Itc T-6707 User manual

OWNER'S MANUAL

NETWORK AUDIO ADAPTER

IP NETWORK PUBLIC ADDRESS SYSTEM

Please follow the instructions in this manual to obtain the optimum results from this unit.

We also recommend that you keep this manual handy for future reference.

T-6707

OFF

VOL

SET

ADDRESS

POWER

10W

MIC

VOL

30W

20W

NETWORK

POWER

AUX 1

GND

AUX 2

CH 2

SPK PUT

AUX

IN PUT

LAN IN TERMINAL

~230V 50Hz 75W

T1AL 250V

T-6707

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS .....................................................................1

2. GENERAL DESCRIPTION ....................................................................3

3.FEATURES........................................................................................3

4.NOMENCLATUREAND FUNCTIONS.......................................................4

5.OPERATION ................................................ .....................................5

6.CONNECTION DIAGRAM .....................................................................7

7.SCHEMATICDIAGRAM........................................................................8

8.SPECIFICATIONS...............................................................................9

Be sure to read the instructions in this section carefully before use.

Make sure to observe the instructions in this manual as the conventions of safety symbols and messages

regarded as very important precautions are included.

We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property

damage which could result from mishandling. Before operating your product, read this manual first and

understand the safety symbols and messages so you are thoroughly aware of the potential safety

Indicates a potentially hazardous situation which, if mishandled, could

result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

When the Unit is in Use

Should the following irregularity be found during

use, immediately switch off the power, disconnect

the power supply plug from the AC outlet and

contact your nearest dealer. Make no further

attempt to operate the unit in this condition as this

may cause fire or electric shock.

If you detect smoke or a strange smell coming

from the unit.

If water or any metallic object gets into the unit

If the unit falls, or the unit case breaks

If the power supply cord is damaged (exposure of

the core, disconnection, etc.)

If it is malfunctioning (no tone sounds.)

To prevent a fire or electric shock, never open nor

remove the unit case as there are high voltage

components inside the unit. Refer all servicing to

your nearest dealer.

ITC

Do not place cups, bowls, or other containers of

liquid or metallic objects on top of the unit. If they

accidentally spill into the unit, this may cause a fire

or electric shock.

Do not insert nor drop metallic objects or

flammable materials in the ventilation slots of the

unit's cover, as this may result in fire or electric

shock.

When Installing the Unit

Do not expose the unit to rain or an environment

where it may be splashed by water or other liquids,

as doing so may result in fire or electric shock.

Use the unit only with the voltage specified on the

unit. Using a voltage higher than that which is

specified may result in fire or electric shock.

Do not cut, kink, otherwise damage nor modify the

power supply cord. In addition, avoid using the

power cord in close proximity to heaters, and never

place heavy objects -- including the unit itself -- on

the power cord, as doing so may result in fire or

electric shock.

Be sure to replace the unit's terminal cover after

connection completion. Because high voltage is

applied to the speaker terminals, never touch these

terminals to avoid electric shock.

Be sure to ground to the safety ground (earth)

terminal to avoid electric shock. Never ground to a

gas pipe as a catastrophic disaster may result.

Avoid installing or mounting the unit in unstable

locations, such as on a rickety table or a slanted

surface. Doing so may result in the unit falling

down, causing personal injury and/or property

damage.

1. SAFETY PRECAUTIONS

An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in

the electrical installation of the building.

When the Unit is in Use

Do not place heavy objects on the unit as this may

cause it to fall or break which may result in

personal injury and/or property damage. In

addition, the object itself may fall off and cause

injury and/or damage.

Make sure that the volume control is set to

minimum position before power is switched on.

Loud noise produced at high volume when power is

switched on can impair hearing.

Do not operate the unit for an extended period of

time with the sound distorting. This is an indication

of a malfunction, which in turn can cause heat to

generate and result in a fire.

Contact your dealer as to the cleaning. If dust

is allowed to accumulate in the unit over a long

period of time, a fire or damage to the unit may

result.

ITC

If dust accumulates on the power supply plug or in

the wall AC outlet, a fire may result. Clean it

periodically. In addition, insert the plug in the wall

outlet securely.

Switch off the power, and unplug the power supply

plug from the AC outlet for safety purposes when

cleaning or leaving the unit unused for 10 days or

more. Doing otherwise may cause a fire or electric

shock.

When Installing the Unit

Never plug in nor remove the power supply plug

with wet hands, as doing so may cause electric

shock.

When unplugging the power supply cord, be sure

to grasp the power supply plug; never pull on the

cord itself. Operating the unit with a damaged

power supply cord may cause a fire or electric

shock.

When moving the unit, be sure to remove its power

supply cord from the wall outlet. Moving the unit

with the power cord connected to the outlet may

cause damage to the power cord, resulting in fire or

electric shock. When removing the power cord, be

sure to hold its plug to pull.

Do not block the ventilation slots in the unit's cover.

Doing so may cause heat to build up inside the unit

and result in fire.

Avoid installing the unit in humid or dusty locations,

in locations exposed to the direct sunlight, near the

heaters, or in locations generating sooty smoke or

steam as doing otherwise may result in fire or

electric shock.

SAFETY PRECAUTIONS

1. Integrated design, integrated network decoding module, digital power amplifier, and speakers

3. Built on demand acquisition module, the realization of real-time signal acquisition function

4. upport stereo line input and volume adjustment functions

5. Support network volume

6. The power output, outside enlarge 8 /30 w speaker constant resistance

7. Can be connected to the Ethernet front-end ports, across network segment and routing

8. ddress reset function

9. ith a microphone input and volume adjustment functions

Built-in hi-fi speakers, stereo power amplifier 8 2X30W

3. FEATURES

2. GENERAL DESCRIPTION

IP network active speakers with high efficiency, small volume, light weight, good, simple, and

the sound Canon, practical advantages, can be widely used in the meeting place, home, enter

-tainment, professional performance Such as amplification area, has the good market prospect.

FRONT

1. Connect the Ethernet /

switch port (RJ45 interface)

2. Serial line interface, the connection

can be set to address code

3. Powerswitch

4. AC power input

5. Loudspeaker output, external deputy

speaker

6. S

7. AUX volume potentiometer

tereo line input

8. MIC 6.3 single input

9. MIC volume potentiometer

10.Network potentiometer

11.Address code reset buttons, press 9 seconds

long this button, then press 3 times in a row,

can restore the factory IP address

12.Power indicator light

13.Deputy box input end, connecting the main

output terminal box on the horn

NOMENCLATUREAND FUNCTIONS

RATED PWR:20W

MAX PWR :40W

IMPEDANCE : 8

OFF

VOL

SET

ADDRESS

POWER

10W

MIC

VOL

30W

20W

NETWORK

POWER

AUX 1

GND

AUX 2

CH 2

SPK PUT

AUX

IN PUT

LAN IN TERMINAL

~230V 50Hz 75W

T1AL 250V

T-6707

12 13

5. OPERATION

Click Inquire

Diagram 1 Diagram 2

Diagram 3 Diagram 4

Diagram 5 Diagram 6

After click CONFIRM, change the connection mode to be network, write the same IP in address

bar as Diagram 5, click INQUIRE. After inquiry, then the window as diagram 6 appear. The

terminal configure is ok.

1.Connect the TERMINAL and computer's TERMINAL with serial port line or change to USB connector,

open All Program from Start in computer, find INTELLIGENT NETWORK BROADCAST then

choose TERMINAL CONFIGURE PROGRAM 2.36, run software program , open terminal configure

window 1, in serial port mode, click INQUIRY, then there will be window 2.

After inquire(whether configure terminal), confirm IPaddress correct or not, write the IP Address

(Eg.192.168.1.100), the window as diagram 3 appear. After confirm the IP address,click write,after

writing and confirm it is correct, then the window as diagram 4 appear (terminal configure wil get

the physical address MAC automatically).

2.IP network PAsystem configure:

OPERATION

In Terminal Configure, set one IP call code to be paging center, press paging key, then it can

realize telecom communication between two terminals.

Diagram 7

Note the power switch

1. Power switch: (1) switch up to play, power on;

(2) switch to play down, power off;

2.Power switch for the single pole switch, switch off state,the device does not

completely disconnect the power grid, unused equipment must unplug the power plug.

OFF

~220V 50Hz

T1AL 250V

VOL

SET

ADDRESS

POWER

10W

MIC

VOL

30W

20W

NETWORK

POWER

CH 1

GND

CH 2

SPK PUT

AUX

IN PUT

LAN IN TERMINAL

Connection box

Connect the Ethernet /switch port

OPEN

PLAY STOP NEXTPREVIOUS

OFF

POWER

CD / TUNER /MP3 players and other

audio equipment

6.CONNECTION DIAGRAM

7. SCHEMATIC DIAGRAM

MONITOR SPEAKERS

Network decoding

Ethernet port

The adapter

Power supply to the

network board

To the front end circuit

power supply

POWER

AMPLIFIER

MONITOR SPEAKERS

Network Input

Protocol Support

Audio Format

Sampling Rate

Transmit Speed

Audio Format

Frequency Output

T.H.D

Standard RJ45 1,3 Input, 2 output ( need insert the switcher)

TCP/IP UDP IGMP (group broadcasting)

S.N

Power Consumption

Dimension

Power Supply

N.W

MP3/MP2

8K-48KHz

10Mbps

16 digit stereo CD tone

20Hz~16KHz

0.3%

>70dB

75W

~220-240V 50-60Hz

245X185X215mm

6Kg

Output impedance and

power rating 8 /30W Lndustry standard terminal blocks

Working temperature 5 ~40

Working Humidity 20%~80%RH,condersation

8. SPECIFICATIONS

Address reset function Address code reset buttons

IP NETWORK PUBLIC ADDRESS SYSTEM

VersionV0.3

Table of contents

ITC T-6707 User manual