kincrome K15320 Use and care manual

PEDESTAL DRILL PRESS
Operation and Safety Instructions
PART No. K15320

SECTION PAGE
I. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
II. General safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
III. Specific safety rules for bench drill presses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
IV. Electrical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
V. Know your bench drill press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
VI. Assembly and adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
VII. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
VIII. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
IX. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
X. Replacement parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Bench Drill Press with Laser Line
MOTOR: 220-240 V 50Hz
POWER:550W
SPEED:450–2500 RPM
CHUCKCAPACITY:1/8–5/8" (3–16 mm)
QUILL DIAMETER: 2 3/16" (55 mm)
STROKE: 3 1/8" (80 mm)
CAPACITY: 6" (152 mm) (chuck to column)
19 1/2" (495 mm) (chuck to base)
TABLE TILT: 0 to 45° left and right
LASER: Class III, transformer powered
WEIGHT:51 kg
I. Technical data
Table of contents
2

Safety is a combination of common sense, staying alert, and knowing how your bench drill
press works.
1. READ and become familiar with this entire instruction manual. LEARN the tool’s
applications, limitations, and possible hazards.
2. AVOID DANGEROUS CONDITIONS. DO NOT use power tools in wet or damp areas or
expose them to rain. Keep work area well-lit.
3. DO NOT use power tools in the presence of flammable liquids or gases.
4. ALWAYS keep your work area clean, uncluttered, and well-lit. DO NOT work on floor
surfaces that are slippery with sawdust or wax.
5. KEEP BYSTANDERS AT A SAFE DISTANCE FROM the work area, especially when the
tool is in operation. NEVER allow children near the tool.
6. DO NOT FORCE THE TOOL to do a job for which it was not designed.
7. DRESS FOR SAFETY. DO NOT wear loose clothing, gloves, neckties, or jewellery (rings,
watches, etc.) when operating the tool. Inappropriate items can get caught and draw you into
moving parts. ALWAYS wear non-slip footwear, and tie back long hair.
8. WEAR A FACE MASK OR DUST MASK. Drilling into materials produces dust.
9. ALWAYS remove the power cord plug from the power supply outlet when making
adjustments, changing parts, cleaning, or working on the tool.
10. AVOID ACCIDENTAL START-UPS. Make sure that the power switch is in the OFF
position before plugging in the power cord.
11. REMOVE ADJUSTING TOOLS. ALWAYS MAKE SURE all tools are removed from the
bench drill press before turning it ON.
12. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. DO
NOT leave the tool unattended until it has come to a complete stop.
13. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit.
DO NOT store anything above or near the tool.
14. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant
rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris.
15. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order.
Follow instructions for lubricating and changing accessories. See Maintenance section.
SAVE THESE SAFETY RULES
WARNING: TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY, DO NOT
PLUG IN THE BENCH DRILL PRESS UNTIL THE FOLLOWING STEPS HAVE BEEN
READ AND UNDERSTOOD.
II. General safety rules
3

16. DO NOT operate the tool if you are under the influence of drugs, alcohol or medication
that could affect your ability to use the tool properly.
17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming,
breakage, improper mounting, or any other conditions that may affect the tool’s operation.
Any part that is damaged should be properly repaired or replaced before use.
18. MAKE THE WORKSHOP CHILDPROOF. Use padlocks, master switches, and ALWAYS
remove starter keys.
LASER SAFETY
•The laser light beam used in this system is Class III. These lasers do not normally present
an optical hazard, although staring at the beam may cause flash blindness.
SAVE THESE SAFETY RULES
WARNING: DO NOT STARE DIRECTLY AT THE LASER BEAM! A HAZARD MAY EXIST
IF YOU DELIBERATELY STARE INTO THE BEAM, PLEASE OBSERVE ALL SAFETY
RULES AS FOLLOWS:
• THE LASER SHALL BE USED AND MAINTAINED IN ACCORDANCE WITH THE
MANUFACTURER'S INSTRUCTIONS.
• NEVER AIM THE BEAM AT ANY PERSON OR AN OBJECT OTHER THAN THE
WORKPIECE.
• DO NOT PROJECT THE LASER BEAM INTO THE EYES OF OTHERS.
• ALWAYS ENSURE THE LASER BEAM IS AIMED AT A WORKPIECE THAT DOES NOT
POSSESS REFLECTIVE SURFACES, AS THE LASER BEAM COULD BE PROJECTED
INTO YOUR EYES OR THE EYES OF OTHERS.
WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE HAZARDOUS
TO YOUR HEALTH. ALWAYS OPERATE THE DRILL PRESS IN A WELL-VENTILATED
AREA. USE DUST COLLECTION SYSTEMS WHENEVER POSSIBLE.
II. General safety rules ... continued
4
ALWAYS WEAR EYE PROTECTION.
A bench drill press can throw foreign objects into the eyes which
could cause permanent eye damage.
ALWAYS wear safety goggles (not glasses). Ordinary eyeglasses
have only impact-resistant lenses...they are NOT safety glasses.

1. NEVER TURN THE BENCH DRILL PRESS ON until the table is clear of all foreign
objects (tools, scraps, etc.).
2. ALWAYS KEEP hands and fingers away from the drill bit.
3. DO NOT drill materials that do not have a flat surface—unless a suitable support is used
(clamp or vise).
4. NEVER start the drill press with the drill bit pressed against the workpiece.
5. MAKE SURE the table lock is tightened before starting the bench drill press.
6. NEVER layout, assemble, or set-up any work on the table while the drill is ON.
7. MAKE SURE drill bit is securely locked in the chuck.
8. MAKE SURE chuck key is removed from the chuck before turning power ON.
9. ADJUST the table or depth stop to avoid drilling into the table.
10. ALWAYS stop the drill before removing scrap pieces from the table.
11. USE CLAMPS or a vise to secure a workpiece to the table. This will prevent the
workpiece from rotating with the drill bit.
12. DO NOT wear gloves when operating a drill press.
13. BEFORE LEAVING THE MACHINE, SHUT THE POWER OFF, remove the drill bit and
clean the table.
14. SET THE DRILL PRESS to the speed that is appropriate for the material being drilled.
15. SHOULD any part of your bench drill press be missing, damaged, or any electrical
component fail to perform properly, shut the power OFF and unplug the drill press.
Replace missing, damaged, or failed parts before resuming operation.
SAVE THESE SAFETY RULES
WARNING: DO NOT OPERATE YOUR BENCH DRILL PRESS UNTIL IT IS
COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS.
III. Specific safety rules for bench drill presses
5