LM3X Lumi Lazr 4G User manual
4G
2
https://lm3x.guide/
Device type 4G
Device ID
my.lumiverse.com
Login
Password
Direct Wi-Fi Access
Wi-Fi Password
My New Password
Find the complete manual online
3
Device ID
my.lumiverse.com
Login
Password
Direct Wi-Fi Access
Wi-Fi Password
My New Password
Your Lumiverse Credentials
4
How to Use Your LAZR 4G?
Simply and in a fun way!
Go to the web page https://lm3x.guide/ and follow the interactive
manual. This manual contains an easy set-up guide and will help you congure your
LAZR 4G correctly.
5
1
2
3
4
5
5
3
4
1
2
6
7
8
6
7
8
Front & Back Panel
Power socket
Power button
Power LED indicator
Lumiverse ONLINE indicator
Beamer lens
Scanner lens (camera)
Air lter cover
LAN socket
6
Correct Outdoor Positioning
max 30° max 30°
7
Technical Data
Input voltage
Power consumption (max.)
Standby power consumption(typ.)
Operating temperature (typ.)
Ingress protection
Overvoltage protection
Dimensions (HxWxL)
Weight
Display type
Brightness
Laser lifespan
Native resolution (px)
Aspect ratio
Throw ratio (lens)
Camera
Audio output
Shielding
Wireless Control channels
LumiverseTM media storage
110 - 230 V ~ 50/60 Hz
550 W
30W
-20° ~ +40 °C
IP43
power supply, LAN, audio
237 x 538 x 672 mm
24 kg
LASER DLP
6.000 ANSI/lm
20.000 h
1920x1200 (WUXGA)
16:10
1.2 - 1.9
5 Mpix
2x XLR balanced audio
grounded to the chasis
GSM, Wi-Fi, GPS
400 GB
8
Important Safety Instructions
• The unit must not be exposed to splashing water.
• No leaking objects may be placed above the device.
• This device contains a non-rechargeable lithium battery.
• Failure to read and follow the below specied instructions may result in re,
personalinjury, or damage to property.
• Do not cover device while it is running.
• Do not place anything inside of the device.
• The device must be grounded via a grounded power cable using a grounded
cable and the device grounding point.
• Always use the device in an electrical circuit that is protected against short
circuit by a 16A circuit breaker with B or C characteristic.
• Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
• Installation of the equipment should be supervised by an electrician, who will
also verify the correct connection grounding and appropriate IP protection of
the components outside the device.
• Protect the power cord from being stepped on or pinched particularly at plugs.
Be sure that the power outlet is located near the unit so that it is easily acces
sible.
• Only use attachments/accessories specied by the manufacturer.
• Use only with a cart, stand, tripod, bracket, or table specied by
the manufacturer or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
• Unplug this unit when unused for long periods of time.
• Refer all servicing to qualied service personnel. Servicing is required when the
unit has been damaged in any way, such as: if power plug is
damaged, if liquid is spilled onto or objects fall into the unit, or if the unit does
not operate normally or has been dropped.
• Do not place this projector on a blanket, bedding, or any other so surface.
• Do not cover this projector with a cloth or any other item.
• Do not place inammables near the projector.
• Do not place this projector in locations near re alarms.
• Do not place this projector in a space that is poorly ventilated or conned. Allow
at least 50 cm clearance from walls and free ow of air around the projector.
9
1
2
3
4
5
7
8
9
12
34
567
8
9
6
Device Description
Fixture attachment points x 4
WIFI antenna
GNSS/LTE antenna
Grounding point
XLR audio connectors
nanoSIM connector
USB connector (only for service use)
Air intake
Air exhaust
10
1
2
13
3
2
Attachment System
Post Fixture Mount
Wall Fixture Mount
Use Screw M8x16 / 16 Nm (x 6)
Your LAZR series projector is supplied with an attachment system (optional).
There are two interchangeable mounts, one for the wall and one for the post
installation. Make sure that you use a sucient xture and always think
SAFETY FIRST!
Always use sucient
grounding protection
attached to the grounding
screw
11
Safety Instructions
• The LAZR 4G projector is weather protected (IP43) and can operate outdoors
within a operating temperature range of - 20º C < > + 40º C.
If the environment temperature exceeds the allowed limit, the projector will stop
displaying content and shut itself down. The projector will resume working when
the temperature falls back within the operating range.
• Do not turn o the device if the temperature drops below -15 °.
• The projector’s laser unit produces an extensive amount of excessive heat,
therefore there are large ventilation openings on the bottom of the machine,
AIR INTAKE and AIR EXHAUST. Always ensure that the ventilation openings are
not blocked by any objects, which could cause your projector to easily overheat.
• Your LAZR 4G projector can be operated outdoors as long as it is always
positioned horizontally within the allowed angles (see page 6).
• Always use sucient ground protection attached to the grounding screw to
prevent electric shock risk!
• Do not cover the device while it is running as it may cause it to overheat.
• ALWAYS REMOVE THE PROTECTIVE LENS CAP from the lens before you turn
your projector ON!
• Do not use the device when it is damaged and do not try to dismantle it.
There is a risk of electric shock!
• Do not use any damaged cabeles!
• The projector is equipped with IP67 plug, ensure that you use a compatible
plug or anypower connector suitable for outdoor use.
• The projector is a heavy machine, therefore always install it carefully and ensure
it is securely fastened. Avoid installing the device in places where falling
may cause injury!
• Ensure there are no objects closer than 1 m in the projector light cone.
Strong light might cause re!
• Aiming the projector towards the sun may cause re, or damage DLP unit.
• Do not look into the projector lens while the lamp is on! The intense light beam
may damage your eyes.
• Install the projector carefully so you do not blind passers-by with strong light!
• Do not step on the projector or place any objects on top of it. Besides probable
physical damage to the projector, doing so may result in accidents
or possible injury.
12
LASER Safety Instructions
• As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015.
• This symbol indicates that there is a potential hazard of eye exposure
to laser radiation unless the instructions are closely followed.
This Laser Product is designated as Class 3R during all
procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or
reected toward other people or reective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation
if the included instructions are not followed.
Caution – use of controls or adjustments or
performance of procedures other than those specied herein
may result in hazardous radiation exposure.
Laser parameters:
• Wavelength: 450nm - 460nm (Blue)
• Mode of operation: Pulsed, due to frame rate
• Pulse width: 1.34ms
• Pulse repetition rate: 120Hz
• Maximum laser energy: 0.698mJ
• Total internal power: >100w
• Apparent source size: >10mm, at lens stop
• Divergence: >100 mili Radian
13
• The projector is equipped with an automatic dehumidication system to prevent
any damage caused by moisture.
• Once installed outdoors, it is important to keep the projector ON and connected
to a reliable permanent power source!
• If a blackout occurs, the projector will wake up and continue playing the show
automatically once the power source has been restored.
Power Management
LED Indications
LUMI Logo Indication
• Shining - on-line (connected to internet).
• Not shining - o-line, connection to the internet has been lost (this
is always the case a few moments aer a start/restart).
Color LED Status
• Not shining - device is o
• White pulsing -Wait, your device is booting, shutting down, or loading. Wait.
Do not unplug from electricity!
• White shining - device is on and ready.
• Green pulsing - waiting for the projector lamp to heat up / cooldown.
• Green shining - media is currently playing.
• Yellow pulsing - temperature too warm or ventilation blocked. Wait for cooldown.
• Red shining - check cables. See troubleshooting.
• Red pulsing - factory reset is in progress, do NOT unplug the device from power.
Connectors Matching
To maintain functional IP protection, use only with these Neutrik® connectors:
POWER connector: NAC3FX-W-TOP (1 pcs. included)
LAN connector: NE8MC6-MO
AUDIO connector: NC3FXX-HD-D
14
Maintenance
Air Filter
The LAZR 4G projector is
equipped with an inter-
changeable air lter. We
recommend replacing the
air lter once a year. In
dusty environment replace
the lter more oen.
Laser
Laser lifespan is 20,000
hours. See, for how many
hours has your laser
been used in Lumiverse
UI Settings/Advanced/
Sensors
Lens
Dirt on the projector
lens may aect the light
show quality and the
scanner results. Clean
with a regular so glass
cleaning cloth. Use a
screwdriver to remove
the lens for cleaning.
15
Troubleshooting
Support
Soware Upgrade
In case a projector malfunction occurs, try the following steps:
Reboot
In order to resolve a malfunction issue, try the REBOOT command from the
POWER BUTTON menu in the Lumiverse UI
Turn O and Turn On
Lumiverse UI oine? Turn the projector OFF by pressing the power button to
turn o the device immediately. If it does not work, pull the power cord out of the
machine and reconnect. Disconnect and reconnect the power connector even if
you are unable to turn on the projector.
Factory Reset
The factory reset will erase some of your data and restore the system to its facto-
ry settings. Turn the device OFF and wait for 5 seconds. Turn the device ON and
hold down the power button until the LED indicator turns red.
Didn’t help? Contact our support!
supp[email protected]om
LM3X.com company is constantly developing new features, upgrades, securi-
ty systems, and bug xes.
Information about new updates can be found in LumiverseTM and will be
installed on your device at your request.
16
Declaration of Conformity
Hereby declare that:
Product: OUTDOOR PROJECTOR
Product family: T
Machine Type: T4
Is compliant with the essential requirements and any other relevant provisions of
the following EC directives, and that all the necessary steps have been taken and
are in force to assure that the production units of the same product will continue
to comply with the above specied requirements.
ELECTRICAL SAFETY TEST
The following regulations have been used:
EN 62368-1:2014 + AC:2015-05 + A11:2017
ELECTROMAGNETIC COMPATIBILITY TEST
The following regulations have been used:
EN 55024:2010
EN 55032:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 61000-4-2:2008
EN 61000-4-3:2006 +A1:2007 +A2:2010
EN 61000-4-4:2012
EN 61000-4-5:2014
EN 61000-4-6:2014
EN 61000-4-11:2004
17
Declaration of RoHS2 Compliance
Product: OUTDOOR PROJECTOR
Trade Name: LUMITRIX
Machine Type: T4
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values
issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent Chromium (Cr6+)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers (PBDE)
Proposed Maximum
Concentration
0.1%
0.1%
0.01%
0.1%
0.1%
0.1%
Actual
Concentration
< 0.1%
< 0.1%
< 0.01%
< 0.1%
< 0.1%
< 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (=<500 mm): maximum 3.5 mg per lamp.
(2) Medium length (>500 mm and =<1,500 mm): maximum 5 mg per lamp.
(3) Long length (>1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
18
Cellular network
CELLULAR NETWORK - E:
Variant for EMEA/Brazil/APAC
• LTE-FDD: B1/B3/B5/B7/B8/B20/B28/B32
• LTE-TDD: B38/B40/B41
• 2×CA: B1+B1/B5/B8/B20/B28;
B3+B3/B5/B7/B8/B20/B28;
B7+B5/B7/B8/B20/B28;
B20+B32; B38+B38; B40+B40; B41+B41
• WCDMA: B1/B3/B5/B8
LAZR 4G is made with two types of cellular network receiver.
The type of modem used in your device is indicated on the side of the device.
If you use your device in a dierent location than what your machine is
congured for, you may experience problems connecting your device using
the cellular network.
CELLULAR NETWORK - A:
Variant for America/Canada/Mexico/Argentina
• LTE-FDD: B2/B4/B5/B7/B12/B13/B25/B26/B29/B30/B66
• 2×CA: B2+B2/B5/B12/B13/B26/B29;
B4+B4/B5/B12/B13/B26/B29;
B7+B5/B7/B12/B13/B26/B29;
B25+B5/B12/B13/B25/B26/B29;
B30+B5/B12/B13/B26/B29;
B66+B5/B12/B13/B26/B29/B66
• WCDMA: B2/B4/B5
19
Notes:
Table of contents
