lhe Aulo Cic[o (Aulo Cycle) Setlings Io Increase Drying Time
If all your loads on all Auto Cic[os (Auto Cycles) are consistently not as dry as you would like, you may change the default settings
to increase the default dryness [eve[.
Your Auto Cic[o (Auto Cycle) drying settings can be adjusted to adapt to different installations, environmental conditions, or personal
preference. This change is retained and will affect all of your Auto Cic[os (Auto cycles), not just the current cycle/load. There are
3 drying settings, which are displayed using the "Status" lights (Moiado [Wet], HL]medo [Damp], Enfriamiento [Coo[ Down])
1 Factory preset dryness level.
2 Slightly drier clothes, 15% more drying time.
3 Much drier clothes, 30% more drying time.
To change the drying settings:
NOTE: The settings cannot be changed while the dryer is running or paused. The dryer must be in standby mode
(the Encendido [Power] button is off) to adjust the default settings.
1. Before starting a cycle, press and hold the TEMPERATU RA (Temperature) button for 6 seconds.
2. Press the TEMPERATURA (Temperature) button to select the dryness [eve[ shown in the LED display:
Mojado (Wet) light on = [eve[ 1, Mojado (Wet) and HL]medo (Damp) lights on = [eve[ 2, and Moiado (Wet), Humedo (Damp),
and Enfriamiento (Coo[ Down) lights on = [eve[ 3.
3. Press INICIO/PAUSA (Start/Pause) to save the new dryness [eve[ setting.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service ca[[.., http:!!www.maytag.com!he[p
if you experience Possible Causes Solution
Clothes are not drying Lint screen dogged with [int. Lint screen should be cleaned before each load.
satisfactorily, drying
times are too long, or The $6[o aire (Air only) cycle Select the right cycle for the types of garments being dried. See "Cycle
load is too hot has been selected. Guide".
Load too large and heavy Separate the load to tumble freely.
to dry quickly.
Exhaust vent or outside exhaust Run the dryer for 5-30 minutes. Hold your hand under the outside
hood is dogged with lint, exhaust hood to check air movement. If you do not fee[ air movement,
restricting air movement, dean exhaust system of lint or replace exhaust vent with heavy metal
or flexible metal vent. See the Installation Instructions.
Fabric softener sheets blocking Use only one fabric softener sheet, and use it only once.
the grille.
Exhaust vent is not the Check that the exhaust vent is not too long or has too many turns. Long
correct length venting will increase drying times. See the Installation Instructions.
Exhaust vent diameter is not Use 4" (102 mm) diameter vent material
the correct size.
Dryer located in a room with Proper operation of dryer cycles requires temperatures above 45°F (7°C).
temperature below 45°F (7°C).
Dryer located in a closet. Closet doors must have ventilation openings at the top and bottom of the
door. The front of the dryer requires a minimum of 1" (25 mm) of airspace,
and, for most installations, the rear of the dryer requires 5" (127 mm). See
the Installation Instructions.
Dryer will not run Door not dosed completely. Make sure the dryer door is dosed completely.
Inicio/Pausa (Start/Pause) button Press and HOLD the INIC[O/PAUSA (Start/Pause) button until you hear
not pressed firmly or long enough, the dryer drum moving.
Household fuse is blown Electric dryers use 2 household fuses or circuit breakers. The drum may
or circuit breaker has tripped, be turning, but you may not have heat. Replace the fuse or reset the
circuit breaker. If the problem continues, ca[[ an electrician.
Incorrect power supply. Electric dryers require 240-volt power supply. Check with a qualified
electrician.
Wrong type of fuse. Make sure you have right fuse.
10
