Instant Desks STYLE IDA-5006 User manual

ASSEMBLY INSTRUCTIONS
CHAIR STYLE RTA-5006
PARTS LIST
ATTENTION: Before you begin to assemble the
product, please make sure that all the parts are
included in the package and in good condition
ATTENTION:
Follow the instructions step by step.
To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.
Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
Using the wrong size of screws on a part could result in damage to the screw or the part.
E1
E2
F
CB
D
B
I
Insert the casters (F) in the legs of
the base (C) using pressure, then
place the gas lift (E1) in the middle of the
base and cover it with (E2) as shown.
Flip over the seat (B) with its back end
towards you and assemble the
armrests (G) in the respective sides using
screws (I) for the exterior holes and screws
(J) for the interior holes as shown.
Assemble the backrest (A) to the seat (B) using screws (K).
Using screws (H), assemble the
mechanism (D) to the seat (B) with its
handle facing to the LEFT as shown.
Place the top parts over the base parts making sure the tip of
the gas lift enters into the hole of the mechanism.
(Armrests;
exterior holes)
(Backrest)
Before seating and using the chair for the first time,
make sure that all screws are properly tightened.
A
When you seat on the
chair, not looking at it.
(Mechanism)
G (Right)
H
I
J (interior only)
G (Left)
(exterior)
(exterior)
B
K
Seat
B
x1
A
x1
Backrest
Star Base
C
x1
Mechanism
D
x1
Hydraulic
Gas Lift
E1
x1
Covers for
Gas Lift (Set)
E2
x1
Casters
F
x5
Armrest
G
M8x25mm
H
x4
M6x25mm
I
x4
M6x30mm
J
x4
M8x55mm
K
x4
Allen wrench
L
x1
x1
Right
x1
Left
(Armrests;
interior holes)
IDA-5006

CHAIR’S FUNCTIONS:
(1) Chair height: Pull UP the lever that is under the seat. The chair goes down while sitting on it,
or up if you lift your body.
(2) Chair tilting: Pull the same lever OUT horizontally to unlock this function. While unlocked,
the chair will tilt freely. When the chair is in the normal position, push the lever IN to lock
the tilting function.
(3) Tilting tension: Turn the mechanism’s knob in either direction to apply more or less tension.
(1)/(2)
(3)
WARNINGS:
•Do not stand up on the chair or use it as ladder.
•Use the chair to seat only one person at a time.
•Do not use the chair if parts are damaged or if screws are loose or missing.
•Do not seat near the edge of the seat and always sit properly on the chair to avoid going beyond your balance point and fall off the chair.
•The chair is intended for teenagers and adults. If small children are using the chair, please keep close observation on them.
•Do not allow small children to play with the chair.
•Not paying attention to these warnings could result in severe injuries.
CUCARE AND MAINTENANCE:
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are tighten.