Interlogix TruVision TVW-DVM User manual

© 2015 United Technologies Corporation. All rights reserved. P/N 1073093-EN • REV A • ISS 30SEP15
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.
TruVision Wedge Dome Back Box and Dual
View Mount Installation Guide
Product overview
This is the installation guide for the following TruVision wedge
camera models:
TVW-DVM (dual view mount) (use with TVD-PPB)
TVW-AWB-1 (angled back box for outdoor application)
TVW-AWB-2 (angled back box for indoor application)
TVW-2G-AD (Adapter plate for wedge camera with 2-gang
box)
Product and package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
TVW-DVM dual view mount
The TVW-DVM dual view mount (purchased separately) allows
you to install two panoramic cameras on a single mount. You
then obtain a view of the surrounding area without requiring a
complex integration effort when connecting to your storage
device or video management system (VMS).
Camera mount:
Tube adapter (30 x 12 mm): Conduit cover/plug:
Template A: Template B:
Screw 3 x 10 m (5 pcs m):
Screw (10 pcs):
Drywall anchor 7.5 x 24.5 mm
M4 screw 4 x 25 mm
Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm (5 pcs):
Rubber ring:
Figure 1: Cameras attached using the dual view mount
TVW-AWB-1 outdoor angled back box
The TVW-AWB-1 outdoor angled back box (purchased
separately) is weather resistant and includes a G1 threaded
conduit access and plug. It conceals the interconnect cables
and eliminates the blind area below the camera when the
camera is installed on a wall.

2 / 5 P/N 1073093-EN • REV A • ISS 30SEP15
Camera back box:
Tube adapter (30 x 12 mm): Conduit cover/plug:
Template A
:
Rubber ring:
Screw (5 pcs):
Drywall anchor 7.5 x 24.5 mm
M4 screw 4 x 25mm
Screw 3 x 10 mm (5 pcs):
Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm (3 pcs):
Figure 2: Camera mounted on an outdoor back box
TVW-AWB-2 indoor angled back box
The TVW-AWB-2 indoor angled back box (purchased
separately) conceals the interconnected cables and eliminates
the blind area below the camera when the camera is installed
on a wall.
Camera back box:
Template B:
Screw 5 pcs:
Drywall anchor (7.5 x 24.5 mm)
M4 screw (4 x 25 mm)
Screw 3 pcs (4 x 10 mm):
Figure 3: Camera mounted on an indoor back box
TVW-2G-AD adapter plate
The TVW-2G-AD adapter plate (purchased separately) allows
you to attach the panoramic wedge camera to a standard 4-
inch 2 gang box.
Camera adapter plate:
Template A:
Rubber ring:

P/N 1073093-EN • REV A • ISS 30SEP15 3 / 5
Screw 5 pcs:
Drywall anchor (7.5 x 24.5 mm)
M4 screw (4 x 25 mm)
Screw 3 x 8 mm (2 pcs):
Screw 4 x 10 mm (3 pcs):
Figure 4: Wedge camera attached to a 2 gang box
Installation
To mount two wedge cameras on a dual view mount:
1. Attach the TVW-DVM dual view mount to an installed
pendant mount tube. An adapter is included in the kit that,
if required, can be used to match-up with the threading
(G1 male or G1 female) of the pendant mount tube.
2. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.
3. Pull the cables through the bracket tube and to both back
boxes, conect the cables to cameras and place the
connecters and cables into the back boxes.
4. Mount the two cameras on both sides of the TVW-DVM
dual view mount.
5. Re-attach the camera covers to the cameras.
To mount the wedge camera on an outdoor angled back
box:
1. Drill the holes for the mounting hardware in the mounting
surface using the supplied drill template.
2. Detach the TVW-2G-AD adaptor plate from the back box.
3. Mount the TVW-2G-AD adaptor plate to the mounting
surface using the supplied hardware.

4/ 5 P/N 1073093-EN • REV A • ISS 30SEP15
4. Mount the outdoor angled back box to the TVW-2G-AD
adaptor plate using the supplied hardware.
5. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.
6. Connect the cables, conceal the cables and connectors
inside the back box and mount the camera base to the
outdoor angled back box.
7. Re-attach the dome cover to the camera.
To mount the wedge camera on an indoor angled back
box:
1. Drill the holes for the mounting hardware in the mounting
surface using the supplied drill template.
2. Mount the indoor back box to the mounting surface by
using the supplied hardware.
3. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.
4. Connect the cables, conceal the cables and connectors
inside the back box, and mount the camera base to the
indoor angled back box.
5. Re-attach the dome cover to the camera.
To mount the wedge camera on a 2-gang box:
1. Install the 2-gang box (separately purchased) in the wall
according to the local applicable codes and regulations
2. Attach the TVW-2G-AD adapter to a pre-installed 2-gang
box on wall.

P/N 1073093-EN • REV A • ISS 30SEP15 5 / 5
3. Attach the enclosed rubber ring to the 2-gang box adapter.
4. Loosen the screws with the tamper-resistant hex wrench
(supplied) to remove the camera cover.
5. Connect the cables, conceal the cables and connectors
inside the 2-gang box and mount the camera base to the
2-gang box adapter.
6. Re-attach the camera cover to the camera.
Specifications
TruVision wedge camera bracket and
mount
TVW
-DVM
Dimensions (L × W × H)
134.2 ×131.2 ×86.2 mm
(5.28 × 5.16 × 3.9 in.)
Weight
422 g (0.93 lb.)
T
VW-AWB-1
Dimensions (L × W × H)
134.1 ×130.9 ×54 mm
(5.27 × 5.15 × 2.12 in.)
Weight
321 g (0.71 lb.)
TVW-AWB-2
Dimensions (L × W × H)
133.9 ×130 ×32.2 mm
(5.27 × 5.12 × 1.26 in.)
Weight
101 g (0.22 lb.)
TVW
-2G-AD
Dimensions (L × W × H)
134.1 ×130 ×13.5 mm
(5.27 × 5.12 × 0.53 in.)
Weight
129 g (0.28 lb.)
Regulatory information
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.