KMART 42949503 User manual

WARNING! Not suitable for children under 3 years. Small parts. Choking hazard.
Maximum user weight 45kg for each section. This unit is designed to be used
safely by up to 5 children simultaneously. Only for domestic use. Outdoor use
only.
Platform Spin Swing Set
Instruction Manual
Keycode 42949503

1
the
swing set
This swing set complies with AS/NZS ISO 8124.6.23.
instruction
swing

Unexpected movement (i.e.: tipping, lifting and overturning) of the swing set may result in serious injury or death.
The swing set must be securely anchored before use.
The owner should disassemble and dispose of the playground equipment in such a way that no unreasonable hazards
will exist at the time the playground equipment is discarded.
2
Maximum weight of 100 pounds(45kg) for swing section.

Proper Play Conditions:
¾Always use the product in a well-lit area. Do not use without lighting during dawn, dusk or in
complete darkness!
¾Maintain clear space on all sides of the product. Such objects include walls, fences, tree
limbs/trunks, electrical power wiring, rocks, sp rinkler heads or other recreational objects (i.e.
swing sets, swimming pools).
¾The product must not be used in windy conditions as wind can cause unexpected movement
of the product.
JCA Collective
Email: [email protected]
Phone Number: [phone]
Office Hours: Monday to Friday 9am to 5pm
3

SAFETY NOTES:
zAdult assembly required.
zAdult supervision required when product in use.
zFor domestic outdoor use
zChildren must understand how to use the product safely.
zDO NOT allow children to play around product when in use
zDO NOT allow more than 1 child to use this product at a time.
MAINTENANCE INSTRUCTIONS:
zChecking fixings regularly. Injury may be a result if you fail to do so .
zChecking the nuts and bolts on a regular basis for tightness, sharp edges or deterioration.
Tighten or replace when required.
Check paintwork regularly and if needed touch up with enamel
4
z
z
z

Do not use the mat when it is wet.
Limit the time of continuous usage (make regular stops).
Check that all spring-loaded (pit pin) joints are still intact and cannot become dislodged during playing
Check that mat, padding and enclosure without defects
z
z
Check all nuts and bolts for tightness and tighten when required.
z
Oil all metallic moving parts.
z
Check all coverings and bolts for sharp edges and replace when required.
z
Check swing seats, chains, ropes and orther means of attachment for evidence of deterioration;
replace when required in accordance with the manufacturer's instructions.
z
Sand rusted areas and tubular members and repaint using a non-lead based paint when required.
z
5HWDLQWKHLQVWUXFWLRQVIRUDVVHPEO\PDLQWHQDQFHDQGVDIHXVHIRUIXWXUHUHIHUHQFH
z

5
This swing set is designed for use by children ages 3-8 years old with a maximum weight of
45kg for each section.
.)m88.1( ”47 si tes gniwssihtfofall thgieh mumixam ehT
This product is designed for normal residential use only. This product is not designed for use in day
care, nurseries, or other public places. This product is to be assembled by adults only in the manner
described within this instruction manual.
This product must be anchored. Anchors are included with this swing set.
Anchoring is necessary to prevent tipping, lifting, and overturning. We recommend anchoring the
swing set in concrete, especially in soft or sandy soil.
To anchor the swing set in concrete, dig a hole at least 5” (12.7cm) deep and 10” (25.4cm) to
12” (30.5cm) in diameter. Place the swing set leg in the hole, preferably on a brick or stone to keep
if from sinking. Be sure the swing leg is set 3” (7.6cm) below the ground. Pour concrete
recommended surfacing instruction
in this manual. Allow the concrete to cure according to the concrete manufacturer’s instruction
before use.
Points to remember when locating and placing the swing set:
· Place your swing set on level ground a MINIMUM of six (6) feet (1.83m) from any s tructure or
obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
· Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or any
other hard surface. A fall on to a hard surface can result in serious injury to the equipment user.
· Do not place your swing set underneath electrical lines. If you must, e nsure that there is a minimum
overhead clearance of six (6) feet (1.83m).
· The swing set should be assembled near the location it will be permanently anchored.
Only adults should assemble or disassemble the swing set. For safety reasons and ease of assembly
it is recommended that two adults assemble the swing set. The swing set includes two 5mm Socket
head wrenches. You will also need an adjustable wrench, a Cross head screwdriver and a needle-nose
pliers.
Assembly
Specifications
Anchoring

6
Location and Placement of Your Swing Set
Proper placement and maintenance of protective surfacing is essential.
Be sure to:
• Extend surfacing at least 6 feet (1.83m) from the equipment in all
directions. Swing set must be placed a minimum of 6 feet (1.83m)
from any structure or obstruction such as a fence, garage, house,
overhanging branches, laundry lines, or electrical wires.
• Do not place your swing set underneath electrical lines. If you must,
ensure that there is a minimum overhead clearance of 6 feet (1.83m).
• Do not install swing set over concrete, asphalt, packed earth, grass,
carpet, or any other hard surface. A fall on to a hard surface can result
in serious injury to the equipment user.
• For safe playing swings, extend protective surfacing 12 feet (3.66m) in front
of and behind the point of suspension of the swing.
• The following diagram shows how much obstacle-free surfacing
should be used for the swing set. The shaded portion is where the
protective surfacing must be placed.
12 ft. (3.66 m)
6 ft. (1.8
m)
6 ft. (1.8 m) 6 ft. (1.8 m)
6 ft. (1.8 m)
6 ft. (1.83 m)
6 ft. (1.83 m)
6 ft. (1.83 m)
6 ft. (1.83 m)
Dimensions are not to scale.

PictureNO. Qty
1PC
1PC
1PC
1PC
1PC
2PCS
4PCS
2PCS
1PCS
2PCS
6PCS
2PCS
2PCS
Description
Top Bar A
Connection
tube(three-way)
1PCS
2PCS
Top Bar B
Top Bar C
Top Bar D
Leg A
Climbing tube
Rectangular
tube A
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
7
Leg B
Leg C
Support Bar A
Support Bar B
Support Bar C
Rectangular
tube B
Connection
tube(four-way)

A16
A17
A18
A19
A20
A21
1PC
1PC
1PC
1PC
1PC
1PC
8
Platform fabric
Rectangular Platform
fabric
Protect Net
Tent fabric
Sandpit fabric
Climbing webbing
NO. Picture Description Qty

9
M10*50（pre-assembled)
M8*50（pre-assembled)
M8*56（pre-assembled)
M8*52（pre-assembled)
M8*70
Anchor
14st
18st
4st
2st
8st
7pcs
a1
a2
a3
a4
a5
a6
NO. Picture Description Qty

10
M10*30（2PC）
U screw
M10*30（2PC）
U screw（pre-assembled)
2st
B1
B2
C1
C2
C3
c1
c2
b1
b2
4PCS
1PC
2ST
2st
4st
1ST
1PC
1st
Nest swing Top rail
Nest swing set
Nest swing rope
Nut with washer
（pre-assembled)
Spin parts
Connect steel plate
M8*75
Qty
DescriptionPicture
NO.

11
Platform, Climbing Ladder and Sandpit Assembly Part
A14
A4
A15
a1
1.Connect the Top Bar D (A4) with the Connection tube (three-way) A14, and connect
the other end with the Connection tube(four-way) A15,tighten them with
the screw a1(M10*50)

A7
A7
a2
a2
A12
12
A17
a5
2.Connect 4pcs Leg C(A7) with Connection tube (three-way)A14 and
Connection tube(four-way)A15, tighten them with screw a2(M8*50).
3.Put the Rectangular A(A12) go through the two longer tunnels of the
Rectangular Platform fabric(A17),and connect with Leg C(A7) by tightening screw
a5(M8*70).

13
A11
a5
A20
A13
a2
4.Connect the 6pcs climbing tube(A11) with Leg C(A7), two of the climbing tube (A11) need
to go through the Rectangular Platform fabric (A17), tighten them with screw a2(M8*50)
as below picture show.
5.Put the Sandpit fabric(A20) at the bottom, two Rectangular tube B(A13) go through
the Sandpit fabric (A20) from the two sides as below show, and use the screw a5(M8*70)
to tighten them.

6.Open the Tent fabric(A19),the finished part go through the tunnel of it, then tighten the
touch fastener one by one as below picture show.
A19
14

15
a1
A21
A1
Climbing webbing assembly part
1.Put the Top Bar A(A1) go through the top hole of the Climbing webbing(A 21),then
connect the Top bar A(A1)with the Connection tube(four-way)A15 by tightening
the screw a1(M10*50) as below picture show.

16
a1
A5
A6
A6
2.Put the Leg A(A5) go through the shorter end of the Climbing webbing(A21), then
connect with the Top Bar A(A1) by tightening the screw a1(M10*50) as below show.
3.Put one of the Leg B(A6) go through the 4 holes of the Climbing webbing(A21) top end,
the other one go through the 2 holes of the Climbing webbing(A21) low end, then connect
these two Leg B(A6) with the Connection tube(four-way)A15 by tightening the screw
a2(M8*50) as below picture show.

17
a3
A16
a3
a3
A8
A21
A8
A9
A16
4.Put 2 Support Bar A(A8) go through the Platform fabric(A16), at the same time, one of the
Support Bar A(A8) need to go through the two holes of the low section
Climbing webbing(A21), the Support Bar B(A9) need to go through the other side of
the Platform facric(A16) as below picture show.
5.Connect the Platform fabric(A16) with the Leg A(A5) and Leg B(A6) by tightening
screw a3(M8*56)
A6
A6
A5

18
a4
a3
A18
6.Connect the 2 pcs Support Bar C(A10) with the Climbing webbing(A21) by going
through the two holes as below show,and connect with Support Bar B(A6) by tightening
screw a4(M8*52),connect with Support Bar A by tightening screw a3 （M8*56).
A10
A10
A6
A5
A6
7.Connect the Protect Net(A18) with Support Bar B(A9) by the touch fasteners,at the
same time. Also connect the Protect Net(A18) with the Support Bar B(A9) by touch
fasteners.
A9
A6
A6

19
A2B2
b2
Spin Parts and Nest swing set assembly parts
1.Take down the bigger Pin from the assembled spin parts(B1).
2.Assemble the U screw(b2)on the Top BarB(A2) which has slot, and put the Connect
steel plate (B2) under the Top Bar B(A2) accordingly,then connect them together as below
shows (Attention! The direction of the Top Bar B,there are 5 holes in the top and 6 holes
in the bottom).