JumpSport Elite 14ft Trampoline System User manual

1
JumpSport, Inc.
1680 Dell Ave
Campbell, CA 95008 USA Patent info at: Patents.JumpSport.com
408-213-2551
www.jumpsport.com
Retain address information for future use.
14ft JumpSport Elite Trampoline System
User’s Manual
Assembly, Installation, Care, Maintenance, and Use Instructions
WARNING
Read these materials prior to assembling and using this
trampoline and Trampoline Enclosure
DO NOT attempt or allow
somersaults. Landing on the
head or neck can cause serious
injury, paralysis or death, even
when landing in the middle of the
bed.
DO NOT allow more than one
person on the trampoline. DO
NOT allow more than one
person inside the trampoline
enclosure. Use by more than
one person at the same time
is not recommended.
Use trampoline only with mature, knowledgeable supervision.
DO NOT attempt to jump over
the enclosure system.
DO NOT intentionally rebound
off the enclosure system.
The maximum user weight is 240 pounds. This
trampoline is not recommended for use by children
Save Time! Watch Install Videos for Tips, Shortcuts, and Updates at
www.JumpSport.com/Installation-Videos
Instruction Manual P/N: INS-P-11600-03D
JumpSport Elite 14ft Trampoline System P/N: UNE-U-11597-03

2
Copyright Notice
This material is protected by United States copyright laws and is proprietary to JumpSport, Inc. Disclosure, reproduction, translation,
modification, or use of this document by anyone other than authorized employees, authorized users, or licensees of JumpSport
without the prior written consent of JumpSport, Inc. is prohibited.
The information in this document is subject to change without notice. JumpSport, Inc. shall not be liable for any damages resulting
from technical errors or omissions, which may be present in this document, or from use of this document.
Copyright © 2009-2016, by JumpSport, Inc. All rights reserved.
Trademarks
JumpSport®, JumpSport Elite™, Sure-Lok™, ProFlex™ Basketball Set, Game and Party Pak™, SureStep™ Trampoline Ladder, and
BounceBoard Extreme™ are trademarks of JumpSport, Inc.
All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.
Patents
This product includes technology associated with one or more of the following U.S. Patents:
No. 6,053,845
No. 6,261,207
No. 6,840,891
No. 6,846,271
No. 7,060,001
Additional Patents Pending.
Patent info at: Patents.JumpSport.com
How to Contact Customer Support
Should you require customer service or technical support for your JumpSport Elite 14ft Trampoline System, please contact Jump-
Sport’s Customer Service department at:
408-213-2551
6:00am—5:00pm Monday through Friday, Pacific Time

3
Contents
Chapter 1 Introduction 5
JumpSport ProFlex Basketball Set 6
Game and Party Pak 6
Chapter 2 Assembly and Installation Instructions 7
Preparation 7
Trampoline Placement 7
Tools (Trampoline) 8
Parts List (Trampoline) 8
Tools (Safety Enclosure) 9
Parts List (Safety Enclosure) 9
Assembly 11
Final Steps 26
Disassembly 27
Chapter 3 Care and Maintenance Instructions 29
Inspection (Trampoline & Safety Enclosure) 29
Trampoline Mat 30
Cold Weather Protection 30
Replacement Parts 30
Disassembly 30
Care and Maintenance Safety Checklist (Trampoline) 31
Care and Maintenance Safety Checklist (Safety Enclosure) 33
Windy Conditions 34
Moving the Trampoline 34
Care 34
Chapter 4 Warning Information 35
Points of Safety 35
Before you Jump 35
Landing on Springs or Frame 36
Bouncing off the Trampoline 36
Landing Incorrectly on the Mat 36
Chapter 5 Use Instructions 37
Safety Rules (Trampoline) 37
Safety Rules (Safety Enclosure) 38
Basic Skills 39
Bouncing 39
Stop Bounce 39
Arm Action 39
Bounce Variations 40
Basic Landing Positions 40
Seat Drop 40
Hands and Knees Drop 41
Front Drop 41
Series of Drops 42

4
Assembly and Installation
Preparation
Before you begin assembling your JumpSport Elite 14ft Trampoline System, make sure your trampoline is in a proper
location.
Trampoline Placement
CAUTION: When deciding on where to place your trampoline, consider the following:
WARNING
Overhead Clearance Adequate overhead clearance is essential. A minimum of 24 feet from ground level
is recommended. Provide clearance for wires, tree limbs, and other possible hazards.
Lateral Clearance Lateral clearance is essential. Place the trampoline and trampoline enclosure away from
walls, structures, fences, and other play areas. Maintain a clear space on all sides of the
trampoline and trampoline enclosure.
Level Surface Place the trampoline and trampoline enclosure on a level surface before use.
Lighting Use the trampoline and trampoline enclosure in a well-lighted area. Artificial
illumination may be required for indoor or shady areas.
Security Secure the trampoline and trampoline enclosure against unauthorized and
unsupervised use.
Ground Clearance Remove any obstructions from beneath the trampoline and trampoline enclosure.
Note: The trampoline enclosure is only to be used as an enclosure for a trampoline and the trampoline must be of
the appropriate size as covered by the specific enclosure.
Note: The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in
the Use Instructions.
IMPORTANT: The best surface on which to place your trampoline is dirt or grass. However, if you plan to install the
trampoline on a very hard surface such as concrete or asphalt, a dense foam —similar to what can be found in
public playgrounds —should be installed under each leg. Contact JumpSport Customer Service if you have any
questions.
It is the responsibility of the purchaser to become familiar with all of the information in this booklet, to
convey the warnings to all users, and to enforce JumpSport’s rules for safe use.
This unit is not intended for commercial or public use, and such use is strictly prohibited.
The maximum user weight is up to 240 pounds.
This trampoline is not recommended for use by children under six years of age.

5
Windy Conditions
It is possible for the trampoline to be blown about by a high wind. If you anticipate high winds, the frame should be
secured to the ground with the use of a JumpSport Trampoline Anchor Kit. If you anticipate severe winds, the
trampoline should be moved to a sheltered location or completely disassembled. Our anchor kit can be found in the
Accessories section at www.jumpsport.com.
Moving the Trampoline
If you need to move your trampoline periodically, it should be moved by at least two people and kept horizontal during
the move. Stand together holding on to one section of the rail and lift one side of the trampoline. Rotate that end of the
trampoline about five feet, then go to the opposite end of the trampoline, and do the same thing. This will slowly rotate
each end of the trampoline toward your desired destination, and is the easiest way to move the trampoline due to its
heavy weight. Disassemble the trampoline for any move greater than a few feet.
Care
Do not allow family pets on the trampoline, as claws may snag and pull the trampoline mat material or net material, or
damage the frame pad or pole foam.
The 14ft Elite Trampoline System is intended to be used by one person at a time, weighing less than 240 pounds. The
user should either be barefoot or wearing gymnastic slippers or non-cleated athletic shoes. The user should remove all
sharp objects from their person that may cause injury or damage to the trampoline mat. Heavy, sharp, or hard pointed
objects should not contact the mat surface.
Diagram 2 JumpSport Trampoline Anchor Kit
Use a JumpSport Trampoline Anchor Kit to tie
down your 14ft Elite Trampoline System.
(Photo is for illustration only and may not match
actual product)
Trampoline Placement
WARNING: Do Not use or stand near the trampoline in
windy or gusty conditions. A trampoline can become air-
borne when exposed to sustained wind or gusting wind
conditions. This can result in serious injury, paralysis, or death,
as well as property damage. To reduce these risks, disassemble
the trampoline and enclosure and store them until weather con-
ditions improve. Anchoring a trampoline frame may prevent the
trampoline from moving as a result of the wind, but even an-
chored trampolines can become airborne or damaged. Consult a
qualified contractor to determine what type of anchor works
best in your location.

6
Assembly and Installation Instructions
Tools Installation of the safety enclosure requires a 13mm hex wrench (included) or a deep socket with a ratchet or
cordless drill, and a 5mm Allen wrench (included). An 8 foot A-Frame ladder will be useful for some steps (use care
and follow procedures for use). Safety glasses and gloves are also recommended for safety.
Parts List (Safety Enclosure)
Your 14ft Elite Trampoline System is shipped with the parts shown below. The safety enclosure parts ship in a separate
box, which has a smaller box inside of it. If any parts are missing, immediately call JumpSport Customer Service at 408-
213-2551.
Note: Do NOT discard the foam tubing (Reference #13 and #14); it is needed to make the pole assemblies. It is not
just packing material. Not all poles will have foam around them. And do NOT remove any caps from the ends of any
of the support poles.
Nylock nut (Ref. #16d)
Acorn nut (Ref. #16e)
Reference # Part # Description Quantity
10 POL-A-11401-02 Lower support pole, with snap-button 8
11 POL-P-11497-02 Upper support pole, notch at one end 8
12 CAP-P-21441-00 Pole cap, black slotted 8
13 FOA-P-10078 Long foam tubing (1 tube packed over 1 pole) 8
14 FOA-P-10103 Short foam tubing (2 tubes packed over 1 pole) 8
15 SLE-P-11607-01 Pole sleeve, blue vinyl 8
16a BOL-P-10081 M8 bolt, Allen head 16
16b SPA-P-10083 Pole spacer, black 16
16c WAS-P-10082 Washer 32
16d NUT-P-10084 M8 Nylock nut 16
16e NUT-P-10622 M8 acorn nut, capped end, black 16
17 TOO-P-10158 Wrench, 13mm hex 1
18 TOO-P-10159 Wrench, 5mm Allen 1
19 NET-P-21342-00 41ft x 6ft heavy-duty rectangular mesh net 1
20 STR-P-11150
Short strap with buckle (approximately 2 feet long)
(8 come pre-assembled to top of net) 16
21 CAP-P-21441-00 End Cap, Enclosure Poles, Slotted 8
22 STR-P-11157 Long strap with buckle (approximately 3 feet long) 8
23 BUN-P-10110
Bungee t-anchor
(both come pre-assembled to bottom of net) 2
Parts List (Trampoline)
Your 14ft Elite Trampoline System is shipped with the parts shown below. The trampoline parts ship in 2 separate box-
es which may arrive on different days. If any parts are missing, immediately call JumpSport Customer Service at 408-213
-2551.
Reference # Part # Description Quantity
1LEG-A-11797-01 Horizontal leg piece 4
2LEG-P-11796-01 Vertical leg piece 8
3RAI-P-11795-01 Rail piece with 2 leg sockets, 12 spring notches 4
4RAI-P-11794-01 Rail piece with no leg sockets, 12 spring notches 4
5MAT-A-11592-02 Mat, 96 V-rings 1
6SPR-P-10059 Spring, 8.5 inches 96
7a PAD-A-11801 Frame pad section 8
7b PAD-P-11752 Pad connector, with Velcro (connects frame pad sections) 16

7
Assembly
Note: We recommend at least 2 people participate in assembling the trampoline. Use page 6 to help with part
names and numbers.
Assembly and Installation Instructions
1) Lay all rail and leg pieces in a circle as shown. See page 6 for
detailed part descriptions.
2) Using 1 horizontal leg piece and 2 vertical leg pieces, build a
leg assembly as shown above.
If applicable, snap buttons on ends of horizontal leg pieces will need to
be depressed before legs will fit together. See next page for leg
positioning.
4) Stand 1 leg assembly upright and connect a rail with 2 sockets
as shown.
3) IMPORTANT: The holes through the vertical legs—located
near the center of each vertical leg and not related to the snap
buttons—will be used for connecting the enclosure poles in a
later step. On one side, the hole will be flat and flush with the
leg. On the other side, the hole will be indented into the leg. You
can see and feel a difference between each side by running your
finger along the hole.
Both vertical leg pieces must have the indented side facing the
same direction. When you attach the leg assemblies to the rails
in the next steps, the indented side must face out and away
from the trampoline.
>> Repeat Step 2 with all remaining leg pieces. When finished,
you will have 4 complete leg assemblies. See next page for how to
properly align the leg assemblies.
Rail with 2
leg sockets
Ref. #3
Rail with no
leg sockets
Ref. #4
Horizontal
leg piece
Ref. #1
Vertical leg
piece
Ref. #2
(Top view)
Leg assembly
Holes in vertical leg pieces
must have indentations
facing the same direction
IMPORTANT: See next page for how to properly align
the leg assemblies.
CAUTION
Pinch point.
Pay careful attention to hand
position when connecting tubes
and handling springs.
Rail with 2
leg sockets
Ref. #3

8
Assembly and Installation Instructions
IMPORTANT: As you connect leg assemblies to rails, pay careful attention to snap buttons in horizontal legs. All snap buttons are designed to
point toward center of trampoline when properly installed. Indented holes in vertical legs need to be facing away from trampoline, and aligned with
holes in leg sockets of trampoline.
If the snap buttons in the horizontal legs are not pointing toward the middle of trampoline, flip the entire leg assembly around 180
degrees. Double-check the vertical leg pieces to insure the indented side is facing away from trampoline. If not, rotate each vertical
leg piece around 180 degrees.
(Top view showing whole
Correct Incorrect
(rotate leg assembly
(Top view showing whole
Leg assembly
Leg assembly
Hole in leg socket
of trampoline rail.
Hole in vertical leg
piece, shown with
indentation facing out.
All holes shown
correctly lined up with
each other.
Snap button
(Snap buttons in horizontal legs must
point toward center of trampoline.)
(Snap buttons in horizontal legs must
point toward center of trampoline.)

9
Assembly and Installation Instructions
5) Connect another leg assembly to same rail with 2 sockets. 6) Connect rail with no sockets, then rail with 2 sockets.
7) Connect next leg assembly to rail with 2 sockets.
>> Repeat Steps 6 and 7 all the way around until all rail pieces
and leg assemblies are connected together.
8) Completed frame.
Note: The frame may not be snug at this point. This is normal
until you start adding the mat and springs, which add tension to
the frame to help keep everything snug.
Rail with 2
leg sockets
Ref. #3
Rail with no
leg sockets
Ref. #4

10
TIP: For easy spring installation, connect spring to V-ring of mat
and pull toward you, to connect to frame. Use a second spring as
a tool to hook onto the one you are installing.
IMPORTANT: If you have a PowerBounce Trampoline, open the
separate PowerBounce box and use those instructions to install
the PowerBounce springs while you install the standard springs
in the following steps.
9) Connect jumping mat to trampoline frame using 4 springs.
Connect each spring to a V-ring and spring notch, approximately
1/4 circle apart from each other. Warning labels must face up.
Note: For this step, the springs do not have to be perfectly
spaced. They are to help keep tension on the mat temporarily
while you attach the remaining springs.
10) Start at a spring that is already connected. While standing
outside the frame, count 4 V-rings and spring notches clockwise,
and connect another spring. The easiest way to connect a spring
is to hook spring onto V-ring, then pull it toward you and hook it
into spring notch on top of frame rail.
11) Continue counting 4 V-rings and notches and connecting a
spring until you have gone all the way around the trampoline.
When you get to a spring that you connected in Step 9, reposition
it if necessary, so that the springs are all spaced exactly 4 V-rings
and spring notches apart.
V-rings
Spring
Ref. #6
Spring notches
Spring
Ref. #6
Spring
Ref. #6
(Top view)
(Top view)
(Top view)
Mat
Ref. #5
Warning label on
mat facing up
Warning label on
mat facing up
Assembly and Installation Instructions

11
12) Now connect a spring to every middle V-ring and spring notch, working clockwise around the trampoline. Have someone work
across from you, also going clockwise.
Note: It is important to have someone working across from you. Otherwise the springs could over-extend and become difficult to
connect, or possibly even damaged.
13) Connect all the remaining springs to the trampoline, working clockwise, with someone working across from you.
(Top view)
(Top view)
Person 2
Person 1
Assembly and Installation Instructions

12
15) Two pad connectors are used to connect adjacent pad sections together; one pad connector connects to the bottom of each pad
section and the second pad connector connects to the top of each pad section.
14) Lay the 8 frame pad sections on the trampoline to create a full circle around the trampoline frame. Align pad sections to line up
directly in-between each vertical leg. The button bungee t-anchor cords will hang down from the bottom of the pad (as shown on next
page).
Pad connector
Ref. #7b
Pad connector
Pad connector
WARNING: Trampoline use is not recommended without the frame pad in-
stalled (see Picture on page 20). The frame pad is designed to reduce the possi-
bility of injury by protecting the user from coming into contact with the frame and
springs of the trampoline. It is very important that you properly and securely attach the
frame pad to the frame, and that it is in the correct position prior to using the trampoline.
Assembly and Installation Instructions
End of pad sections
Vertical legs
Ref. #2
Frame pad section
Ref. #7a

13
16) Between the poles on the top of the frame pad, you will find a button bungee. Lift the pad at one of these button bungee
locations. The bungee on the bottom side of the pad will be used to secure the pad around the frame of the trampoline.
17) Secure button bungee t-anchor around frame of trampoline, as shown.
>> Repeat at every button bungee t-anchor until all 16 t-anchors are securely fastened to the frame of the trampoline.
Button bungee on
top of frame pad
Button bungee
t-anchor on bottom
of frame pad
Assembly and Installation Instructions
Frame of trampoline

14
18) Build all pole assemblies as shown. See page 6 for detailed part descriptions.
Bolt
Ref. #16a
Pole spacer
Ref. #16b
Acorn nut
Ref. #16e
Nylock nut
Ref. #16d
Washer
Ref. #16c
19) Using the tools and hardware provided, attach a pole to the outside of each trampoline leg. The holes on the bottom of the poles
will have a indentation on one side. Indentations must face the vertical leg. Tighten bolts and nylock nuts snugly with a wrench.
Hand-tighten acorn nuts.
Assembly and Installation Instructions
Steel Lower pole (Ref. #10)Steel Upper pole (Ref. #11)
Long foam tubing (Ref. #13)Short foam tubing (Ref. #14)
Vinyl Pole sleeve (Ref. #15)
Top of upper pole
Top of lower pole
(narrower end
with snap button)
Plastic Pole Cap
(Ref. #12)

15
Pole
Pole
Pole
Pole
Pole
Pole
Pole
Pole
Star
(Top view.
Leg assem-
blies shown
21) Identify where you want the door. It must be directly over a horizontal leg (example: pole 1 and pole 2 on the diagram above).
Assembly and Installation Instructions
Note: Entrance to trampoline
will be between poles 1 and 2.
(Top of net)
Red markers adjacent to door
Doorway
(overlapping panels)
(View from outside of net)
(Bottom of net)
Bottom corner of inside section of
net, secured to outside edge.
20) Familiarize yourself with the net.
 Find the top and bottom of the net. The top has overlapping panels of net sewn together. The bottom of the net has one obvious
corner.
 The outside of the net has a free-hanging bottom corner and will not be attached to anything. The inside corner will be secured to
an outside edge. A warning placard will also be attached to outside panel of net.
 You will start by attaching top of net all the way around. Then you will finish by attaching the bottom.
Bottom corner of
outside section
of net

16
22) On top of the net, find a red marker adjacent to the entryway. Install a short strap through the net at the top of the enclosure pole
at this location . Feed the free end through buckle so you have a generous loop, repeat, installing short straps at the remaining 7 red
marks.
The door must be over a horizontal leg with the proper side facing out (refer to diagram on page 15). Hang the short straps on either
side of the door into the slots of the enclosure pole caps. Hang the short straps on each enclosure pole. Do not tighten the short
straps.. Leave straps loosely connected for now.
IMPORTANT: To ease net adjustment and to prevent the buckle from being damaged, the buckle must be on the outside of the net.
The buckle must be in-between the pole and the net.
Assembly and Installation Instructions
1st
2nd
3rd
4th

17
24) On the bottom of the net, place a long strap with buckle through the pad’s grommet holes closest to Pole 2. Wrap a long strap
under the leg of the trampoline and secure loosely. Strap will be secured through buckle as shown above.
>> Repeat this step at remaining 7 poles. It is important to secure the straps loosely. The straps will be tightened in a later step.
1st
2nd
3rd
4th
25) The bottom of net directly between any 2 poles will have grommet holes. Push a short strap with buckle up through bottom and
then top pad connector grommets. Wrap short strap through grommet holes in bottom of net and then feed strap back down through
pad connector grommets.
Assembly and Installation Instructions
WARNING: If the buckle is upside-down and the strap is routed through it, the
strap will not hold. Aempt to pull the strap out of the buckle to be sure the
straps are secure. If the strap pulls free, ip the buckle over and reinstall the strap.

18
26) Wrap the end of the strap with a buckle over the top of the trampoline rail and secure it loosely through the buckle underneath the
rail. The frame pad may need to be lifted up for this step.
>> Repeat steps 25 and 26 clockwise all the way around the trampoline at the remaining 7 locations. It is important to loosely secure
the straps; they will be tightened in the another step
Assembly and Installation Instructions

19
1st
2nd
3rd
4th
Assembly and Installation Instructions
Completed
28) Pull the bottom corner of the net towards pole 2. Life the pad and secure the pre-installed button bungee T-Anchor found on the
bottom corner of the net. Secure the bungee around the frame between poles 1 and 2. The bungee secures around the frame the exact
same way as the T-anchors show on page 13.
29) Starting with the top straps, evenly tighten all of the straps. Tighten the straps at the bottom of the poles and then the straps in
the middle of each panel.

20
Assembly and Installation Instructions
Final Steps
Assembly is now complete! Make sure all parts are securely assembled. Before using your 14ft Elite Trampoline System,
familiarize yourself and all users with the Care and Maintenance Instructions, Warning Information, and Use Instructions
included in this manual.
To register your 14ft Elite Trampoline, visit our webpage at www.jumpsport.com and click on the Product Registration
link.
WARNING: Trampoline use is not recommended without the frame pad installed (see Picture A, below).
The frame pad is designed to reduce the possibility of injury by protecting the user from coming into
contact with the frame and springs of the trampoline. It is important to properly and securely attach the
frame pad the frame in the correct position prior to using the trampoline.
Frame Pad Placement - Showing Correct Placement over Frame Rails and Springs
(Section of frame pad removed for clarity. Be sure pad is completely installed before use.)
Picture A
Your trampoline is now complete!