Incy Interiors Georgia U034-1 User manual

1
Georgia Crib
USA Item #’s: U034-1, U034-2
Australian Item #’s: 1515-1, 1515-2
*Shown with mattress (sold separately)
Made in Vietnam for:
Incy Interiors Pty Ltd
2a Piper Street, Bathurst, NSW, 2795
AUSTRALIA
1300 94 20 50
www.incyinteriors.com.au
Designed and Distributed in Australia by:
Incy Interiors Pty Ltd
2a Piper Street, Bathurst, NSW, 2795
AUSTRALIA
1300 94 20 50
www.incyinteriors.com.au

2
UNITED STATES CRIB SAFETY WARNINGS
IMPORTANT
FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH
Read all instructions before assembling crib. Keep instructions for future use.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child’s
neck, such as hood strings or pacifier cords.
DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
Stop using crib when child is able to climb out or reaches the height of 35 in. (89 cm).
Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing
parts, or sharp edges before and after assembly and frequently during use. Securely tighten
loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken.
Contact Incy Interiors Pty Ltd for replacement parts and instructional literature if needed. DO
NOT substitute parts.
If refinishing, use a non-toxic finish specified for children’s products.
Follow warnings on all products in a crib.
CAUTION: ANY MATTRESS USED IN
THIS CRIB MUST BE AT LEAST 27-5/8INCHES
BY 52 INCHES WITH ATHICKNESS NOT
EXCEEDING 6 INCHES.

3
CANADIAN REGULATIONS
AFTER CRIB HAS BEEN COMPLETELY ASSEMBLED, STORE
INSTRUCTION SHEET IN THIS POUCH.
Do not use this crib if you cannot exactly follow the accompanying instructions.
Do not use this crib for a child who can climb out of it or who is taller than 90 cm.
Do not place in or near this crib any cord, strap or similar item that could become wrapped
around a childʼs neck.
Do not place this crib near a window or a patio door where a child could reach the cord of a
blind or curtain and be strangled.
Ensure that the sides of this crib are properly latched or locked in the appropriate position
when a child is left unattended in it.
Check this crib regularly before using it and do not use it if any parts are loose or missing or if
there are any signs of damage. Do not substitute parts. Contact Incy Interiors Pty Ltd if
replacement parts or additional instructions are needed.
Use a crib mattress that is no thicker than 15cm and is of such a size that, when it is
pushed firmly against any side of the crib, it does not leave a gap of more than 3cm between
the mattress and any part of the sides of the crib.
Children can suffocate on soft bedding. Do not place pillows, comforters or soft mattresses in
this crib.

4
AUSTRALIAN STANDARDS COMPLIANCE
WARNING: TO PREVENT FALLS THEMATTRESS BASE
OF THIS COT SHOULDBE ADJUSTED TO THE LOWEST
POSITIONBEFORE THE CHILD CAN SIT UP
RECOMMENDED MATTRESS SIZE: 700 MM
WIDE X 1320 MM LONG X NO MORE THAN
100 MM THICK
Failure to follow these warnings and the assembly instructions could result in serious injury or
death.
Before each usage or assembly, inspect cot for damaged hardware,
Loose joints, missing parts or sharp edges. Do not use cot if any parts are missing or broken.
Ask your dealer or contact Incy Interiors Pty Ltd for replacement parts and instructional
literature if needed. Do not substitute parts.
When child is able to climb out or reach the height of 90 cm, the cot shall no longer be used.
Do not place cot near window where cords from blinds or drapes may strangle the child.
If refinishing, use a non-toxic finish specified for children’s products.
Do not use a water mattress with this cot
Upon completion of assembly, be sure all screws and bolts have been tightened securely.
A periodic check should be made of all screws and bolts and retightened if necessary.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
Do not drag cot.
After cot has been completely assembled, store instruction sheet in the envelope provided on
the base of the crib.
Under no circumstances should this warning be removed from mattress support!
WARNING: TO PREVENT FALLS, THE
MAXIMUM MATTRESS THICKNESS SHOULD
NOT EXCEED 100 MM.

5
IMPORTANT SAFETY INFORMATION FOR TODDLER
& DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION
HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could resulting serious injury or
death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
The mattress intended for use on the bed shall be a full-size crib mattress having minimum
dimensions of 51-5/8 inches (1310mm) in length, 27-1/4inches (690mm) in width and 4 inches
(100 mm) in thickness, not exceeding 6 inches (152 mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s) provided must be used
to avoid the formation of a gap between the mattress and the bed that could cause an
entrapment.
DO NOT place bed near windows where cords from blinds or drapes may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child’s neck, such as hood strings
or pacifier cords.
DO NOT suspend strings over a toddler bed for any pacifier cords.
A child using the toddler or day bed shall be at least 15 months of age and shall not weigh
more than 50lbs (22.7kgs).

6
Care & Maintenance
When cleaning your crib, use a non-toxic, non-abrasive cleaner. Mix a solution of water with a
small amount of a mild detergent. Apply to crib surface with a damp cloth.
When moving the crib without castors assembled, always lifts the unit. Do not push or drag it
to avoid damaging the base.
It is important that the humidity levels in the room be controlled from extremes of too much
humidity or too little. The crib should not be placed directly next to air-conditioning, outlets,
fire places, radiators, space heaters, humidifiers, or dehumidifiers. Exposure to extreme
variations of temperature and humidity can damage wood products.
Keep the crib out of direct sunlight. UV rays may fade colours and in some cases darken them.
It can cause crazing or hair line cracks in the finish. White finishes will darken naturally over
time and exposure to direct sunlight will hasten this natural process along with some wood
darkening; this is not considered to be a quality defect.
If you need to put your crib in storage for any period of time do not store it in a damp or hot
environment. Allow air flow around the furniture and do not stack anything on it.
Check List
Always check the crib is free from damage before use. Do not use product if any damage is
present.
Regularly check that all assembly fittings are always tightened properly and retighten as
necessary.
After Sales Customer Service
When you receive your Incy Interiors product, if you need any assistance or if you have any
comments with respect to any aspect of the goods, please contact your local distributor via email.
If you are missing parts you can order parts by writing to the address below or call
888 –623 –5044. Please include the product name, colour, and a brief description of the part you
are missing.
You can also visit our website at www.incyinteriors.com for latest product information.
For service is United States:
Incy Interiors Pty Ltd
C/- ATC International
859 East Sepulveda Blvd
Carson, CA 90745 USA
Ph 888 –623 –5044
www.incyinteriors.com
For service in Australia:
Incy Interiors Pty Ltd
2a Piper Street, Bathurst, NSW, 2795
AUSTRALIA
1300 94 20 50
www.incyinteriors.com.au

7
Parts list

8
Hardware list

9
Assembly Instructions –Crib
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen off a turn. After crib is
completely assembled, return to each bolt and tighten.
1. Stand both headboards (ends) of the crib (part B) upright, and screw in side (part A2) with 4 x
bolts, 4 x spring washers and 4 x washers using the allen key provided.

10
2. Once side is attached, slide in the side rail (part A3)
3. Secure the side rail with 2x bolts, 2 x spring washers and 2 x washers with the allen key

11
4. Insert 8 x metal dowels into both sides of the crib mattress base (Part C) –4 x metal dowels per
side.
5. Ensure the warning labels are facing upward and align the mattress base with holes for the
required height. (Level 1 –upper level, Level 2 –lower level)

12
6. Insert the wooden dowel into the holes for the level that is not being used
7. Secure the remaining side rail with 4 x bolts, 4 x spring washers and 4 x washers with the allen key

13
8. Screw feet x 4 into the bottom the crib
9. Ensure all bolts are tightened before use.

14
Assembly Instructions –Toddler Bed
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen off a turn. After toddler bed is
completely assembled, return to each bolt and tighten.
1. Ensure mattress base (part C) is on level 2 - lower level (refer to crib instructions above)
2. Remove the side rail (part A2) by removing the 2 x bolts, 2 x spring washers and 2 x washers with
the allen key provided

15
3. Slide side rail out by lifting it up.