J.Burrows DELANEY JBDELAMBBK User manual

This chair has a load rating of 160kg
Page 1
Assembly Instructions
DELANEY CHAIR
JBDELAMBBK

ABC D
X1 X1 X2 X1
X1 X1 X1 X5
E F G H
I (5/16’’x1’’) J (5/16’’x1-2/5”) K (1/4’’x1-1/5”) LM (5mm)
X2 X2 X6 X1 X1
HARDWARE LIST
Please check you have all hardware components before assembling.
If you are missing any hardware components please contact My Zone on
Tel: [phone] or Email: [email protected]
Please ensure you have the name of the item, store purchased from, hardware part required and quantity.
Please retain your receipt to validate warranty. Enjoy your new purchase!
Page 2

Step 1
Step 2
FRONT
Page 3
H
G
E
F
B
C
K
Note:Turn the Star Base (G) upside down and insert 5 Casters (H) into the holes on the base.
Turn the Star Base (G) over and insert Gas Lift (E) with Telescopic Cover (F) through
the center hole on top of the Star Base (G).
Note: Align the Armrests (C-L/C-R) on the bottom of the Seat Cushion (B) .
Tighten the screws.
Torque
5 Nm
M

FRONT
Step 3
Step 4
Page 4
B
D
I
J
D
Note: Attach the Seat Plate (D) to the bottom of the Seat Cushion (B) (with the
front of the seat plate facing the front of seat cushion).
Tighten the screws.
E
Note: Place assembled seat on the Gas lift (E) . Push down firmly until connection is secure.
Torque
6 Nm
M
Torque
6 Nm
M

Step 5
Step 6
Page 5
L
Note: Check to make sure the knob on the rear right side of the Seat
Plate (D) is loose before this step.
Align Back Cushion (A) with Seat Cushion (B) by GENTLY inserting
back support plate into the rear hole of the Seat Plate (D) as shown
and TIGHTEN by using the knob on the rear right side of the Seat
Plate (D).
Note: Insert Plastic Stopper (L) into the back support plate as shown.
D
A
B

Step 7
Page 6
Your Delaney Chair is now complete and ready for use.
IMPORTANT NOTE:Periodically check and re-tighten screws.
Officeworks Superstores Pty Ltd 236-262 East Boundary Road East Bentleigh 3165 Australia

*
- To increase chair height pull
lever upward while lifting body
weight slightly off the seat.
- Release leaver at desired height.
- To lower chair height sit fully into
the chair and pull lever upward.
- Release leaver at desired height.
* Back Tilt
Move your upper body fore and
aft to a comfortable position.
When comfortable lock the position
by pushing the lever down.
*
Chair Tilt
* Back Height Adjustment
- Loosen knob on rear of backrest
by turning anti-clockwise.
With both hands raise or lower the
backrest to desired height and
re-tighten knob by turning colckwise.
*
Pull lever up whilst moving the
arm up or down. Release lever
at desired height.
ARM
HEIGHT
BACK
HEIGHT
BACK
TILT
GAS-LIFT
HEIGHT
- Sitting in the chair pull lever up.
Chair Height Adjustment
Your feet should be resting flat
on the floor.
- Sitting in the chair pull
lever up.
Move you body to a comfortable
position.Lock the position by
pushing the lever down.
Arm Height Adjust
DELANEY CHAIR
FEATURES
Page 7
CHAIR TILT
WARNING: please fully tighten the bolt after you have completed assembly