Jancy Engineering Slugger USA5 User manual

Slugger®USA5
Slugger
®
Portable Magnetic Drilling Machine
OPERATOR’S MANUAL
HEARING PROTECTION
REQUIRED
EYE PROTECTION
REQUIRED
MODEL #18066 (120V) OR #18080 (220V)
Serial # Date of Purchase
BEWARE OF
ROTATING
MACHINE PARTS
LINE VOLTAGE
PRESENT
NEVER PLACE
FINGERS NEAR
CUTTING AREA OR
MACHINE ARBOR
WARNING!
before use, be sure everyone using this machine reads and understands
all safety and operating instructions in this manual.
United States Patent #5,415,503 other patents pending.

Slugger
®
Portable Magnetic Drilling Machine
Congratulations on your purchase of a Slugger® portable magnetic drilling machine. Slugger® drilling machines are
designed to deliver fast, efficient hole drilling performance in portable applications. Please take a moment to complete
and mail your product warranty registration card. Doing so will validate your machine’s warranty period and ensure
prompt service if needed. Thank you for selecting a Slugger® product from Jancy Engineering Inc.™
table of contents
Important Safety Instructions ...................................3-4
Special Instructions ......................................... 5
Grounding Instructions, Extension Cords, Guideline For Shift Lever Position .... 6
Contents Of Package ....................................... 7
Getting Started, Before You Drill ................................ 7
Before The Cut, Ready To Cut, After The Cut........................ 8
Basic Troubleshooting ....................................... 9
Regular Maintenance ...................................... 10
Control Panel And Parts List .................................. 11
Machine And Arbor Breakdown ............................... 12
Machine And Arbor Parts Lists ................................ 13
Motor Breakdown And Parts List ............................... 14
Dimensions And Specifications ................................ 15
JANCY ENGINEERING RESERVES THE RIGHT TO MAKE
IMPROVEMENTS AND MODIFICATIONS TO DESIGN WITHOUT PRIOR NOTICE.
limited warranty
Jancy Engineering Inc.™will, within one (1) year from the original date of purchase, repair or replace any goods found
to be defective in materials or workmanship, provided the product warranty registration card has been returned to Jancy
Engineering Inc.™ within thirty (30) days of purchase date. This warranty is void if the item has been damaged by acci-
dent, neglect, improper service or other causes not arising out of defects in materials or workmanship. This warranty does
not apply to machines and/or components which have been altered, changed, or modified in any way, or subjected to
use beyond recommended capacities and specifications. Electrical components are subject to respective manufacturers’
warranties. All goods returned defective shall be returned prepaid freight to Jancy, which shall be the buyer’s sole and
exclusive remedy for defective goods. In no event shall Jancy Engineering be liable for loss or damage resulting directly or
indirectly from the use of merchandise or from any other cause. Jancy Engineering is not liable for any costs incurred on
such goods or consequential damages. No officer, employee or agent of Jancy is authorized to make oral representations
of fitness or to waive any of the foregoing terms of sale and none shall be binding on Jancy.
2
™

important safety instructions
WARNING!
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1. Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
d) Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to
operate tool.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) or
residual current device (RCD) protected supply. Use of a GFCI or RCD reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks,
non-skid safety shoes, hard hats or hearing protection used for appropriate conditions will reduce personal
injuries.
3

important safety instructions
4
c) Prevent unintentional starting. Ensure the switch is in the “OFF” position before connecting to power source
and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or key left attached to
a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any
adjustments, changing accessories or storing power tools. Such preventative safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool
or these instructions to operate power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tools etc. in accordance with these instructions, taking into account
the working conditions and the work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
h) Check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check alignment
of moving parts, binding of parts, breakage of parts, mounting and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized
service center.
5. Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

1. If you require an additional manual, please contact Jancy Engineering at [phone] for a FREE copy.
2. Never place hands, fingers, gloves or clothing near cutting area or rotating machine parts.
3. Always disconnect machine from power source before changing cutters, clearing chips, refilling lubricant or
performing adjustments.
4. Keep all safety features functioning and working properly.
5. Never wear loose clothing, gloves or jewelry when working near cutting area or rotating machine parts.
6. Always use eye and hearing protection.
7. Always use safety strap and chip guard provided with machine.
8. Always use proper tooling. Keep cutters securely fastened.
9. Do not use dull or broken cutters.
10. Do not use Slugger® drilling machines on surfaces or materials being welded. Doing so can damage the
machine’s electrical components.
11. Beware of slugs ejected at end of cut. They become HOT during the cut.
12. Magnet will not hold properly on thin materials or rough and dirty surfaces.
13. Keep bottom of magnet burr free and clear of chips and debris.
14. To reduce the risk of electrical shock, do not use machine in wet or damp areas.
15. Do not remove or alter electrical panels. Use only authorized service centers for repairs.
16. Motor will not start on non-ferrous materials.
WARNING!
do not operate machine if warning and/or instruction labels are missing or damaged.
contact jancy engineering for replacement labels.
special instructions
5

WARNING!
Improperly connecting the grounding wire can result in the risk of electrical shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with tool. Never remove the
grounding prong from the plug. If the cord or plug is damaged, have it repaired
before using. If the plug will not fit the outlet, have a proper outlet installed by a
qualified electrician. The USA5 must be plugged into an appropriate outlet, prop-
erly installed and grounded in accordance with all codes and ordinances. The
plug and outlet should look like those in Figure A.
WARNING!
do not use slugger® drilling machines on surfaces or materials being
welded. doing so can result in personal injury and/or damage to the
slugger® drilling machine.
grounding instructions
6
DRIP LOOP: To help prevent cutting fluids from traveling
along power cord and contacting power source, tie a drip
loop in power cord as shown in Figure B.
Fig. B
Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s
plug. Replace or repair damaged cords. Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. Jancy recommends using a minimum 12 gauge extension cord
not to exceed 100 feet. The table below is supplied only as a guide to minimum gauge for extension cords, where the
smaller the gauge number, the heavier the cord.
extension cords
minimum gauge for extension cords
volts total length of cord in feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
amperage
0-6 18 16 16 14
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 not recommended
recommended wire gauge
note: jancy recommends using aminimum 12 gauge
extension cord not to exceed 100 feet.
guideline for usa5 shift lever position

Remove all contents from packaging and inspect to ensure no damage was incurred during shipping. Your USA5 package
should also include the following:
contents of package
description part # qty
OPERATOR'S MANUAL LIT104 1
PRODUCT DVD LIT032 1
WARRANTY CARD 0070342 1
3/16" PILOT, 1" DEPTH OF CUT 16001 1
3/16" PILOT, 2" DEPTH OF CUT 16002 1
1/4" PILOT, 1" DEPTH OF CUT 16003 1
1/4" PILOT, 2" DEPTH OF CUT 16004 1
1/4" PILOT, 3" DEPTH OF CUT 16005 1
3/8-24 X 5/16" FPSSS UH1474 3
3/16" HEX WRENCH UH8013 1
3/16" T-HANDLE HEX WRENCH UH8014 1
4MM HEX WRENCH UH8002 1
SPOKE HANDLE 0151333 3
SAFETY STRAP U11005 1
PIPE HANDLE 0010224 1
PIPE HANDLE ADAPTER 0010225 1
MAGNET WARNING NOTICE 0107D0C 1
SHUNT (ATTACHED TO HANDLE) UH5335 1
SHUNT INSTRUCTIONS U14102 1
getting started
what you should know before you drill
CAUTION!
always disconnect usa5 from power source before making adjustments.
NOTE: The item numbers found below in parentheses refer to the images on page 12.
Assemble three spoke handles (item #18) to hub pinion shaft (item #17). NOTE: Feed hub assembly is mounted on
right side of machine frame. If necessary, it can be reversed for lefthand operation by simply removing the fastener (item
#29) and sleeve (item #30) from frame. Remove hub pinion shaft from right side of frame and insert it into left side of
frame. Replace sleeve and fastener into frame and tighten securely. Thread pipe handle (item #2) into motor housing.
The control panel (item #27) may also be reversed from left to right side of machine if desired. Remove screws (item
#19) holding control panel and side cover plate (item #20) next. Remove side cover plate and control panel, then
disconnect magnet and motor pin connections when removing control panel. Move control panel to opposite side of
frame. Reconnect magnet and motor pin connectors and secure control panel assembly using four screws (item #19).
Replace side cover plate, making sure warning instructions are visible.
1. Type of material to be drilled, Brinnell or Rockwell hardness, material thickness and position should all be determined
to ensure proper selection of Slugger® cutting tools, RPM, coolant and drilling time.
2. Remove any excessive mill scale or rust from surface to be drilled.
3. When drilling materials under 3/8" thick, an additional steel plate may be required to achieve proper magnet
adhesion.
4. Material that has been flame cut may have become heat-treated and therefore difficult to drill. Avoid drilling near
such areas whenever possible.
5. Drilling with the USA5 in horizontal positions requires a special lubrication for Slugger® cutters.
Consult Jancy Engineering for details.
7

1. Select correct pilot pin and place in cutter shank from the rear. Align flats on cutter shank with arbor body set screws.
Insert cutter in arbor body.
2. Tighten set screws securely on cutter shank flats. NOTE: Set screws should be recessed in arbor body when tight.
3. The surface you are working on should be clean, flat and free from rust, scale, dirt and chips.
4. Determine correct cutting speed for application. Move gear box shift lever by lifting outward then repositioning to
desired speed.
CAUTION!
never change gears with motor running. doing so can result in personal injury and/or damage to the machine.
5. Place Slugger® machine on workpiece with pilot pin over the center of hole to be drilled.
6. Connect machine to power source.
7. Lower Slugger® cutter to surface of material to be cut. Coolant will be released down the pilot into center of
Slugger® cutter. Coolant flow can be stopped by lifting pilot pin off work surface or by using coolant valve. NOTE:
Be sure coolant valve is open. Regulate coolant flow by adjusting coolant valve on left side of mainframe.
CAUTION!
always use safety strap. failure to do so could result in personal injury
and/or damage to the slugger® drilling machine.
8. The safety strap must be securely fastened to machine and around work being drilled. Loop strap around work piece
and connect strap ends by attaching to D-rings on drill. NOTE: Safety strap is intended only to restrain the drill to the
work piece in the event of a power failure to the magnetic base.
9. Position chip guard toward work area before drilling.
before the cut
ready to make the cut
CAUTION!
position chip guard toward work area before drilling.
1. Move magnet switch to “ON” position. Switch will illuminate to indicate power is present–magnetic base should be
firmly secured to workpiece at this time. Thin materials may require an additional steel plate to achieve proper
magnet adhesion.
2. Start drill motor by depressing green motor “ON” button.
3. Advance cutter into material using the feed handles until Slugger® cutter has established an external groove in the
material. During the remainder of cut apply smooth constant pressure without overloading motor. NOTE: Slugger®
cutters are designed for uninterrupted cutting. Chips are evacuated during the cut. Do not peck drill when using
Slugger® cutters.
CAUTION!
if drill motor should stall or stop before acomplete cut is made, always remove cutter from hole before
attempting to restart motor. failure to do so could result in personal injury and/or damage to the slugger® drilling
machine and cutter. note: this machine’scircuitry will automatically shut the drill motor off if magnetic base is sepa-
rated from its work surface. if your machine requires adjustment, contact jancy’sservice department.
1. After Slugger® cutter has finished the cut, the “slug”, or uncut center portion of material, will be expelled when
motor is returned to the full up position.
2. Return machine into full upright position and depress red motor “OFF” button, wait until motor completely stops.
3. Move magnet switch to “OFF” position when ready to release magnetic base from work surface.
after the cut
8

1. Magnetic base not holding securely
•Material is too thin to engage magnet.
•Surface of material being drilled must be free of chips, debris, rust and mill scale.
•Size of cutter exceeds machine’s rated capacity.
•Check magnet face for unevenness, nicks and burrs.
•Welding equipment connected to material being drilled.
2. Drill motor running, arbor and spindle not turning
•Possible sheared spindle key.
3. Motor slows when drilling
•If an extension cord is being used, see page 6 for recommended wire gauges and cord lengths.
•Excessive downfeed pressure during drilling cycle will cause motor to slow and overheat.
•Cutting tool needs to be resharpened.
4. Coolant system not working
•Coolant system is gravity dependent. Machine must be in an upright position to operate properly.
•Check operation of coolant valve. Valve must turn freely.
•Check coolant lines for blockage.
•Dirt or debris in coolant tank.
•Consistency of coolant mixture too thick.
•Incorrect pilot pin being used.
•Vent hole in coolant tank lid blocked.
5. Slugs not ejecting from cutter
•Lack of coolant causing slugs to expand in cutter bore.
•Incorrect pilot pin being used.
•Possible broken internal arbor parts.
6. Breaking cutters
•Coolant must be supplied to interior of cutter.
•Excessive feed pressure being applied when cutter initially contacts work surface.
•Confirm material hardness.
•Drilling stacked materials with incorrect cutter.
•Dull cutters; dull or chipped cutting edges require excessive feed pressure, resulting in breakage.
•Excessive arbor runout–see regular maintenance on page 10.
•Possible bent motor spindle or worn arbor sleeve.
•Improperly adjusted motor slide–see page 10.
7. Oversized or rough holes
•Insufficient coolant.
•Excessive feed pressure.
•Dull cutter.
•Worn support bracket roller bearing or arbor body sleeve.
•Bent motor spindle.
•Motor slide improperly adjusted.
basic troubleshooting
9

1. The motor slide may become loose and require adjustment after the machine has been in service. Refer to parts
breakdown and become familiar with the USA5 parts. Locate motor slide cover plate (item #31 on page 13)
and adjustment screw (item #8 on page 14). Using the 3 spoke feed handles, position motor and
slide assembly in the full up position. Insert supplied 5mm hex key through slide cover plate access hole. Using the
hex key turn adjustment screw (item #8) clockwise to increase slide tension or counter-clockwise to decrease slide
tension. Do not over tighten adjustment screw. Excessive slide tension can damage the USA5. Properly adjusted, the
motor and slide assembly should have no side to side movement and remain in position without drifting down.
2. Keep bottom of magnet clean, free of chips, burrs, nicks, oil and other contaminants. Inspect magnet face
to ensure surface is flat and square. A worn magnet surface dramatically reduces magnetic holding force.
3. Periodically lubricate motor slide ways with lithium base grease.
4. Routinely grease zerk (item #23) on arbor support bracket.
5. Visually inspect arbor, sleeve and support bracket for wear.
6. Arbor runout should not exceed .0035 inches per revolution. This is most accurately measured by placing a dial
indicator needle inside of arbor bore and rotating arbor while observing indicator.
7. Inspect coolant system, reservoir, o-rings, lip seals and coolant collar for wear.
8. Inspect motor brushes and replace as needed.
9. Replace any worn parts and regularly tighten fasteners that have become loose during usage.
10.Regularly test machine by placing machine on non-ferrous material. Engage magnet switch.
Motor should not start.
regular maintenance
10

control panel and parts list
11
item description part # qty
1 POWER CORD ASSEMBLY, 120V 0151550 1
POWER CORD ASSEMBLY, 220V 0151551
2 MOTOR ON/OFF SWITCH 0151035A 1
3 M4 NUT UH4604 1
4 M4 LOCK WASHER UH2046 1
5 M4 X 10 DSPHMS UH0418 1
6 M3 X 12 CRFHMS UH0316 4
7 CONTROL PANEL PLATE 0151057J 1
CONTROL PANEL OVERLAY, 120V 0151061 1
PANEL GASKET 0151227 1
CONTROL PANEL OVERLAY, 220V 0151062 1
8 MAGNET SWITCH, 120V 0151045 1
MAGNET SWITCH, 220V 0101044
9 WIRE LINE ASSEMBLY 0151552 1
10 NEUTRAL WIRE LINE ASSEMBLY 0151054 1
11 PC BOARD, 120V, 220V 04868 1
12 PANEL ENCLOSURE ASSEMBLY 0151051 1
12A MOTOR HARNESS 0151564 1
12B RS MAGNET HARNESS 0151563 1
13 SHUNT UH5335 2
14 CONTACT BLOCK SWITCH 0151033A 1
15 MOTOR SWITCH HARNESS 0151558 1
12B
10
11
12
15
13
12A
14
9
8
7
6
2
1
5
4
3
panel wiring diagram

machine and arbor breakdown
12
14
12
9
8
7
6
5
4
3
2
1
13
15
11
10
19
16
18
17
25
20
21
22
23
24
16
ARBOR ASSEMBLY (0151441)
A
1
3
4
18
17
16
15 14
13
6
8
10
9
11
2
38
12
20
21 22
11
12 23
19
27
14
15
30
29
31
32
35
19
34
36
33
7
5
39
26
25
24
37
28
23
B

machine and arbor parts lists
13
item description part # qty
1 MOTOR ASSEMBLY, 120V 04600R 1
MOTOR ASSEMBLY, 220V 04602R
2 PIPE HANDLE 0010224 1
3 CHIP GUARD ASSEMBLY 0151570 1
4 ARBOR ASSEMBLY 0151441 1
5 DRILL FRAME 04700R 1
6 1/4" ID X 5-1/4" TUBING UH6005 1
7 QUICK ELBOW COUPLER 0070034-N 1
8 QUICK PANEL BARB COUPLER 0151271 1
9 1/2" LOCK WASHER UH2530 1
10 QUICK COUPLING SPACER 0151309 1
11 M6 X 20 HHCS UH0636 4
12 1/4" LOCK WASHER UH2402 4
13 PINION GEAR U18000 1
14 NEEDLE BEARING UH3132 2
15 THRUST WASHER 0151205 2
16 WOODRUFF KEY 0010142 1
17 PINION HUB SHAFT 0151193U 1
18 SPOKE HANDLE 0151333 3
19 M3.5 X 10 CRPHMS-ETLW UH0323 8
20 COVER PLATE ASSEMBLY 0151305 1
21 MAGNET ASSEMBLY, 120V, 220V 0151180 1
22 SAFETY STRAP LINK U11004 1
23 3/16 " ID TUBE A=5", B=10" UH6011 1
24 SPIRAL KEY RING UH8022 1
25 6-32 X 1-1/8 CRFHMS UH1035 2
26 COOLANT VALVE KIT 0151170 1
27 CONTROL PANEL ASSYEMBLY, 120V 0151036 1
CONTROL PANEL ASSYEMBLY, 220V 0151037
28 COOLANT BOTTLE ASSEMBLY 0151289 1
COOLANT BOTTLE 0151163 1
COOLANT CAP 0151165 1
RUBBER WASHER 0151169 1
COOLANT STRAINER 0151174 1
29 M6 X 25 SHCS UH0648 1
30 BLACK GEAR SHAFT END CAP 0151195 1
31 SLIDE COVER PLATE 0151113 1
32 M5 X 12 CRFHMS UH0516 2
33 CORD CASE 0151451 1
34 M3 X 12 CRFHMS UH0316 2
35 MOTOR CORD ASSEMBLY 0151448 1
36 MOTOR COVER 0151111 1
37 M5 X 10 BHSCS UH0506 4
38 PIPE HANDLE ADAPTER 0010225 1
39 6-32 NUT UH4715 2
item description part # qty
1 INTERNAL RETAINING RING UH4119 1
2 STEEL WASHER UH2606 1
3 RUBBER WASHER UH2604 1
4 ARBOR PISTON 0151435 1
5 SPRING 0151431 1
6 ARBOR PLUNGER 0151433 1
7 3/8-24 X 5/16" FPSSS UH1474 2
8 ARBOR BODY 0151437 1
9 3/8-24 X 5/16" CPSSS UH1472 1
10 1/4-20 X 1" BHSCS UH1432 1
11 PISTON SPACER 0151512 1
12 SPIRALOC RETAINING RING UH4044 2
13 O-RING UH6350 2
14 COOLANT INDUCER U22002 1
15 M6 X 16 BHSCS UH0616 2
16 1/4" LOCK WASHER UH2402 4
17 BRASS BARB FITTING UH6100 1
18 RETAINER PLATE U21002 1
19 ARBOR SLEEVE 0151439 1
20 INTERNAL RETAINING RING UH4153 1
21 THRUST WASHER 0151207 1
22 NEEDLE BEARING UH3208 1
23 GREASE FITTING UH6600 1
24 M6 X 20 HHCS UH0636 2
25 ARBOR BEARING BRKT. ASSY. 0151015 1
ARBOR PARTS LIST
MACHINE PARTS LIST

14
motor breakdown and parts list
item description part # qty
1 INTERNAL RETAINING RING UH4152 1
2 MOTOR SPINDLE 04522 1
3 WOODRUFF KEY 0010142 1
4 BALL BEARING UH3057 1
5 EXTERNAL RETAINING RING UH4025 1
6 SPINDLE SEAL 04594 1
7 LOWER GEARBOX 04530S 1
8 M6 X 25 SHFCS UH0652 1
9 M8 X 40 HHCS UH0818 4
10 M8 LOCK WASHER UH2083 4
11 SLIDE BAR WEDGE 04511N 1
12 GEAR RACK U68002 1
13 M6 X 10 LHSCS UH0606 3
14 3/16" X 5/8" DOWEL PIN UH4311 1
15 BALL BEARING UH3035 2
16 OUTPUT GEAR 04581 1
17 EXTERNAL RETAINING RING UH4019 1
18 BALL BEARING UH3024 1
19 PINION GEARSHAFT 04520 1
20 WOODRUFF KEY 04564 1
21 HELICAL INPUT GEAR 04582 1
22 BALL BEARING UH3024 2
23 CLUSTER GEAR 04580 1
24 OUTPUT PINION GEAR SHAFT 04521 1
25 KEY 04565 1
26 SHIFTING FORK 04510 1
27 MAIN SPEED SELECTOR PIN 04523 1
28 SPEED SELECTOR LEVER 04534 1
29 ROLL PIN UH4205 1
30 SPEED SELECTOR SPRING 04591 1
31 SPEED SELECTOR PIN 04524 1
32 M5 LOCK WASHER UH2056 1
33 M5 X 35 SHCS UH0558 1
34 SHIFT LEVER LABEL 04514 1
35 M3 X 5 CRPHMS UH0300 2
36 GEARBOX GASKET 04593 1
37 GEARBOX COVER 04531 1
38 BALL BEARING UH3039 1
39 ARMATURE FAN 04590 1
40 ARMATURE, 120V 04553 1
ARMATURE, 220V 04554
41 BALL BEARING UH3021 1
42 UPPER ARMATURE SPRING WASHER 04560 1
43 M4 X 60 SHCS UH0438 2
43A CABLE CLAMP 04585 1
44 M4 LOCK WASHER UH2046 2
45 FIELD SCREW INSULATOR 04557 4
46 FIELD, 120V 04555 1
FIELD, 220V 04556
47 FIELD SLEEVE INSULATOR 04558 1
48 MOTOR HOUSING 04532 1
49 BRUSH HOLDER 04551 2
50 2 MOTOR BRUSHES WITH CAPS 04550 1
51 MOTOR SNAP BUSHING 04559 1
52 M5 X 5 CPSSS UH0500 2
53 MOTOR TAG, 120V 04512 1
MOTOR TAG, 220V 04513
54 DRIVE SCREW UH1002 2
55 END CAP 04533 1
56 M5 LOCK WASHER UH2056 4
57 M5 X 60 SHCS UH0562 4
58 M3 X 6 SHCS UH0302 2
59 DANGER LABEL 0080027 1
60 BRUSH LEAD INSULATOR 04578 2
61 CORD CHANNEL 0151453 1
- 14 OZ. GREASE 04587 1
usa5 motor assembly
04600r - 120 Volt
04602r - 220 Volt

15
dimensions and specifications
DIMENSIONS AND SPECIFICATIONS
Max Height 23-5/8" (600mm)
Min Height 20”(508mm)
Width 7-1/2" (191mm)
Length 11-9/16" (294mm)
Weight 51 lbs. (23Kg)
Motor 1.8HP 1400W (single phase)
120V /11.7A~220V /5.8A
310/610 RPM (no load) -180/340 RPM (load)
Arbor bore 3/4" (19.05mm)
Drill point breakaway 950 lbs. on (1" plate 431Kgon25mm plate)
Magnet base dimensions 4" x7-1/2"(102mmx191mm)
Magnet dead lift 2320 lbs. on 1" plate (1053Kgon25mm plate)
Slugger cutter diameter (maximum) 2-3/8" (60mm)
Slugger depth of cut (maximum) 3" (76mm)
Spindle CL to Guard Face 2-1/8" (54mm)
Spindle CL to Magnet Face 1-3/4"(44mm)
Spindle CL to Motor Face 2-1/8" (54mm)
Total travel 3-5/8" (92mm)
7-1/2"
191
1-3/4"
44
1-1/4"
32
9-7/16"
240
2-1/8"
54
13-3/8"
340
23-5/8"
(UP)
600
3-7/8"
98
5-1/8"
130
4"
102
2-1/8"
54
15"
381
7-1/2"
191 3/8"
10
20"
(DOWN)
508

your distributor
Tel · 563.391.1300 or Fax · 563.391.2323
2735 Hickory Grove Road · Davenport, Iowa 52804
email · [e-mail] / web · jancy.com
LIT104H
©Jancy Engineering Inc.™ 01/11
other available slugger®drills
Trusted. Tested. Tough.™
description model # max diameter depth capacity
USA101 120V USA101 1-1/2" 2"
USA101 220V USA101-2 1-1/2" 2"
USA200 120V HOLEMAKER II 1-3/8" 2"
USA200 220V HOLEMAKER II 1-3/8" 2"
2 X 2 120V 17980 2" 2"
2 X 2 220V 17982 2" 2"
4 X 4 120V 17985 4" 3"
4 X 4 220V 17987 4" 3"
MAGFORCE 120V 06920 1-5/8" 2"
MAGFORCE 220V 06921 1-5/8" 2"