Maytag AGR5715QD User manual

AGR5715QD*
AGR5735QD*
AGR5835QD*
JGR8775QD*
JGR8875QD*
MGR5754QD*
MGR5755QD*
MGR5765QD*
MGR5775QD*
MGR5875QD*
16022498
Revision0
November2003
Gas
Freestanding
Range
This Base Manual covers general information
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
not limited to the following:
Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.

2 16022498 Rev. 0 ©2003 Maytag Appliances Company
Important Notices for Servicers and Consumers
Maytagwill not be responsible forpersonal injury or property damage fromimproper service procedures. Pride and
workmanship go into every product to provide our customers with quality products. It is possible, however, that during
its lifetime a product may require service. Products should be serviced only by a qualified service technician who is
familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing
instrumentsand the appropriate service information. IT IS THE TECHNICIANS RESPONSIBLITY TO REVIEW ALL
APPROPRIATE SERVICEINFORMATIONBEFOREBEGINNING REPAIRS.
!WARNING
Toavoid riskof severepersonal injuryor death,disconnect power beforeworking/servicing onappliance toavoid
electrical shock.
To locate an authorized servicer,please consult your telephone book or the dealer from whom you purchased this
product. For further assistance, please contact:
Customer Service Support Center
CAIRCenter
Web Site Telephone Number
WWW.AMANA.COM................................................ 1-800-843-0304
WWW.JENNAIR.COM ............................................. 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900
CAIR Center in Canada ........................................... 1-800-688-2002
AmanaCanadaProduct ........................................... 1-866-587-2002
Recognize Safety Symbols, Words, and Labels
DANGER!
DANGER—ImmediatehazardswhichWILL resultinseverepersonalinjuryordeath.
WARNING!
WARNING—Hazardsorunsafepracticeswhich COULDresultinseverepersonalinjuryordeath.
CAUTION!
CAUTION—Hazardsorunsafepracticeswhich COULDresultinminorpersonalinjury,productorproperty
damage.
Important Information

©2003 Maytag Appliances Company 16022498 Rev. 0 3
Table of Contents
Important Information..................................................2
Safety Information
Safety Practices for Servicer ..................................5
Servicing ..............................................................5
Receiving Oven .....................................................5
ALL APPLIANCES ................................................5
SELF-CLEANING OVEN........................................5
OVEN ..................................................................6
Delayed Ignition ....................................................6
Precautions ..........................................................6
In Case of Fire ......................................................6
Using the Oven .....................................................6
Baking, Broiling, and Roasting ...............................7
Connecting Range to Gas ......................................7
Electrical Requirements .........................................8
Extension Cord .....................................................8
Grounding.............................................................8
Product Safety Devices ..........................................9
General Information
Cooking Nomenclature......................................... 10
Rating label ........................................................ 11
Functional Operation ........................................... 11
Specifications ..................................................... 12
Model Identification.............................................. 12
Service ............................................................... 12
Parts and Accessories ........................................ 12
Extended Service Plan......................................... 12
Troubleshooting Procedures ..................................... 13
Testing Procedures .................................................. 16
H1 Control .......................................................... 20
M1 Control.......................................................... 24
M2 Control.......................................................... 25
Disassembly Procedures
Removing and Replacing Range ........................... 29
Front Control Panel ............................................. 29
Maintop Assembly .............................................. 29
Control Panel ...................................................... 29
Control Board Assembly ...................................... 29
Rocker Switch .................................................... 29
Top Surface Valve and Spark Switch..................... 29
Top of Surface Burner .......................................... 29
Bottom of Surface Burner ..................................... 29
Oven Sensor ....................................................... 30
Convection Fan Assembly.................................... 30
Bake Burner and Ignitor ....................................... 30
Broiler Burner and Ignitor ..................................... 30
Valve / Regulator Assembly ................................. 30
Automatic Oven Door Latch Assembly .................. 30
Spark Module ..................................................... 30
Door Plunger Light Switch.................................... 31
Oven Door Removal ............................................. 31
Oven Door Hinge Receptacle................................ 31
Side Panel Removal ............................................ 31
Backguard .......................................................... 31
Storage Drawer and
Storage Drawer Panel Removal ......................... 31
Storage Drawer Track Removal............................. 32
Oven Light Assembly........................................... 32
Frameless Door Disassembly .............................. 32
Power Cord......................................................... 32
Appendix A
Gas Conversion..................................................A-2
Surface Burners to LP/Propane Gas ....................A-3
LP Gas Surface Burner Orifice Configuration ........A-4
Natural Gas Surface Burner Orifice Configuration ..A-5
Converting Bake Burner Orifice............................A-6
Converting Broil Burner Orifice.............................A-8
Low Flow Conversion For Surface Burner Valves ...A-9

416022498 Rev. 0 ©2003 Maytag Appliances Company
As with all appliances, there are certain rules to follow for
safe operation. Verify everyone who operates the range is
familiar with the operations and with these precautions.
Use appliance only for its intended purpose as described.
Pay close attention to the safety sections of this manual.
Recognize the safety section by looking for the symbol
or the word safety.
Recognize this symbol as a safety precaution.
!
WARNING !
If the information in this manual is not followed exactly,
a fire or explosion may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
•Extinguish any open flame.
•Do not try to light any appliance.
•Do not touch any electrical switch; do not use any
phone in your building.
•Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
•If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by an
authorized installer, service agency or gas supplier.
WARNING !
To avoid risk of electrical shock, property damage,
personal injury or death; verify wiring is correct, if
components were replaced. Verify proper and complete
operation of unit after servicing.
WARNING !
This gas appliance contains or produces a chemical or
chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
To reduce the risk from substances in the fuel or from
fuel combustion make sure this appliance is installed,
operated, and maintained according to the instructions
in this manual.
Due to the nature of cooking, fires can occur as a
result of overcooking or excessive grease. Although a
fire is unlikely, if one occurs proceed as follows:
Oven Fires
1. Do not open the oven door.
2. Turn all controls to the OFF position.
3. As an added precaution turn off the electricity at
the main circuit breaker or fuse box and the gas
at the main supply valve.
4. Allow the food or grease to burn itself out in the
oven.
If smoke or fire persist call the local fire department.
To avoid risk of property damage or personal injury do
not obstruct the flow of combustion or ventilation air to
the oven.
To avoid risk of electrical shock, serious personal injury
or death: Verfiy the oven has been properly grounded
and always disconnect the electrical supply before
servicing this unit.
NOTE: The maximum gas supply pressure for these
models must not exceed 14 inches W.C.P.
Safety Information

©2003 Maytag Appliances Company 16022498 Rev.0 5
Safety Information
Safety Practices for Servicer
Safeand satisfactory operation of gasranges depends
uponitsdesign and proper installation. However,there is
one more area of safety to be considered:
Servicing
Listedbelow are some general precautions andsafety
practices which should be followed in order to protect the
servicetechnician and consumer duringservice and after
servicehas been completed.
1. Gas smell—Extinguish any and all open flames and
openwindows.
2. Turn gas off—Servicerange with gasturned off
unless testing requires it.
3. Checking for gas leaks—Never check for leaks with
any kind of open flame. Soap and water solution
should be used for this purpose.Apply solution to
suspectedarea and watch for air bubbles which
indicates a leak. Correct leaks by tightening fittings,
screws,connections, applying approvedcompound,
orinstalling new parts.
4. Using lights—Usea hand flashlightwhen servicing
ranges or checking for gas leaks. Electric switches
shouldnot be operated where leaks are suspected.
Thiswill avoid creating arcing or sparks which could
ignite the gas. If electric lights are already turned on,
they should not be turned off.
5. Do not smoke—Neversmoke while servicinggas
ranges,especially when working on piping that
contains or has contained gas.
6. Check range when service is completed—After
servicing, make visual checks on electrical
connection, and check for gas leaks. Inform
consumerof the conditionof range beforeleaving.
7. Adhere to all local regulations and codes when
performing service.
Receiving Range
• Installerneeds to show consumer location of the range
gasshut-off valve and how to shut it off.
• Authorized servicer must install the range, in
accordancewith the Installation Instructions.
Adjustmentsand service should be performed only by
authorizedservicer.
• Plug range into a 120–volt grounded outlet only. Do not
removeround grounding prongfrom the plug.If in doubt
about grounding of the home electrical system, it is
consumersresponsibility and obligation to have an
ungroundedoutlet replacedwith a properlygrounded
three-prongoutlet in accordance with theNational
Electrical Code. Do not use an extension cord with this
appliance.
• Insureall packing materials areremoved from the range
beforeoperating it, to preventfire or smoke damage
should the packing material ignite.
• Ensure range is correctly adjusted by a qualified
service technician or installer for the type of gas
(Naturalor LP). Some ranges can beconverted for use
with Natural or LP gas.
•Withprolonged use of a range,high floor temperatures
could result. Many floor coverings will not be able to
withstandthis kind of use. Never install range overvinyl
tile or linoleum that cannot withstand high
temperatures.Never install range directly over
carpeting.
ALL APPLIANCES
1. ProperInstallation—Be sure your appliance is
properlyinstalled and grounded bya qualified
technician.
2. NeverUseAppliance for Warmingor Heatingthe
Room.
3. Do NotLeave ChildrenAlone—Childrenshould not be
aloneor unattended in the areawhere the appliance
is in use. They should never be allowed to sit or stand
on any part of the appliance.
4. WearProperApparel—Loosefitting or hanging
garmentsshould never beworn while using appliance.
5. UserServicing—Donot repair or replaceany part of
theappliance unless specifically recommended in the
manual.All other servicing shouldbe referred to a
qualifiedtechnician.
6. Storagein or onAppliance—Flammable materials
shouldnot be stored in oven.
7. Do Not Use Water on Grease Fires—Smother fire or
flame, or use dry chemical or foam-type extinguisher.
8. UseOnly DryPotholders—Moist or damp potholders
on hot surfaces may result in burns from steam. Do
not let potholder touch burners. Do not use a towel or
other bulky cloth.
SELF-CLEANING OVEN
1. DoNot Clean Door Gasket—The door gasket is
essential for a good seal. Care should be taken not to
rub,damage, or move the gasket.
2. DoNotUse OvenCleaners—No commercial oven
cleaneror oven liner protective coatingof any kind
should be used in or around any part of the liner.
3. Clean Only Parts Listed in Manual. See Cleaning
section.
4. BeforeSelf-CleaningtheOven—Remove broilerpan,
oven racks, and other utensils.
5. Removeallitems from oven topand backguard.

6 16022498 Rev. 0 ©2003 Maytag Appliances Company
Safety Information
OVEN
1. UseCare WhenOpening Door—Let hot air or steam
escapebefore removingor replacingfood.
2. DoNotHeat UnopenedFood Containers—Build-up of
pressure may cause container to burst and result in
injury.
3. KeepOven VentsDuctsUnobstructed.
4. Placementof Oven Racks—Always place oven racks
in desired location while oven is cool. If rack is
removedwhile oven is hot, do notlet potholder
contacthot heating element in oven.
Delayed Ignition
Bake Burner Flame
Allowno more than 40–60 secondsbefore burner ignites
and heat is felt.To check for heat, open oven door to first
stopand place hand over oven door.If heat is not felt,
cancelbake funtion. If burner repeatedly fails to ignite,
contactanauthorized servicer.
Broiler Flame
Allowno more than 40–60 secondsbefore burner ignites
and flame is seen. If burner does not ignite cancel broil
function.If burner repeatedly fails to ignite within40–60
secondscontact an authorized servicer.
Radiant screen style broiler flame should appear hazy or
fuzzy. Haze should be no more than 3/8–inch thick. The
radiantscreen should begin to glow red within 1–2
minutes.
Precautions
• Donot mix household cleaning products. Chemical
mixturesmay interact with objectionable or even
hazardousresults.
• Do not put plastic items on warm cooking areas. They
may stick and melt.
• Do not use damp sponge or dishcloth to clean oven
when oven is hot. Steam from sponge or dishcloth can
burn.
• Donot leave fat heating unless you remain nearby. Fat
can ignite if overheated by spilling onto hot surfaces.
In Case of Fire
Fires can occur as a result of over cooking or excessive
grease.Though a fire is unlikely, if one occurs, proceed
as follows:
Oven Fires
1. Ifyousee smoke from oven, do notopen oven door.
2. Turnovencontrol toOFF.
3. As an added precaution, turn off gas supply and
power at main circuit breaker or fuse box.
4. Turnonvent to removesmoke.
5. Allow food or grease to burn itself out in oven.
6. If smoke and fire persist, call fire department.
7. If there is any damage to components, call repair
servicebeforeusing oven.
If smoke or fire persist call the local fire department.
To avoid the risk of property damageor personal injury do
not obstruct the flow of combustion or ventilation air to
theoven.
To avoid the risk of electrical shock, serious personal
injuryor death: Make sure your oven has beenproperly
groundedand always disconnect the electrical supply
beforeservicing this unit.
NOTE: The maximum gas supply pressure for these
models must not exceed 14 inches W.C.P.
Using the Oven
• Donot leave childrenalone or unattended where a
range is hot or in operation. They could be seriously
burned.
• Do not allow anyone to climb, stand or hang on the
door.They could damage the rangeand cause severe
personalinjury.
• Wearproper apparel. Loosefitting or hanging garments
shouldnever beworn when usingoven. Flammable
material could ignite if brought in contact with flame or
hotoven surfaces which may cause severeburns.
• Neveruserange for warming orheating a room. This
may cause burns, injuries, or a fire.
• Do not use water on grease fires.
• Do not let grease or other flammable materials collect
inor around range.
• Do not repair or replace any part of range unless it is
recommendedin this manual.
• Use only dry potholders. Moist or damp potholders
used on hot surfaces may result in a burn from steam.
Do not let a potholder touch the flame. Do not use a
towel or a bulky cloth as a potholder.
• Neverleaverange unattendedwhile cooking.Boilovers
can cause smoking and may ignite.

©2003 Maytag Appliances Company 16022498 Rev. 0 7
Safety Information
•Only certain types of glass/ceramic, earthenware, or
other glazed utensils are suitable for oven use.
Unsuitable utensils may break due to sudden
temperature change.
•Use care when opening oven door. Let hot air or steam
escape before removing or replacing food.
•Do not heat unopened food containers in oven.
Build-up of pressure may cause a container to burst
and result in injury.
•Keep range vent ducts unobstructed.
•Place oven racks in desired location while oven is cool.
If a rack must be moved while oven is hot, use a dry
potholder.
•Do not use aluminum foil to line oven bottom or racks.
Aluminum foil can cause a fire and will seriously affect
baking results, and damage to porcelain surfaces.
•Do not touch interior surfaces of oven during or
immediately after use. Do not let clothing or other
flammable materials come in contact with bake or broil
burners.
•Other areas of the oven can become hot enough to
cause burns, such as vent openings, window, oven door
and oven racks.
•To avoid steam burns, do not use a wet sponge or cloth
to wipe up spills on hot cooking area.
•Do not store combustible or flammable materials, such
as gasoline or other flammable vapors and liquids near
or in oven.
•Do not clean oven door gasket located on back of the
door. Gasket is necessary to seal the oven and can be
damaged as a result of rubbing or being moved.
•Do not drape towels or any materials on oven door
handles. These items may ignite causing a fire.
CAUTION !
Do not store items of interest to children in cabinets
above range. Children may climb on oven to reach
these items and become seriously injured.
Baking, Broiling, and Roasting
•Do not use oven area for storage.
•Stand back from range when opening door of a hot
oven. Hot air or steam can cause burns to hands, face,
and eyes.
•Do not use aluminum foil anywhere in the oven. This
could result in a fire hazard and damage the range.
•Use only glass cookware appropriate for use in gas
ovens.
•Always remove broiler pan from oven when finished
broiling. Grease left in pan can catch fire if oven is used
without removing grease from the broiler pan.
•When broiling, meat that is close to the flame, may
ignite. Trim any excess fat to help prevent excessive
flare-ups.
•Make sure broiler pan is placed correctly to reduce any
possibility of grease fires.
•Should a grease fire occur in the broiler pan, turn off
oven, and keep oven door closed until fire burns out.
Connecting Range to Gas
Install manual shut-off valve in gas line for easy
accessibility outside range. Be aware of the location of
the shut-off valve.

8 16022498 Rev. 0 ©2003 Maytag Appliances Company
Safety Information
Electrical Requirements
120-volt, 60 Hertz, 15 amp, individual circuit which is
properlygrounded, polarized and protected by a circuit
breakeror fuse.
Extension Cord
Due to possible pinching during installation, extension
cords should not be used on products.
Extensioncords will adversely affect theperformance of
spark system.
Grounding
NOTE: Thisappliance must be properlygrounded, for
personalsafety.
Power cord on this appliance is equipped with a three-
pronggrounding plug. Thismatches standard three-prong
groundingwall receptacle to prevent possibility of electric
shock from this appliance.
Consumershould have wall receptacle andcircuit
checked by qualified electrician to verify receptacle is
properlygrounded.
Wherestandard two-prong wall receptacle is
encountered, it is consumers responsibility and
obligationto have it replaced witha properly grounded
three-prongwall receptacle.
DO NOT, UNDERANYCIRCUMSTANCES, CUT OR
REMOVETHE THIRD (GROUND)PRONG FROM
POWER CORD.
For 15 amp circuits only. Do not use an adapter on 20
amp. circuit. Where local codes permit, a TEMPORARY
CONNECTIONmay bemade toproperly grounded two-
prong wall receptacle by the use of a UL listed adapter
availableat most hardware stores.
Larger slot on adapter must be aligned with larger slot in
thewall receptacle to provide properpolarity.
WARNING
!
Attachingadapter ground terminalto wall receptacle
coverscrew does notground appliance unlessthe
cover screw is metal and not insulated, and wall
receptacleis groundedthrough the housewiring.
Consumershould have circuitchecked by aqualified
electricianto verifyreceptacle is properlygrounded.
Whendisconnecting power cord from adapter,always
hold adapter with one hand. If this is not done, adapter
ground terminal is very likely to break with repeated use.
Should this happen, DO NOT USE appliance until a
properground has been established.
Neutral Wire
Hot Lin
e
Ground
NOTE: Circuit tester can be use to verify voltage is
present at the outlet, connect one lead to hot
line and the other lead to ground, circuit tester
should light.

©2003 Maytag Appliances Company 16022498 Rev.0 9
Product Safety Devices
Safetydevices and features have been engineered into the productto protect consumer and servicer.Safety devices
mustnever be removed, bypassed, or altered in such a manner as to defeat the purpose forwhich they were intended.
Listedbelow are various safety devices together with the reason eachdevice is incorporated in the gas ranges.
Pressure Regulator Maintainsproper andsteady gas pressure for operationof ovencontrols. Regulator
must be set for the type of gas being used Natural or LP.After servicing regulator,
make certain it is set properly before completing service.
Gas Burner Orifices These products use a fixed orifice fitting that must be installed forNatural or LP.
Afterservicing avalve ororifice verifyit isproperly operatingbefore completing
service.
Oven Safety Valve Ovenvalve is designedto be asafety valve.Twobasicdesigns are used in gas
ranges.
Hydraulictypevalve
Electrictype valve
Bothtypes are safety valvesbecause they are indirectlyoperated by the oven
thermostat, which controls a pilot flame or electric ignitor, to open and close the oven
valve.
These products use the Electric Type Valve.
Grounded Oven Frame Groundprong on powercord is connected tothe frame, usually agreen lead fastened
by a screw. In addition, any part or component capable of conducting an electric
current is grounded by its mounting.
If any ground wire, screw, strap, nut, etc. is removed for service, or any reason, it
mustbe reconnected to itsoriginal position with original fastener before the appliance
is put into operation again.
Failure to do so can create a possible shock hazard.
Safety Information

General Information
10 16022498 Rev. 0 ©2003 Maytag Appliances Company
Cooking Nomenclature
A
G R 5 7 1 5 Q D W
Brand
AAmana
CMagic Chief
GGraffer &
Sattler
HHardwick
JJenn-Air
MMaytag
NNorge
UUniversal
YCrosley
Product Type
AAccessory/Cartridge
CCooktop Updraft/Countertop
DDowndraft Cooktop or Warming Drawer
EEyelevel Range
GGrill
LRange (20")
MRange (36")
PDrop In (24")
QWall Oven (27")
RRange, Free-Standing (30")
SSlide-In (30")
TRange Hood
VOTR
WWall Oven
YRV Range
ZRV Top
Fuel
BButane
DDual Fuel
E/J Electric
GGas, Natural
LLiquid Propane
MMicrowave
PStanding Pilot
XNo Fuel
WWarming Drawer
Listing
AUL/AGA
CCSA/CGA/CUL
DDual Listed
G220-240 V / 50-60 Hz
MMilitary Model
PPSB Approved
(Singapore)
XExport 120 V / 60 Hz
Feature Content
1000-3999 Brands
4000-6999 Maytag/Amana
7000-9999 Jenn-Air
Production Code
This identifies which
version of production the
unit is.
Color
AAlmond on Almond
BBlack
C Brushed Chrome
H Traditional White
LTraditional Almond
PProstyle
Q Monochromatic Bisque
SStainless
TTraditional Bisque
W White on White
FFrost White (True Color White)
N Natural Bisque (True Color Bisque)
This manual provides basic instructions and suggestions
for handling, installing , and servicing gas ranges.
The directions, information, and warnings in this manual
are developed from experience with, and careful testing of
the product. If the unit is installed according to the
Installation Instructions, it will operate properly and will
require minimal servicing. A unit in proper operating order
ensures the consumer all the benefits provided by
efficient gas cooking.
This manual contains information needed by authorized
service technicians to install and service gas ranges
pertaining to this manual. There maybe, however some
information which needs further explanation. Refer to
individual Installation Instructions, Use and Care,
Technical Sheets, or toll free technical support line to
answer questions from authorized service technicians.

General Information
©2003 Maytag Appliances Company 16022498 Rev. 0 11
Rating Label
Model numbers are recorded on the rating label. Rating
label is located on the lower front right corner of the oven
frame. It can be seen by opening the oven door. Before
ordering parts, write down the correct model and serial
number from rating label. This avoids incorrect shipments
and delays. Please refer to parts reference material when
ordering replacement parts.
Functional Operation
The glow bar system is completely reliant upon
electricity. When the oven control is turned on, 120 VAC
is provided to the glow bar ignitor and the gas valve
circuit. The high resistances of the glow bar limits the
current flow through the ignitor/gas valve. Continual
current flow through the circuit causes the glow bar
ignitor to glow brighter and the resistance of the ignitor
decreases, which increases the current flow through the
ignitor/gas valve circuit. This increases the amount of
heat generated by the heater, which causes the bi-metal
to bend.
At a point the ignitor resistance will have increased to
approximately 3.5 amps of current flow through the
ignitor/gas valve circuit. In approximately 45 seconds the
glow bar ignitor temperature will have increased to
approximately 2650°F. the voltage drop across the gas
valve terminals will have increased to about 3 VAC, which
will indicate enough current to flow to provide enough
bi-metal heat to cause the gas valve to open providing
gas flow to the oven burner the heat from the glow bar
ignites the gas. The sensing element of the oven control
then cycles contacts within the oven control, opening and
closing to cycle the glow bar, safety valve, and burner to
maintain the desired temperature.
NOTE: This system cannot operate without electricity.
The primary components of this ignition system are:
electronic control, ignitor, and safety valve. These
components are all wired in series and although the oven
control and glow bar require 120 VAC, 60 Hz. The oven
valve operates on approximately 3 volts.
Therefore, 120 VAC should never be applied directly to
the oven valve terminals. The glow bar is the power
source for the oven valve.

General Information
12 16022498 Rev. 0 ©2003 Maytag Appliances Company
Specifications
Referto individualTechnical Sheet forinformation
regardingspecifications.
Model Identification
Completeregistration card and promptly return.If
registration card is missing:
• ForAmanaproduct call1-800-843-0304 or visit the
Web Site at www.amana.com
• ForMaytag product call 1-800-688-9900 orvisit the
Web Site at www.maytag.com
• ForJenn-Air product call1-800-536-6247 or visitthe
WebSite at www.jennair.com
• For product in Canadacall 1-866-587-2002or visitthe
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
Whencontacting provide productinformation located on
ratingplate. Record the following:
ModelNumber: ___________________
ManufacturingNumber: ___________________
Serialor S/N Number: ___________________
Dateof purchase: ___________________
Dealer’sname and address: ___________________
Service
Keep a copy of sales receipt for future reference or in
casewarranty service is required.Tolocate an authorized
servicer:
• ForAmanaproduct call1-800-628-5782 or visit the
Web Site at www.amana.com
• ForMaytag/Jenn-Air productcall 1-800-462-9824 or
visit the Web Site at www.maytag.com or
www.jennair.com
• For product in Canadacall 1-866-587-2002or visitthe
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
Warrantyservice must be performed by an authorized
servicer.We also recommendcontactingan authorized
servicer,if serviceis required afterwarranty expires.
Parts and Accessories
Purchasereplacement parts and accessories over the
phone.To order accessories for your product call:
• ForAmana product call1-877-232-6771 or visit the
Web Site at www.amana.com
• ForMaytag/Jenn-Air productcall 1-800-462-9824 or
visit the Web Site at www.maytag.com or
www.jennair.com
• For productin Canada call 1-866-587-2002or visitthe
Web Sites at www.amana.com or www.maytag.com or
www.jennair.com
Extended Service Plan
Weoffer long-term service protectionfor this new oven.
• Asure™ Extended Service Plan is specially designed
tosupplementAmana’s strong warranty. This plan
coversparts, labor,andtravel charges.
Call1-866-232-6244for information.
• Dependability PlusSM Extended Service Plan is
specially designed to supplement Maytag’s and
Jenn-Air’sstrong warranty.This plan covers parts,
labor,andtravel charges.
Call1-800-925-2020for information.

Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
©2003 Maytag Appliances Company 16022498 Rev. 0 13
Problem Possible Cause Correction
Burners will not ignite; no
spark at top burner.
Poor ground on burner cap.........................
Weak or failed spark module.......................
Low gas pressure........................................
•Clean burner cap.
•Replace spark module.
•Verify pressure 4” WCP for
natural, 10” WCP for LP.
Burner will not ignite. No
spark to burner ignitors
when burner knob is rotated
to “LITE” position.
No 120 VAC to range..................................
Micro switch contacts not closing................
Faulty wiring. Bad connection at burner
electrode and electrode socket...................
Inoperative spark module............................
Electrode dirty. Burner cap dirty..................
Cracked or broken electrode, electrode
wire or electrode socket..............................
•Verify voltage at wall outlet.
•Check wiring against appropriate
wiring diagram, Verify all
terminals and connections are
correct and tight. Check micro
switch contacts.
•Check wiring against appropriate
wiring diagram. Verify all
terminals and connections are
correct and tight.
•Check module according to
testing procedures information.
•Clean electrode or burner cap.
•Replace electrode.
No spark or only random
spark at one ignitor.
Check for cracked ignitor or pinched ignitor
wire .............................................................
Poor continuity to burner cap......................
Bad ground connection or lack of continuity
to ground or ignitor......................................
Cracked or broken ignitor extension lead ...
•Replace ignitor lead or electrode.
•Clean burner cap and lead.
•Tighten ground connection and
correct any breaks in ground path
from ignitor path to unit ground
path.
•Replace ignitor lead.
Unit continues to spark after
knob is turned to OFF
position.
Shorted valve switch/harness .....................
Switch has slipped off the valve..................
•Replace switch/harness. If
shorting is caused by excessive
spillovers, customer education is
advised.
•Carefully reposition switch on
valve and rotate from OFF to
high, several times to verify
switch is not broken.
No oven operation in bake or
broil.
No voltage to control. ..................................
No voltage from control...............................
Loose wire connection or broken wire.........
•Check for 120 VAC at control. If
no voltage check power source.
•Check 120 VAC to ignitor, if no
voltage, replace control.
•Verify all connections are clean
and tight, replace broken wire.

Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
14 16022498 Rev. 0 ©2003 Maytag Appliances Company
Problem Possible Cause Correction
No gas flows to burner.
Ignitor glows red.
Failed ignitor................................................
Gas pressure too high.................................
Failed gas valve ..........................................
Loose wire connection or broken wire.........
•Check ignitor current draw, 3.2 –
3.6 Amps. Replace ignitor, if it
fails test.
•Check for correct gas pressure.
Natural gas pressure should be
4" WCP and LP gas pressure
should be 10" WCP.
•Check gas valve for continuity.
•Verify all connections are clean
and tight, replace broken wire.
Gas flows to bake/broil
burner, but burner does not
light.
Ignitor positioned too far from burner..........
Dirt or grease in orifice or burner ................
Insufficient gas pressure .............................
Power outage ..............................................
•Reposition ignitor closer to
bake/broil burner.
•Clean orifice or burner.
•Check for correct gas pressure.
Natural gas pressure should be
4" WCP and LP gas pressure
should be 10" WCP.
•Verify power is present at unit.
Verify that the circuit breaker is
not tripped.
•Replace household fuse, but do
not fuse capacity.
Broil burner shuts off shortly
after the start of self-clean
operation. Bake and broil
functions operate normally.
Power outage ..............................................
•Verify power is present at unit.
Verify that the circuit breaker is
not tripped.
•Replace household fuse, but do
not fuse capacity.
•Refer to Use and Care Manual
“Operating Instructions”, if
continues contact service.
Fan motor does not operate.
No power to fan motor.................................
Failed fan motor or winding or frozen shaft.
•Check for 120 VAC supplied at
fan motor. If no voltage is
present, check for broken or
loose wiring between fan motor
and relay board. If voltage is
present at fan motor, go to the
next step.
•Check motor winding for
continuity. Check for a frozen
motor shaft. Check for broken
wiring between motor and neutral
terminal block.

Troubleshooting Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires it.
©2003 Maytag Appliances Company 16022498 Rev. 0 15
Problem Possible Cause Correction
Oven light does not operate.
Failed oven lamp.........................................
Failed wiring ................................................
Failed light socket........................................
Failed light plunger/switch...........................
•Check lamp and replace is
necessary.
•Check for broken, loose or dirty
connections.
•Check light socket for continuity.
•Check plunger/switch for
continuity. Check wiring diagram
for application.
Self-clean cycle not working
Programming error......................................
•Shut off power to oven for five
minutes by switching off circuit
breaker. Reset circuit breaker
and try oven again.
Oven door will not unlock
Oven is self-cleaning...................................
Oven is still hot............................................
•Allow cycle to complete.
•Door will not unlock until unit has
cooled to safe temperature. Do
not force door open, this will void
warranty. Blow cool air on door
latch area to quicken process.
Oven smokes/odor first few
times of usage
Normal......................................................... •Minor smoking and/or odor is
normal the first few times of oven
usage.
•Ventilate area well and perform
self-clean cycle.
Failure Codes Electronically Controlled.............................. •See Testing Procedures for
diagnostic checks.

Testing Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
16 16022498 Rev. 0 ©2003 Maytag Appliances Company
Illustration Component Test Procedure Results
Oven light socket Test continuity of receptacle terminals.
Measure voltage at oven light.
Indicates continuity with bulb screwed in.
120 VAC, see wiring diagram for terminal
identification.
If no voltage is present at oven light
check wiring.
NC
NO
C
Door plunger switch Remove switch from unit and measure
the following points:
C-NO
Plunger in continuity, Plunger out infinite.
Rocker switch Measure continuity of switch positions:
Closed ..............................................
Open.................................................
Continuity
Infinite
COM NO
NC
Door light switch Switch connection in following
positions:
Not engaged
Engaged
Normally Open
COM-NO=Open, COM-NC=Closed
COM-NO=Closed, COM-NC=Open
Autolatch assembly
with switch Disconnect wires and test for continuity per wiring diagram. See wiring diagram for schematic layout.
Refer to Parts Manual for correct
autolatch switch.
Bake burner Verify gas is supplied.
Orifice adjusted for Natural or LP.
Check for obstructions, contamination
in ports or damage.
Clean with hot soapy water and dry
completely.
Replace if punctured or torn.
Broil burner Verify gas is supplied.
Verify proper orifice installed for
Natural or LP.
Check for obstructions, contamination
in ports or damage.
Clean with hot soapy water and dry
completely.
Replace if punctured or torn.
Ignitor Test for voltage at terminals ...............
Test for the amount of amperage in the
circuit..................................................
(Ignitor may glow, but not have
sufficient amperage to open valve).
120 VAC
3.2−3.6 Amps.
Temperature sensor Measure resistance.
Approximately 1100 Ωat room
temperature 80ºF.
Convection motor fan Verify supply voltage ........................
Measure continuity at the following
points:
Terminal to terminal..........................
Terminal to ground...........................
120 VAC
Continuity
Infinite
Convection element Test continuity of terminals...............
Test voltage to terminals ..................
Approximately 14 Ω- cold
120 VAC

Testing Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
©2003 Maytag Appliances Company 16022498 Rev. 0 17
Illustration Component Test Procedure Results
Pressure regulator Verify gas pressure (WCP).
If on LP service, verify proper gas
supply conversion.
4"Natural
10"LP/Propane
GND L or N
Input
Spark module
4 + 0 Test for voltage at terminals L and N...........................................
Polarity and ground ........................
120 VAC
Not subject to polarity
Holder orifice Verify gas pressure (WCP).
Check orifice for debris.
4"Natural
10"LP/Propane
Clean as needed.
Spark ignition
electrode Test for resistance of spark lead..........
Test ignitor to chassis..........................
Continuity
No continuity from ignitor to chassis.
270°valve
Verify gas is supplied.
Verify Orifice for
Natural or LP.
Adjust set screw for simmer control.
Fixed orifices for Natural or LP.
See conversion section.
Spark 270°switch Unplug switch harness at rear of
range. Test for continuity at wire
terminals.
Switch in LITE position.......................
Switch in any other position................
120 VAC
Continuity
Infinite
Top surface burner
Verify gas is supplied...........................
Verify burner cap is positioned
correctly.
Check for obstructions in burner ports.

Testing Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
18 16022498 Rev. 0 ©2003 Maytag Appliances Company
Illustration Test Procedure Results
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ωfor Cancel pad
1000 – 15000 Ωfor All other pads
1
16
98
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Clean
Keep Warm
Favorites
Timer
Light
Trace
13 & 15
12 & 15
10 & 15
7 & 13
12 & 13
10 & 12
4 & 13
4 & 12
4 & 10
5 & 12
1 & 2
5 & 14
15 & 14
4 & 5
7 & 15
13 & 14
7 & 14
5 & 13
4 & 14
12 & 11
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ωfor Cancel pad
1000 – 15000 Ωfor All other pads
1
16
98
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
Convect
Clean
Keep Warm
Favorites
Timer
Light
Trace
5 & 14
4 & 14
4 & 13
4 & 12
4 & 10
13 & 14
4 & 5
5 & 13
5 & 12
5 & 10
1 & 2
13 & 15
12 & 11
7 & 15
7 & 14
10 & 11
10 & 12
4 & 7
10 & 15
12 & 13
12 & 15
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity

Testing Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
©2003 Maytag Appliances Company 16022498 Rev. 0 19
Illustration Test Procedure Results
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ωfor Cancel pad
1000 – 15000 Ωfor All other pads
1
16
98
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Convect Bake
Convect Roast
Keep Warm
Bake
Broil
Clean
Drying
Proofing
Timer
Clock
Cook & Hold
Favorite
Light
Trace
13 & 15
12 & 15
10 & 15
7 & 13
12 & 13
10 & 12
4 & 13
4 & 12
4 & 10
5 & 12
1 & 2
7 & 11
11 & 13
4 & 7
7 & 15
4 & 5
5 & 7
11 & 12
5 & 10
4 & 11
5 & 11
11 & 15
5 & 13
10 & 11
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Matrix
Control Panel Assembly
Continuity is indicated as follows:
1000 – 6600 Ωfor Cancel pad
1000 – 15000 Ωfor All other pads
1
16
98
Pad
1
2
3
4
5
6
7
8
9
0
Cancel
Clock
Cook & Hold
Broil
Bake
CV Bake
CV Roast
Clean
Keep Warm
Favorites
Timer
Light
Trace
13 & 15
12 & 13
12 & 15
4 & 11
4 & 12
4 & 10
5 & 13
5 & 12
5 & 10
10 & 12
1 & 2
4 & 5
4 & 7
5 & 7
10 & 11
4 & 13
7 & 11
7 & 15
11 & 12
13 & 14
5 & 11
7 & 13
Measurement
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity
Continuity

Testing Procedures
!WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless
testing requires power.
20 16022498 Rev. 0 ©2003 Maytag Appliances Company
Illustration Component Test Procedure Results
H1 Controlled Oven temperature
adjustment Press BAKE pad. Enter 550 on the digit-pad.
Immediately press and hold BAKE
pad for 3 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing AUTOSET pad. To avoid
over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry timer
to expire to accept the change.
Temperature adjustment will be
retained even through a power failure.
While increasing or decreasing oven
temperature, this does not affect self-
cleaning temperature.
H1 Controlled Temperature display Press and hold Cancel and Bake
pads for 3 seconds. This mode enables the user to indicate
°F or °C on the display.
H1 Controlled Clock Display Press and hold Cancel and Clock
pads for 3 seconds. Allows clock to be toggled On or OFF.
H1 Controlled 24 Hour Clock Press and hold Cancel and Favorite
pads for 3 seconds. Allows the time on the clock to be toggled from 12 hour or 24 hour display.
H1 Controlled Factory Default Press and hold Cancel and Keep
Warm pads for 3 seconds. Allows the clock to be reset to factory settings.
H1 Controlled Twelve hour off Control will automatically cancel any
cooking operation and remove all
relay drives 12 hours after the last pad
touch.
See Sabbath mode to disable.
H1 Controlled Sabbath Mode Hold CLOCK pad for 3 seconds to
activate Sabbath mode.
Hold CLOCK pad for 3 seconds to
disable Sabbath mode.
“SAb” will be displayed and flash for 5
seconds.
Display will go back to time of day.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
H1 Controlled Child lock out Press and hold Cancel and Cook &
Hold pads for 3 seconds. “OFF” will
display where the temperature
normally appears. “LOCK” will display
flashing while door is locking.
To reactivate the control, press and
hold Cancel and Cook & Hold pads
for 3 seconds.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
H1 Controlled Diagnostic Code
Display See “Quick Test Mode”.
Cycle through the codes using the
number pads 1 through 5.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See “Description of Error Codes” for
explanation.