copper joiner
2
2
Screw (2x10mm)
2
Washer(2x5mm)
2
Steel wire (0.5x3000mm)
2
Aluminum tube
Alu clevis Locknut (2mm )
Locknut (2mm )
The sketch map when assemble the tail landing
gear to the wheel steeling mount.
The sketch map of the tail wheel and steel wires
working in the fuselage.
Fix the tail gear to the tail fuselage.
Assemble the steel wires well to the rudder horn
and tail wheel.
Connect the steel wires of the rudder horn and
tail gear to the servo.
39
41
42
43
8
40
38
2
carbon ber tube(10x285mm)
1mm
Tailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Elevator
Apply instant type AB glue to elevator and hinges.
Keep some space about 1mm width between
elevator and tailing edge.
Securely glue together. If coming o during ights, you 'll
lose control of your airplane which leads to accidents!
Epoxy the elevator to the stabilizer.
Fix the carbon ber tube to one side of the stab
with screws.
Glue the wooden block to each side of the stab tube as below, put the stab
tube into one side the horizontal to the end and mark it out at the root of
the horizontal, drill a hole in the stab tube and horizontal as illustration.
Make sure hinges are
mounted in the same line.
5mm 5mm
15mm 15mm
1.5mm
Screw (2.6x12mm) 1
1
Washer(3x10mm)
3mm
Screw (2.6x12mm)
Washer(3x10mm)
Screw (2.6x12mm) 2
2
Washer(3x10mm)
9
carbon ber tube(10x285mm)
Horn 4
pivot & round hinge(5x68mm)
6
pivot & round hinge(5x68mm)
22
24
23
25
5
26
Accessory list for the coming installation steps.

B'
AA'
B
Make sure to glue securely.
If not properly glued, a failure in ight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming o during ights,
you'll lose control of your airplane which leads
to accidents!
A=A'
B=B'
Screw (2.6x12mm)
Washer(3x10mm)
1.5mm
Screw (2.6x12mm) 1
1
Washer(3x10mm)
3mm
Make sure hinges are
mounted in the same line.
3
Securely glue together. If coming o during ights, you 'll
lose control of your airplane which leads to accidents!
Horn 4
pivot & round hinge(5x68mm)
The sketch map should be when the stabilizer
assembly completion.
Assemble the stab to the fuselage drill a hole to
the other section stab.
Fix the other side of the stab with screw.
Epoxy the pivot & round hinges to the rudder.
Epoxy the rudder to the vertical n.
Epoxy the ber horns to the slots in the rudder
and elevator.
27
28
29
30
32
6
31
8
Clevis(2mm)
Lock Nut (2mm )
Screw (2x10mm) Washer(2x5mm)
2
2
Screw (2x10mm)
2
Washer(2x5mm)
1
EVA(10mm)
EVA(10mm)
1
EVA(10mm)
Assemble the servos.
The sketch map of the push rod connect to the
elevator servo.
Assemble the push rod branches to the horns on
the elevator.
Assemble the another side of the push rod to the
elevator servo in the fuselage as image.
The sketch map of the push rod working in the fuselage.
Linkage Stopper
Washer (2mm)
Washer (2mm)
Nut (2mm)
Nut (2mm)
Set screw (3x4mm)
Set screw (3x4mm)
1
1
1
1
4
Steel wire (0.5x3000mm)
8
8
8
8
Copper joiner
Screw (2x10mm)
Washer(2x5mm)
1
Push rod
Set screw (3x4mm)
Washer (
2mm )
Nut (2mm)
8
Aluminum tube
Linkage Stopper 1
3
TP Screw (2.6x12mm )
4
TP Screw (2.3x8mm)
1
Tail wheel (45mm)
1
Tail gear
1
Alu clevis
2mm Rod
Adjustable Rod
Adjustable Rod
Lock Nut (2mm )
Screw (2x10mm)
Washer(2x5mm)
Push rod
Locknut (2mm )
Locknut (2mm )
34
35
36
37
7
33
Accessory list for the coming installation steps.