Logiquip ParWire User manual
ASSEMBLY GUIDE
CAUTION Read and understand all of the instructions and safety
information in this document before operating this product.
ParWire®BASKET SHELVING
ASSEMBLY GUIDE
(800) 665-3760
2|
2B
PARWIRE®BASKET SHELVING
PARTS & HARDWARE
TOOLS NEEDED
Nylon or Rubber Base Hammer
Swivel Caster Brake Caster Leveling Feet
1
3
4
5
*Basket Shelving can include FLAT, SLANTED, or GLIDE Baskets.
†Based on your order, you will receive either Casters OR Leveling Feet.
PARTS & HARDWARE QTY
1. Wire Shelves 2
2. Basket Shelving*Varies
3. Posts 4
4. Split Sleeves 4/Shelf
5. Casters†4
6. Leveling Feet†4
6
FLAT
GLIDE
SLANTED
2A
1
3
4
5
2A
2B
2C
2C
ASSEMBLY GUIDE
www.logiquip.com |3
ASSEMBLY INSTRUCTIONS
Each ParWire®Basket Shelving Cart comes with two (2) LQS Flat Wire Shelves; one to be placed at the bottom and one to be
placed at the top for added stability.
MOUNT FIRST SHELF (BOTTOM)
Install bottom shelf first using one (1) of the two (2) LQS Flat Wire shelves and work your way up. Refer to location numbers
on posts. Refer to location of numbers on posts, snap tapered split sleeves on each post at the desired position for bottom
shelf. The thickest part of the tapered split sleeve goes to the bottom side of post. Be sure that the split sleeves have been
seated properly in the groove.
MOUNT PARWIRE BASKET SHELVES
Continue process for the ParWire Basket Shelves by snapping split sleeves in the preferred location as before and sliding the
shelf into position. Follow the same procedure with each shelf working from the bottom up.
MOUNT LAST SHELF (TOP)
Mount the second LQS Flat Wire Shelf last at the top of your rack/cart.
LEVELING OF UNIT (ONLY FOR CARTS WITHOUT CASTERS)
For carts/racks with leveling feet place unit at desired location, and level using a bubble level. The leveling bolts, on post
bottom, allow ½” adjustments.
4 Shelf Heavy Duty Wire Shelving Rack
Vendor Stock# 4T601848C-LD
Assembly Instructions
Questions, Problems, Missing Parts?
Before returning to your retailer, CALL OUR CUSTOMER SERVICE DEPARTMENT at
1- 866-375-7994, 9 a.m. - 5 p.m. EST. MONDAY- FRIDAY. E-Mail: sales@shelfadditions.com
Tools Required For Assembly Parts List
No tools required for assembly. A (4) Shelf C (4) Bottom Poles with Levelers Pre-installed
Helpful - Rubber Mallet B (32) Plastic Tapered Lock+4 extra D (4) Top Poles with Pole Connector & Caps
Pre-installed
Note: Black plastic discs used for packing only - Discard
SPECIAL WARNINGS
Assemble the item on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.
Use care when handling. May require two adults for safe assembly.
CARE AND MAINTENANCE
Periodically check and make sure that all components are in their proper position, are free from damage and that all connectors are tight.
ASSEMBLY INSTRUCTIONS Estimated Assembly Time: Approximately 25 minutes
1. Post Assembly
Screw the two post sections together. Hands tighten. Note: the top
section has pole connector & cap. The bottom section has leveler.
2. Bottom Shelf Assembly
a. Locate the desired position of the bottom shelf.
Note: Bottom shelf should be no more than six inches from the floor.
b. Insert four plastic tapered lock sets in the appropriate
pole groove, one in each pole. Ensure tapered end is up (see arrow on lock).
c. Place shelf on its side and slide each pole with tapered locks
through the bottom of the shelf until snug.
d. After all poles are in place, position the unit in the upright position.
e. Push down on each corner of the shelf, ensuring the shelf is in a
fully locked position.
3. Additional Shelf Assembly
a. Locate the desired position of the next lowest shelf and insert
the tapered locks into the poles.
b. Slide the shelf down from the top of the poles and onto the tapered locks.
Push down on each shelf corner, ensuring the shelf is in a fully locked position.
c. Repeat for the remaining shelves.
4. Leveler Adjustment
a. Move assembled unit to the selected room location.
b. If required, adjust levelers to ensure the unit is level.
Rotating the levelers counter clockwise raises the poles.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for
one year from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at
no charge or at our option replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-375-7994 for return authorization and shipping instructions. You
may be required to present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed
responsibility of the purchaser. Any damage to the product by accident, misuse or improper installation, or by affixing accessories not
produced by the manufacturer, are the purchaser’s responsibility.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for
incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be
accorded by law. This warranty gives you specific legal rights and you also have other rights that vary from state to state. This warranty
supersedes all prior warranties.
REV: 8/1/18
5 Shelf Wire Shelving Rack
Item# 5TB-12 / 5TZ-12
Assembly Instructions
Questions, Problems, Missing Parts?
Before returning to your retailer, CALL OUR CUSTOMER SERVICE DEPARTMENT at
1- 866-375-7994, 9 a.m. - 5 p.m. EST. MONDAY- FRIDAY. E-Mail: sales@shelfadditions.com
Tools Required For Assembly Parts List
No tools required for assembly. A (5) Shelf C (4) Bottom Poles With Levelers Pre-installed
Helpful - Rubber Mallet B (22) Plastic Tapered Lock Sets D (4) Top Poles with Pole Connector & Caps Pre-installed
Note: White plastic discs used for packing only - Discard
SPECIAL WARNINGS
Assemble the item on a soft, non-abrasive surface, such as carpeting, to avoid scratching the finish.
Use care when handling. May require two adults for safe assembly.
CARE AND MAINTENANCE
Periodically check and make sure that all components are in their proper position, are free from damage and thatall connectors are tight.
ASSEMBLY INSTRUCTIONS Estimated Assembly Time: Approximately 30 minutes
1. Post Assembly
Screw the two post sections together. Hands tighten. Note: the top
section has pole connector & cap. The bottom section has leveler.
2. Bottom Shelf Assembly
a. Locate the desired position of the bottom shelf.
Note: Bottom shelf should be no more than sixinches from the floor.
b. Insert four plastic tapered lock sets in the appropriate
pole groove, one in each pole. Ensure tapered end is up (see arrow on lock).
c. Place shelf on its sideand slide each pole with tapered locks
through the bottom of the shelf until snug.
d. After all poles are in place, position the unit in the uprightposition.
e. Push down on each corner of the shelf, ensuring the shelfis in a
fully locked position.
3. Additional Shelf Assembly
a. Locate the desired position of the next lowest shelfand insert
the tapered locks into the poles.
b. Slide the shelfdown from the top of the poles and onto the tapered locks.
Push down on each shelf corner, ensuring the shelf is in a fully locked position.
c. Repeat for the remaining shelves.
4. Leveler Adjustment
a. Move assembled unit to the selected room location.
b. If required,adjust levelers to ensure the unitis level.
Rotating the levelers counter clockwise raises the poles.
1-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for
one year from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at
no charge or at ouroption replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-375-7994 for return authorizationand shippinginstructions. You
may be required to present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed
responsibility of the purchaser. Any damage to the product by accident, misuse or improper installation, or by affixing accessories not
produced by the manufacturer, are the purchaser’s responsibility.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for
incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be
accorded by law. This warranty gives you specific legal rights and you alsohave other rights that vary from state to state. This warranty
supersedesall prior warranties.
2/6/15 K
Snap plastic
tapered split
sleeves on
each post
Install bottom shelf by
sliding over the posts
Tap very lightly with a nylon
or rubber base hammer to
seat the basket shelf on
the split sleeves
Install top shelf by
sliding over the posts
ASSEMBLY GUIDE
www.logiquip.com |4
2
3
PARWIRE®GLIDE BASKET MOUNTING
PARTS & HARDWARE
TOOLS NEEDED
• Drill
• Screw Driver
Looks may vary based on brand of
Toggle Bolt or Screw.
4
5
*D Ring Kit includes D Ring and two (2) Wall Mounting Brackets.
†Toggle Bolts are used for drywall and need to hold a minimum of 100 pounds each.
Toggle Bolts are provided by installer.
‡Screws are used for cinder block and need to hold a minimum of 100 pounds each.
Screws are provided by installer.
PARTS & HARDWARE MODEL QTY
1. Carabiner TETHERSSC25 2
2. Metal Lanyard TETHERLAN6 1
3. D Ring Kit*TETHERSSDR1 1 Kit
4. Toggle Bolts†—2
5. Screws‡—2
1
1
ASSEMBLY GUIDE
(800) 665-3760
5|
PARWIRE®GLIDE BASKET MOUNTING INSTRUCTIONS
ParWire Shelving that includes the GLIDE Basket is not for use in mobile applications. The shelving unit must be anchored to
the floor or wall, or to another similar sized shelving unit in a back:back orientation. LogiQuip can provide Tethering Kits for
the floor and wall. A unit with one (1) Gliding Basket does not need to secured. Configurations with more than one (1) Glide
Basket must use a Tethering Kit. No more than four (4) Glide Baskets can be used per cart.
Based on wall type the appropriate hardware needs to be determined by the installer to mount the D Ring Kit (PART 3)to the
wall. If the mounting surface is drywall you will need two (2) Toggle Bolts (PART 4)that must hold a minimum of 100 pounds
each. If the mounting surface is concrete or cinder block then use two (2) Screws (PART 5)that must hold a minimum of 100
pounds each.
1. Place one (1) Carabiner (PART 1)on each end of the metal Lanyard loops (PART 2).
2. Place the D Ring (PART 3)between the Flat and Curved Wall Mounting Brackets (PART 3).
3. Attach the D Ring Kit (PART 3)to the wall towards the top back of the Cart. This Tether Kit needs to be mounted in the
middle on the top Shelf or Basket.
4. Clip the Carabiner (PART 1)to the D Ring (PART 3)and then clip the other end with the Carabiner (PART 1)to the
back solid wire on one of the Flat Shelves or Baskets.
5. Push the Cart up against the wall and make sure the Lanyard is tucked behind the Baskets.
STEP 3 STEP 4 STEP 5
WARNING: Do not load more than 50 pounds in a Glide Basket. Do not pull out
more than one Glide Basket at a time. When pulling-out a Glide Basket, grab it at
the middle; do not pull it out from the side. Do not use the Glide Basket as a step.
STEP 1
STEP 2
11
ASSEMBLY GUIDE
LIMITED 5-YEAR WARRANTY
LogiQuip products are covered by a Limited 5-Year Warranty from date of receipt against defect in materials
or workmanship under normal use and service, excluding Electronic Components, Cart Covers, Custom
Products, LogiCell Tambour Doors, Label Holders, and Casters. During this period, LogiQuip will, in its sole
discretion, repair defects in materials or workmanship that existed when the product was received or replace
the product. Visit LogiQuip.com/Warranty for more details.
CUSTOMER SERVICE
If you have any problems with your ParWire® Basket Shelving, please contact our Customer Service
Department at:
PHONE: (800) 665-3760
EMAIL: CustomerSuppor[email protected]
ABOUT US
Healthcare exclusive since 1992, LogiQuip’s Inventory Management Solutions are designed for Healthcare
Professionals looking for a better way to manage supply chain tasks. With Expert Advice, Innovative Solutions,
and 360 Service that doesn’t stop after the sale, LogiQuip’s sole purpose is to ensure Healthcare Professionals
have the supplies they need when they need them. Partnering with you to design and implement the right solutions,
we give you time back to focus on what’s important; Patient Care.
Table of contents
Other Logiquip Rack & Stand manuals
