Harbor Mate OMC-F85 User manual

General Guidelines
• It is the user’s responsibility to read and follow all instructions.
•Keep these instructions with the product at all times and review before each use.
• It is the responsibility of this product’s owner to furnish the instructions to any person that borrows or
purchases the product.
•Inspect the product before use to ensure it is assembled properly and all parts are in safe working order
and free of defects.
•Never modify this product in any way.
•All circumstances cannot be addressed in these instructions. Please use common sense and prac-tice
general safety measures when using this product.
•Do not use this product for any purpose other than that for which it is intended.
•Parts and/or instructions are subject to change without notice.
• It is the user’s responsibility to read and follow all instructions.
•Keep these instructions with the product at all times and review before each use.
• It is the responsibility of this product’s owner to furnish the instructions to any person that borrows or
purchases the product.
•Inspect the product before use to ensure it is assembled properly and all parts are in safe working order
and free of defects.
•Never modify this product in any way.
•All circumstances cannot be addressed in these instructions. Please use common sense and practice
general safety measures when using this product.
•Parts and/or instructions are subject to change without notice.
Rev. 072020 1-888-651-3431 Page 1

Safe Installation
•Read all safety information and instructions before you install or use this product. Failure to follow Safety &
Use Instructions will void the warranty, and may result in injury, property damage, or death.
•Check that all hardware is properly tightened before use.
•Lubricate the wheels periodically.
•Never exceed the 85 lb. weight limit.
•This carrier is designed for moving motors short distances, for storage, and while performing maintenance.
•Do not use for anything other than its intended purpose.
•Securely chock the wheels while in storage or working on a motor mounted on the motor carrier.
•When storing a motor, it is recommended to securely chock the wheels and position it against a wall with
the handle facing outward.
•Never leave a motor and/or motor carrier unattended. Do not use on uneven ground.
•Keep away from children.
•Never run the motor while on the stand.
•Never tow the carrier behind any kind of vehicle.
•When carrying any heavy motor and positioning it on the carrier, it is recommended to use two people.
Tools Required
•Wrench
•Hammer
•Philips-head screwdriver
Rev. 072020 1-888-651-3431 Page 2

Diagram &Parts
Part
Description
Qty
Part
Description
Qty
A
Handle Tube
1
I
M6x65mm Bolt
2
B
U-Tube
1
J
M6x40mm Bolt
4
C
Connector
2
K
Turn Knob M8*40mm
2
D
Wheel
2
L
Φ6*18mm Washer
8
E
Axle
1
M
Φ6*12mm Washer
14
F
Vertical Straight Tube
2
N
M6 Lock Nut
10
G
Wood
1
O
M12 Lock Nut
2
H
M6x75mm Bolt
4
P
Φ12 Washer
4
Outboard Motor Weight Reference Chart
This chart has been created as a reference for determining the weight of your outboard motor. The weight
between a 2-stroke and 4-stroke outboard motor can vary significantly. These weights are only estimates that
are to be used for determining what size outboard motor carrier you should purchase. Before placing your
outboard motor onto the motor carrier, it is highly recommended to refer to the owner’s manual you received
with your outboard motor for the exact weight. If the manufacturer’s listed weight exceeds the rated weight
capacity of the motor carrier, do not try to mount - serious injury or damage may result.
Rev. 072020 1-888-651-3431 Page 3

Assembly
Note: First assemble all parts finger tight, then tighten all parts with a wrench when assembly is complete.
Step 1. Pass the Axle (E) through Vertical Straight Tube (F) and U-Tube (B), and fix Connector (C) on Vertical
Straight Tube (F) and U-Tube (B) with M6x40mm Bolt (J), Φ6*12mm Washer (M) and M6 Lock Nut (N).
Step 2. Fix the Wood (G) to Vertical Straight Tube (F) with M6x75mm Bolt (H), Φ6*18mm Washer (L) and M6
Lock Nut (N).
Rev. 072020 1-888-651-3431 Page 4

Step 3. Fix the Handle Tube (A) to Vertical Straight Tube (F) with M6x65mm Bolt (I), Φ6*12mm Washer (m) and
M6 Lock Nut (N). Screw Turn Knob M8*40mm (K) into Handle Tube (A) and connect Vertical Straight Tube (F).
Step 4. Insert M6x75mm Bolt (H) into Axle (E) and install Wheel (D). Insert Axle (E) and screw on M12 Lock Nut
(O).
Note: after the wheel is installed on the bracket, pay attention to the rolling of the bracket.
READ and FULLY UNDERSTAND ALL INSTRUCTION AND WARNING prior to using this Motor Stand. YOUR
SAFETY IS MOST IMPROTANT: Failure to comply with procedures and safeguards may result in serious injury
or property damage.
Rev. 072020 1-888-651-3431 Page 5

Product Warranty and Liability
GENERAL PRODUCT WARRANTY: Products purchased from the Authorized Dealer (original place of purchase)
or Merchant (“Dealer”) will be free of defects in material and workmanship at the time of receipt, and will
meet the specifications stated at the place of purchase transaction or online at the Dealer’s website, under
normal use and service when correctly installed, operated and maintained. This product warranty is effective
for the period of time stated below, unless otherwise stated in the product instructions or depicted in the
product advertisement. All Authorized Dealer warranties are NON-TRANSFERABLE and cover only the
original end purchaser. This limited warranty does not cover products purchased through non-authorized
dealers. Non-authorized dealer receipts are not accepted for warranty verification.
***Warranty claims must be made directly to the original place of purchase.***
WARRANTY PERIOD: This warranty remains in force for one year from the date of the product’s accepted
delivery. The Authorized Dealer offers a one year manufacturer’s warranty for most products unless otherwise
specified on the product advertisement.
WARRANTY SERVICE: The Authorized Dealer will replace any defective or malfunctioning part at no charge,
including payment of the shipping costs of parts or replacement product to and from the manufacturer. The
purchaser is responsible for labor charges. If the product does not meet specifica-tions as depicted in the
advertisement, the Authorized Dealer will refund the full purchase price of the product.
Questions regarding the warranty on a specific product and warranty claims should be directed to the
Authorized Dealer with whom the purchase transaction was made.
WARRANTY LIMITATIONS: The above warranty does not apply to products that are repaired, modi-fied or
altered by any party other than the Authorized Dealer; are subjected to unusual physical stress or conditions
(such as overloaded ramps or corrosion), natural disaster, governmental actions, wars, strikes, labor disputes,
riots, theft, vandalism, terrorism or any reason beyond reasonable control; are damaged due to improper
installation, misuse, abuse, accident or negligence in use, storage, trans-portation or handling, or tampering;
or to products that are considered consumable items or items requiring repair or replacement due to normal
wear and tear.
Product should be inspected prior to signing for delivery. Product damage incurred during shipping, unless
noted on the Bill of Lading at the time of delivery, renders this warranty void.
LIMITED LIABILITY: In no event shall THE AUTHORIZED DEALER be liable to the purchaser or any third party for
any indirect, incidental, consequential, special, exemplary or punitive damages arising out of the use of the
product, including, without limitation, property damage, loss of value of the prod-uct or any third party
products that are used in or with the product, or loss of use of the product or any third party products that
are used in or with the product.
Rev. 072020 1-888-651-3431 Page 6