lighting PLUS 300 LED BSW User manual
User manual
300 LED BSW
Please read the instructions carefully before use
2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications…………………………………………………………………………4
3.Control Menu ……………………………………………………………………………………5-6
4.DMX Channels ……………………………………………………………………………………7-10
5.Trouble Shooting…………………………………………………………………………………11
6.Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.
3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
4
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Light Sources: 300W High Power White LED
Max Power Consumption: 550W
Power Input: 100-240V, 50/60Hz
Color Tempreture: 6500K-8500K
LED Lifespan: 50000 hours
Operating mode: DMX512,Auto, Sound active, Master/slave
Channel mode: 20 / 25 DMX512 Channel
Pan: 540°(16bit) Electric correction
Tilt：270° (16bit) Electric correction
Color wheel: 7 colors +open, rainbow effect, arbitrary positioning.
2 Static Gobo Wheels: One packed with 8 static +open, with shake water flow effect, positive and
negative,,which can produce ripple,flame,night sky effect. Another one is 6 color gobo,make rainbow
effect
Rotation Gobo Wheel (glass gobo): 7 rotating /interchangable + open, pattern rotating, pattern water
flow effect.
Prism: Rotating 3-facet prism, iris aperture free amplification and reduction, add an effect fixed
plate,water flow effect with speed adjustable
Function:Frost, Focus and Zoom
0-100% linear dimming, fit advanced iris aperture zoom effect, fast, precise, smooth, one of the most
advanced optical system in the same class of products.
Strobe: 0-25Hz/s, sync pulse strobe, random pulse stroboscopic,etc.
Focus: machanical focus
Zoom range:8°-40°
Display: Touch screen, English and Chinese interchangeable, reversible display.
Over heat protection
IP level: IP20
Dimension: 480x390x580mm, NW:20 kg
Packing Size: 510x420x600mm
Gross weight: 21kg
5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
MainMenu
Second Menu
Third Menu
Forth Menu
Settings
Dmx Address
1 - 512
Fixture Set
Dmx Mode
STD / EXT
Run Mode
DMX / Host
Pan Inverse
Close / Open
Tilt Inverse
Close / Open
Display
Language
CH / EN
Display Flip
Close / Open
Display Mode
Show / 60s
Reset
XY Reset
Cance / Run
Motor Reset
Cance / Run
All Reset
Cance / Run
Factory
Cance / Run
Info
Time
Current Time
xxxH
Show Time
xxxH
Power Count
xxx
Sensor
xxxxxx
Software Version
Panel
Vx.xxx
Motor_XY
Vx.xxx
6
Motor
Vx.xxx
Manual
Pan
0 - 255
PanFine
0 - 255
Tilt
0 - 255
TiltFine
0 - 255
⁞
⁞
Factory
Password
0 - 255
Pan
0 - 255
Tilt
0 - 255
Iris
0 - 255
Color
0 - 255
RotGobo
0 - 255
Gobo Rot
0 - 255
Fix Gobo
0 - 255
Frost
0 - 255
Color7
0 - 255
Effect
0 - 255
Prism
0 - 255
PrismRot
0 - 255
Zoom
0 - 255
Focus
0 - 255
7
4.DMX Channels
DMX channel´s functions and values (20/25DMX channels)
CH 25
CH 20
DMX Value
Function
Function Illustration
1
1
0－255
Pan
Pan
2
2
0－255
Pan fine
Pan fine
3
3
0－255
Tilt
Tilt
4
4
0－255
Tilt fine
Tilt fine
5
5
0－255
P/T Speed
P/T Speed
6
6
Function
Macro function
0－139
Blank
140－149
X Y reset
150－189
Effect reset
190－199
Blank
200－209
Light reset
210－255
Blank
7
7
Strobe
Shutter
0-3
Closed
4-103
Slow - fast
104-107
Open
108-207
Fast strobe-slow strobe
208-212
Open
213-251
Random slow - fast
252-255
Open
8
8
Dimmer
Dimmer
0－255
Linear dimmer
9
9
Color
Colour
0-9
white
10-19
Colour 1
20-29
Colour 2
30-39
Colour 3
40-49
Colour 4
50-59
Colour 5
60-69
Colour 6
70-79
Colour 7
80-89
Colour 8
90-99
Colour 9
100-109
Colour 10
110-119
Colour 11
120-129
Colour 12
8
130-139
Colour 13
140-149
Colour 14
150-159
Colour 15
160-204
Fast rotation - slow rotation
205-210
Stop
211-255
Slow rotation - fast rotation
10
*
Color fine
Color Fine
0－255
Linear
11
10
Fixed gobo 1
Gobo 1
0-4
white
5-24
Gobo1
25-44
Gobo2
45-64
Gobo3
65-84
Gobo4
85-89
white
90-119
Fast rotation - slow rotation
120-125
Stop
126-155
Slow rotation - fast rotation
156-180
Gobo 1 shake
181-205
Gobo 2 shake
206-230
Gobo 3 shake
231-255
Gobo 4 shake
12
11
Fixed gobo 2
Gobo 2
0-9
white
10-19
Gobo 1
20-29
Gobo 2
30-39
Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-89
Gobo 8
90-112
Fast rotation - slow rotation
113-120
Stop
121-143
Slow rotation - fast rotation
144-157
Gobo 1 shake
158-171
Gobo 2 shake
172-185
Gobo 3 shake
186-199
Gobo 4 shake
200-213
Gobo 5 shake
214-227
Gobo 6 shake
228-241
Gobo 7 shake
9
242-255
Gobo 8 shake
13
12
Rotary gobo
R.Gobo
0-9
white
10-19
Gobo 1
20-29
Gobo 2
30-39
Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-129
Fast rotation - slow rotation
130-135
Stop
136-185
Slow rotation - fast rotation
186-195
Gobo 1 shake
196-205
Gobo 2 shake
206-215
Gobo 3 shake
216-225
Gobo 4 shake
226-235
Gobo 5 shake
236-245
Gobo 6 shake
246-255
Gobo 7 shake
14
13
Rotary gobo rotation
Rotatry gobo rotation
0－63
Linear
64－126
Fast rotation - slow rotation
127－128
Stop
129－191
Slow rotation - fast rotation
192－193
Stop
194－255
Slow rotation - fast rotation
15
*
Rotary gobo rotation
fine
Rotary gobo rotation fine
0－255
Linear
16
14
0-127
Prism
white
128-255
Prism
17
15
Prism rotation
Prism rotation
0－63
Linear
64－126
Fast rotation - slow rotation
127－128
Stop
129－191
Slow rotation - fast rotation
192－193
Stop
194－255
Slow rotation - fast rotation
18
*
Prism 1 rotation fine
Prism rotation fine
0－255
Linear
19
16
Iris
Iris
0-134
Linear
10
135-164
Fast open，slow close
165-194
Slow open，fast close
195-224
Normal fain effect
225-255
Random rain effect
20
17
0-127
Frost
white
128-255
Frost
21
18
0-255
Rainbow effect
6colors
22
19
0-255
Focus
Focus
23
*
0-255
Focus fine
Focus fine
24
20
0-255
Zoom
Zoom
25
*
0-255
Zoom fine
Zoom fine
11
5.Trouble Shooting
F
ollo
w
ing
a
r
e
a
few
c
o
mm
on
p
r
oble
m
s
th
a
t
m
a
y
occu
r
d
uring
ope
r
a
tion
.
He
r
e
a
r
e
s
o
m
e
s
ug
g
es
tion
s
fo
r
ea
s
y
tr
ou
b
leshooting
:
A.
The
un
it
does
no
t
work
,
no
li
ght
a
n
d
t
he
f
a
n
d
o
es
no
t
w
o
r
k
1.
Check
th
e
c
on
nect
ion of p
owe
r
a
nd
m
a
in
fu
s
e
.
2.
M
eas
ure
th
e
m
a
ins
volt
a
ge
on
th
e
m
a
i
n
co
nn
e
ct
o
r
.
3.
Check
th
e
pow
er
on
LED
.
B.
N
o
t
responding
t
o
D
MX
c
on
t
ro
ll
er
1.
D
M
X
LED
s
h
ou
ld
b
e
on.
If
no
t,
che
ck
D
M
X
co
n
nectors,
ca
b
l
es
to
s
ee
if
link
p
r
ope
r
ly
.
2.
If
th
e
D
M
X
LE
D
i
s
on
a
nd
no
r
espons
e
t
o
th
e
c
h
a
nn
el,
che
ck
th
e
a
dd
r
ess
s
etti
ng
s
a
nd
D
M
X
p
ol
a
r
ity
.
3.
If
y
ou
h
a
ve
i
nter
m
ittent
D
M
X
s
ig
n
a
l
p
r
oble
m
s
,
che
ck
th
e
p
ins
on
c
onn
ecto
r
s
or
on
PCB
of
th
e
u
nit
or
the
p
r
ev
iou
s
on
e.
4.
Tr
y
to
us
e
a
no
th
er
D
M
X
co
ntroller
.
5.
Check
if
th
e
D
M
X
ca
b
le
s
r
un
ne
a
r
or run
a
lon
g
s
id
e
t
o
h
ig
h
volta
ge
c
a
b
les
th
a
t
m
a
y
c
a
us
e
d
a
m
a
ge
or
in
terfer
ence
to
D
M
X
inter
face
circui
t.
C
.
One
of
the
cha
nn
el
s
is
no
t
w
o
r
k
ing
w
el
l
1.
Th
e
s
tep
p
er
moto
r
m
ig
h
t
b
e
dam
a
g
ed
or
the
c
a
b
le
c
on
nect
ed
to
th
e
PCB
is
b
r
oken.
2.
Th
e
m
oto
r
’
s
d
r
ive
IC
on
th
e
PCB
m
ig
h
t
b
e
o
ut
of
co
ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Table of contents
